Instructions for the Use and Care and Installation of ORW6XA ORW9XA Wall Canopy Rangehoods
CONTENTS 1 Notice 2 Features 3 Installation 4 Notice of installation 5 Safety Warning 6 Use Instructions 7 Maintenance 8 Troubleshooting 9 Specification It is important that you retain these instructions, proof of purchase as well as other important documents about this product for future reference. Due to continual product development, Omega reserves the right to alter specifications or appearances without notice. Dispose of packaging responsibly – recycle where facilities are available.
(1) NOTICE 1. Thank you for choosing our cooker hood. Please read the instruction manual carefully before use. 2. The installation work must be undertaken by a qualified electrician and competent installer. 3. The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text. The cooker hood is rated for use on 220/240v, 50Hz.
(2) FEATURES 1. The cooker hood uses high quality materials, and is made with a streamlined design. 2. Equipped with a high power electric motor and centrifugal fan, it produces strong suction with low noise, and features a non stick grease filter which is easy to clean. 3. The isolated low voltage (12 volt) circuit board control, means the halogen lights are brighter and safer than incandescent alternatives. 4.
(3) INSTALLATION 3.1 The cooker hood should be placed at a distance of 65-75cm (26-30inch) from the cooking surface for the best effect. See Pic 1. 3.2 Install the hook in a suitable place once the installation height is fixed, and keep it vertically aligned. The fixed position of the inside chimney bracket determines the location of the chimney. 3.
(4) NOTICE OF INSTALLATION 1. Before installation, please ensure the area is clean, to avoid suction of the remaining bits of broken wood and dust. 2. The canopy hood cannot share the same air ventilation ducting as other appliances, such as gas and electric heaters. 3. The bending of the ventilation ducting should be ≥ 120°, parallel or above the exit vent, and should be connected through the external wall. 4.
(5) SAFETY WARNING Keep your children from using the cooker hood. Your cooker hood is for domestic use only, not suitable for barbecue, fast - food shops, and other commercial use. Any installation work must be carried out by a qualified electrician or competent person. The cooker hood and its filter mesh should be cleaned regularly in order to keep in good working order. Before cleaning, always ensure that you have switched your cooker hood off.
(6) USE INSTRUCTIONS The re-usable aluminium grease filters supplied with this rangehood should be cleaned every month or so to avoid grease build-up. To remove the grease filter, release the locking mechanism at the front of the filter, and lower the filter slightly to unhook it at the back. Whilst the filter is removed, clean off any residual grease from the housing to avoid fire risk. When replacing the grease filters, ensure that the locking mechanism is facing down.
SPEED ADJUSTMENT - See pictures 1. Push ‘Stop’ button, and the motor will stop. 2. Push the ‘Low’ button, the buzzer will buzz once, and the motor runs at low speed. 3. Push the ‘Mid’ button, the buzzer will buzz once, and the motor runs at mid speed. 4. Push the ‘High’ button, the buzzer will buzz once, and the motor runs at high speed. 5. Push the ‘Light’ button and the two lights will come on. Push it again and the light will turn off.
(7) MAINTENANCE 7.1 Cleaning the grease filter mesh The filter mesh is made of high-density stainless steel. Please do not use corrosive detergent on it. Keeping this filter clean will keep the appliance running correctly. Please strictly follow the guidelines below. Method 1: Place the mesh in 40 - 50 DegC clean water, add in a small amount of detergent, and soak for 2 - 3 minutes. Wear gloves, and clean with a soft brush. Do not apply too much pressure, as the mesh is delicate and will damage easily.
(8) TROUBLESHOOTING Fault Cause The fan is blocked Light on, but motor does not work The capacitor damaged Solution Remove the source of the blockage Replace capacitor The motor jammed and Replace motor bearing damaged A smell coming from the Replace motor motor Beside the above mentioned, check the following: Light does not work, motor does not work Oil leakage Shake of the body Insufficient suction The machine inclines Light damaged Replace lights Power cord loose Take to authorised service
(9) SPECIFICATION Rated Input Rated Power Lighting Power Motor Power Air tube diameter Air output 220V-240V, 50Hz 230W 20W X 2 (halogen capsule lamp) 190W 150MM 700m3/h
