Installation
Installing Latch - Skip to #4 Instruction if door is pre-bored.
1. Using template, mark all points for drilling. Use correct
backset for latch. Drill 2 " bore first. For smaller (52mm)
diameter rose or narrow plates drill ¾" diameter hole
instead of 2 " bore.*
2. Using 1" boring bit, drill from the center of the door edge,
at 38”FROM FLOOR mark, into the 2 " bore.
3. With face cover in place, position latch and mark perimeter
of latch faceplate on door edge. Mortise to accommodate
latch face and face cover, approximately " deep.
4. PASSAGE: When installing a passage latch, hold latch
with writing facing upwards.
PRIVACY: When installing privacy latch, hold latch with
writing facing upwards. The side of latch that is inside of
the room must be towards you. Push in the privacy locking
block. Slide the oval plastic stopper over the outside
privacy block. Fasten with the small machine screw
(see Figure #1 on reverse side).
5. Rotate latch bolt if necessary, using slight pressure. Apply
faceplate with flat side of faceplate facing flat side of bolt.
Position latch in door to suit bevel. Screw faceplate and
latch to door.
6. Before installing roses, insert spindle through latch hub.
THIS MUST BE DONE BEFORE THE ROSES ARE
INSTALLED. For privacy, the spindle should be inserted
through latch from exterior side of door, with the stop of
spindle on same side. The tear drop cutout of spindle
should face the set screw position on the knob or lever.
INSTALLATION INSTRUCTIONS FOR
STAINLESS STEEL LATCHSETS
Installing Passage and Privacy Rose Set
1. Remove the covers from both sides of the roses. Install the
plastic sub-roses to each other through the door and
fasten them together using the (2) screws provided.
PRIVACY: For privacy, make sure both roses
have the words “Door Edge” facing the correct
direction for the privacy pin. Install the (2) screws
to fasten the roses together (do not tighten them
down but leave them snug). Slide the levers onto
the splindle on both sides and turn the sub-roses
so that the ends of the levers are slightly pointing
upwards. Tighten the screws to fasten the sub-
roses together.(DO NOT OVERTIGHTEN SCREWS.)
Slide off the lever handles.
2. Replace the rose covers on to the sub-roses by aligning
the cut-out of the cover with the tab of the plastic sub-rose.
Snap rose covers onto sub-roses.
3. Slide both levers onto spindle until securely seated into
roses. (For privacy, ensure the spindle is centered in the
latch so each lever works independently). With set screws,
fasten levers to spindle. If installing privacy, thread privacy
pin through rose into latch after trim is applied.
4. Check for smooth operation.
Your Omnia Dealer/Distributor can help you with any further
questions or information on other Omnia Products.
1
/
8
1
/
5
/
32
CEDAR GROVE, NJ 07009
MNIAO
INDUSTRIES , INC.
R
12/30/10
TUBULAR LATCH TEMPLATE
FOLD ALONG DOOR EDGE
DRILL 1" DIA. HOLE
IN DOOR EDGE
1 "
DOOR
3
4
1 "
DOOR
3
8
3
8
38" FROM FLOOR
3
4
2 " BACKSET
2 " BACKSET
11
16
"
7
8
"
5
32
"
OM-TLSS V2
1
/
8
1
/
8
2 " BORE
FACEPLATE
1” x 2 ”
1
/
4
3
4
" DIA. HOLE
" DIA. HOLE
5
16
" DIA. HOLE
5
16
*
*
*
*DRILL FOR SMALLER (52MM)
DIAMETER ROSE ONLY.
NOTE: Template may not be true-to-size. Please use for reference
purposes only. DO NOT drill until measurements are verified.
8
CAUTION: DOOR AND FRAME MANUFACTURERS
When door gasketing or silencers are used, proper allowances must be made for strike location to
.
maintain a common centerline with lock and door so that the bolt will freely enter strike