C-2600U DIGITAL SPEAKER PROCESSOR Beta three User Manual Beta Three 1 INPUT A 2 B COMP LIMITER IN-1 LIMITER OVER OVER IN-2 OVER OUTPUT C D IN-1 LIMITER IN-1 LIMITER IN-2 OVER IN-2 OVER IN-1 LIMITER OVER -6 IN-2 OVER -10 MF LF -20 SLF -40 HF -6 HF -6 HF -6 -10 -10 MF -10 MF -10 MF -20 -20 LF -20 LF -20 SLF -40 SLF -40 -40 F LIMITER IN-2 HF -6 -40 E IN-1 -6 RECALL /ENTER IN-1 PROGRAM IN-2 STATUS HF REMOTE/ID HF -6 -10 MF -10 MF
CONTENT DIGITAL SPEAKER PROCESSOR 1. PRECANTION 1 2. INTRODUCTION 2 2.1 Audio features 2 2.2 User interface 2 2.3 Other features 2 3. UNPACKING 3 4. AC POWER REQUIREMENTS 3 5. FRONT PANEL CONTROL FEATURES 4 6. REAR PANEL INTERCONNECT FEATURES 5 7. DISPLAYS AND OPERATION 6 8. 9. 7.1 Switching display mode 6 7.2 Indications and operations at lock 7 7.3 Display and operation during external control 7 7.4 To recall 7 7.
1> PRECARTIONS DIGITAL SPEAKER PROCESSOR ABNORMAL PHENOMENA: Please turn off the power and pull out the plug when you find unusual sound or smell when operation. POWER CORDS PROTECTION Don't touch power cords with wet hands to avoid electric shock. Don't put the cords in crowded people. KEEP AWAY FROM WATER AND SUNDRY GOODS DON'T OPEN THE COVER IF NOT GUIDED BY A QUALIFIED ELECTRICIAN PULL OUT THE POWER CORDS TO AVOID FIRE WHEN YOU DON'T USE THIS UNIT.
2> INTRODUCTION DIGITAL SPEAKER PROCESSOR Thank you for your purchasing of the DEVICE digital speaker processor. This processor builds on the advanced and experienced ideas of design and marketing, the excellent audio performance and competitive quality/price ratio make sure your interests. This unit DEVICE , can provide two channel analog precise signal the precise digital control. She has audio processor and audio management functions. It can be used to the middle/small sound reinforcement system.
3> UNPACKING DIGITAL SPEAKER PROCESSOR As a part of our system of quality control, every product is carefully inspected before leaving the factory to ensure flawless appearance. After unpacking, please inspect for any physical damage. Save the shipping carton and all packing materials, as they were carefully designed to minimize the possibility of transportation damage should the unit again require packing and shipping.
5> FRONT PANEL CONTROL FEATURES DIGITAL SPEAKER PROCESSOR Note: When the operation on front panel is locked(the LOCK indicator lights up ) or when connecting with PC, all the buttons is not available.
6> REAR CONNECTING FEATRUE 2 1 BGM F E ANALOG INPUT 1 D C DIGITAL SPEAKER PROCESSOR B ANALOG OUTPUT IN 2 6 3 1. Analog input terminals(IN-1,IN-2) Connector: XLR-3-31 1 GND 2 HOT 3 COLD Circuit: Electronic balanced circuit 2 1 Maximum input level:+20dBu 3 BGM SWITCH USB A RS485 OUT ~ AC IN 5 7 4 5. Control interface (standard USB port; support USB2.0) 2. Analog output termainals (A.B.C.D.E.
7> DISPLAY AND OPERATIOIN 1 Beta Three INPUT A 2 B DIGITAL SPEAKER PROCESSOR OUTPUT C D E F RECALL /ENTER COMP LIMITER IN-1 LIMITER IN-1 LIMITER IN-1 LIMITER IN-1 LIMITER IN-1 LIMITER IN-1 PROGRAM OVER OVER IN-2 OVER IN-2 OVER IN-2 OVER IN-2 IN-2 OVER IN-2 STATUS REMOTE/ID -6 -6 HF -6 HF -6 HF -6 HF OVER -6 -10 -10 MF -10 MF -10 MF -10 MF -20 -20 LF -20 LF -20 LF -20 -40 -40 SLF -40 SLF -40 SLF -40 HF -6 HF -10 MF -10 MF LF -
DIGITAL SPEAKER PROCESSOR 7.2 Indications and operation at LOCK To assure the use security by using an external computer(need to install control software of this processor), you can disable RECALL and REMOTE/ID operation with the unit, and then LOCK indicator lights up. You can operate without using an external computer to LOCK and release LOCK of the unit To LOCK 1). Turn off the power, 2). Turn on the power with keeping pressing UP button.(Sound is not output), 3).
DIGITAL SPEAKER PROCESSOR 7.5 Changing remote ID RECALL /ENTER UP DOWN RECALL /ENTER RECALL /ENTER REMOTE ID is preset at factory to 01. It can only be changed by operating from the panel: 1). Press DISPLAY button. Then REMOTE/ID indicator lights up and currently selected number displays set number displays, 2). Press UP or DOWN button repeatedly until the number you want appears. When you keep pressing them. The number gains or loses continuously, 3).
8> BUILT-IN SIGNAL PROCESSING DIGITAL SPEAKER PROCESSOR Signal Processing Block and procedure Chart ( go to 13 for reference). 8.1 input signal selecting block Select the combination of 2 analog channels ( IN1+IN2) and 2 digital channels ( IN1,IN2). 8.2 Master channel processing block 1). 11-band parametric equalizer EQ Type : (parametric equalizer type): Select one of Peaking/ bandpass/hi-shelf/lo-shelf/notch; Frequency : Adjustable in a range of 20Hz-20kHz, at 1/12 oct steps and from 121 points.
DIGITAL SPEAKER PROCESSOR 3). 3-band PEQ It offers 3-band PEQ for each output channel. Each parameter of 3-band PEQ is same as the PEQ of master channel processing block. 4). Channel Level Adjustable in 0.5dB steps over a range of oo -- +12.0dB. 5). Peak Limiter. Include Instantaneous waveform transformation type peak limiter in each channel. It can be set over a range of -24.0dBFs+2dBFs, OFF at 0.5dB steps. When signal reaches the limiting level, the limiter indicator is lit.
9> SYSTEM CONTROL SOFTWARE DIGITAL SPEAKER PROCESSOR This facility offers a mult-functional software control panel, which controls Max 50 equipments, and it equips lots of relative documents and allow users to put into practice concretely and quickly. 9.1 How to get this software The software is stored in the disc. of course, you can also down load the latest version of this software and more our company's optimize collocated files and practical useness. 9.
DIGITAL SPEAKER PROCESSOR 9.4 Using of the software When you finish the installation , run the controlling software and it will display the following page: 9-10 8 14 3 15 4 13 5 6 12 11 7 1 2 1). Display of status: Device ID. Program ID, Serial Port, 2). Indication of communication between this facility and computer: It displays OK normal communication, or ERROR for unmoral, 3). By different colors to identify the 13th curve of frequency response, 4). Device list, 2 times press No.
DIGITAL SPEAKER PROCESSOR 8). Program Operation Menu (effective only on line), after click, if choose see the following interface: after listing(Press Press Confirm program List order, then you can Stop List during the listing, the Program List will end )show: , then Show: Red Marks on the right of button, Show no operation. Protection: If set Protection ,the program can not be revised or covered.
DIGITAL SPEAKER PROCESSOR Recall Lock: Prohibit/ Permit to transfer the program via the panel key, if set program on the Panel ,and even can not transfer the program.. rohibit ,you can not see the Delete: the program protected will not be deleted Recall: Press the Recall order, will implement the operation of Transferring Program, and set the choosing program as the current using program. Stop List: Stop List Order only will be used in implementing List Program.
DIGITAL SPEAKER PROCESSOR 9). Save the current configuration program to file, and click to show the following interface: 10). Open the program file in the computer, and click to show the following interface: Choose the file, and press Open Button 11). Signal processing procedure ,Function Module, Parameter Adjustment range 11.
DIGITAL SPEAKER PROCESSOR 11.2 Delay Adjustment Interface Right corner is the Delay Adjustment Interface, if change the delay time, and the interface shows the delay distance accordingly(Sound speed=340m/s). 11.3 PEQ Adjustment Interface You can set PEQ Open/ Close and Link Attention: Link setting is also effective to Enter Channel Gain. Only press the button ,which show the Filter Curve accordingly, you can adjust the parameter ( Filter Tyye, Central Frequency,Q/Bandwidth, Gain/Level).
DIGITAL SPEAKER PROCESSOR 11.4 Input Channel Gain Adjustment Interface: 11.5 Input Channel Silence , press Mute , and turn red to show the state of Mute, otherwise , it is no Mute. 11.6 Output Channel Crossover setting Interface: 1 2 The above part is High Pass Filter ( cut low frequency), the under part is Low Pass Filter (cut high frequency ).
DIGITAL SPEAKER PROCESSOR 11.7 Output Channel Peak Limit Adjustment Interface Adjustment Range :-24.0db +2.0db,OFF, 0.5db for each step. 11.8 Output Channel Mute ,setting same as the INPUT CHANNEL. 12). Current output channel sound source choosing ( Choosing IN-1,IN-2,OR IN-1+IN-2) 13). Frequency Response Curve showing range, Show the PEQ curve of the main channel IN-1,IN-2 and the Output Channel, and the curve of the HPF / LPF . 14). Click the button with mouse and then show the following interface.
DIGITAL SPEAKER PROCESSOR 15). Default configure adjustment: when it is in the off line status, click the button for showing the following interface: Select the default configure file which need to adjust, click APPLY , for returning to the main interface. At the time, the parameter of the controller did not change. Click the command for login. Select download configure to controller. The parameter of controller will update after successful login, Audio process will be effective.
10> FREQUENTLY QUESTIONS SOLVING DIGITAL SPEAKER PROCESSOR 10.1 Audio relevant question Disconnect Check the power cord is connected well or not? And the power button on the front panel is turn on or not? Panel button operation error Check the lock button on the panel is flashing or not. And unit is locked status or not. No Sound output Check the input/output is silent or not? The plus of input/output is weak or not? Check the selection sound source of each output channel.
11> TECHNICAL SPECIFICATION DIGITAL SPEAKER PROCESSOR Analog input Port Input impedance Max input power A/D conversion : : : : Balanceable 6.35 mike socket (BGM signal) and XLR-3-31 input socket 10k +20dBu Frequency 64kHz, 24bits Analog output Port Output impedance Load impedance Max output level : : : : Balanceable XLR-3-32 output socket 47 600 +20dBu Analog characteristics Frequency response S/N Ratio Distortion+noise System min delay Remote control port : : : : : 20Hz-20kHz(+0.3/-0.
12> INSTALLATION RECORD Installation record Worker Agent DIGITAL SPEAKER PROCESSOR Tel: Tel E-mail: Address System description(equipment, engineer request and its relevant information): DEVICE program No.
DIGITAL SPEAKER PROCESSOR Input channel A: Sound source IN1 IN2 IN1+IN2,output plus dB phase normal contrary output delay parameter equal filter 1, filter type centre frequency Q value/wide parameter equal filter 2, filter type centre frequency Q value/wide parameter equal filter 3, filter type centre frequency Q value/wide Crossover setting low filter type Pressure limit value Input channel B: Sound source IN1 frequency dBFS mute IN2 low filter type open IN1+IN2,output plus dB fre
13> BLOCK DIAGRAM -IN1- Delay PEQ DIGITAL SPEAKER PROCESSOR Mute Gain select sound source for each channel -IN1-IN2-IN1+IN2- -IN2- Delay PEQ Mute Gain HpfLpf PEQ Gain Limiter Mute -A Delay HpfLpf PEQ Gain Limiter Mute -B Delay HpfLpf PEQ Gain Limiter Mute -C Delay HpfLpf PEQ Gain Limiter Mute -D Delay HpfLpf PEQ Gain Limiter Mute -E Delay HpfLpf PEQ Gain Limiter Mute -F Function drawing Input Sound source selection input dynamic indicator A/D Delay
Beta three User Manual C-2600U DIGITAL SPEAKER PROCESSOR www.elderaudio.
