MOON Halogen PR-2035H This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, 511430 China http://www.pr-lighting.
INDEX SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS XLR CONNECTORS CONNECTING CONTROLLER WITH PROJECTORS 5-PIN AND 3-PIN CONVERSION DMX TERMINATOR SETTING UNIT’ S START ADDRESS DMX CONTROL CHANNEL FUNCTIONS SETUP OPTIONS TO SET THE DMX START ADDRESS MASTER/SLAVE SYNCHRO MODE STAND-ALONE MODE CHANGING GOBOS LUBRICATION MAINTENANCE KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES 3 4 4 5 5 5 5
SAFE USAGE OF THE PROJECTOR The following points are important for safety as well as for the smooth installation and performance of the unit When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for Indoor use only, IP20. Use only in dry locations.
INSTALLING THE PROJECTOR This unit has been designed to be hung. Mount the bracket provided on the body of the projector by 2 M8 knobs provided, then suspend the projector via its bracket using a M12 size bolt and a nut. When you want to adjust the angle of the body of the projector, you only loosen the two M8 knobs carefully and then adjust the angle of the body. After finishing that, it is recommended that you don’ t forget to retighten the two knobs.
POWER SUPPLY - MAINS Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector is supplied separately so that they may be individually switched on and off. It is recommended that the green/yellow must be earthed correctly.
5-PIN AND 3-PIN CONVERSION MOON uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should convert 5-pin plug / socket into 3-pin socket / plug as shown below. DMX TERMINATOR In the Controller mode or Master/Slave mode, the DMX output has to be connected with a DMX terminator at the last fixture in the chain. This prevents electrical noise from disturbing and corrupting the DMX control signals.
DMX CONTROL CHANNEL FUNCTIONS The MOON uses 7 channels with standard DMX 512 protocol. They are listed in the following table.
OPERATION SETUP OPTIONS - PROJECTOR CONFIGURATION To browse through the various Setup Options, press the FUNC button consecutively. There are 11 option codes (1~9 and A, b), each code has a specific function. The functions provided are listed in the following table.
TO SET THE DMX START ADDRESS The display shows the DMX start address after the projector is switched on (if you have already set the DMX start address and saved it, the screen will display the last setting). Press the UP or DOWN buttons to select the required DMX start address in the display. Confirm your choice by pressing the ENTER button. In Stand-Alone mode, the DMX start address can be set at random. In the Controller and Master/Slave mode, the DMX start address must be set correctly.
CHANGING GOBOS Carefully lift off the upper cover by undoing the 4 M4 screws. Using a small screwdriver remove the gobo retaining spring. Insert the gobo into position, and then insert the retaining spring. Mount the cover again and retighten the 4 M4 screws. NOTE: It is recommended to add a little adhesive, such as high temperature silicon sealant, to hold securely the retaining spring inside the gear.
TROUBLESHOOTING PROBLEM RESOURCE The projector does not start The projector switches on but does not answer to commands The projector only functions intermittently The beam appears dim Projection with halo Defecting projection Check the fuse on the socket is blown or not. Check if the lamp is good or not. Check the projector is correctly configurated. Check the XLR cable is good. Check the fan is working and not dirty. Check the lamp is not at the end of its life. Check the optics are clean.
ELECTRICAL DIAGRAM 12/14 Moon-halogen manual.
COMPONENT ORDER CODES PART NO. REMARK TRANSFORMER THERMOSTAT FAN LAMP MOTOR 1 (COLOUR-WHEEL) MOTOR 2 (GOBO-WHEEL) MOTOR 3 (SHUTTER) MOTOR 4 (TILT) MOTOR 5 (PAN) MOTOR 6 (GOBO ROTATION) OPTICAL-COUPLE IC1 U1~U6 U7 U8 U9 U10 U11 U12 U13 U14 NAME 040020036 190010054 030060008 100040001 230V/50Hz 95℃/10A DC12V/0.
PR LIGHTING LTD. Yingbin Road, Dashi, Panyu, Guangzhou, China Post-Code: 511430 TEL: 020-8478-1888 FAX: 020-8478-6023 P/N: 321010141 Last Revision: 13:09:2003 14/14 Moon-halogen manual.