PILOT 1200 WASH PR2901 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. No. 571, Yingbin Road, Dashi Panyu, Guangzhou, 511430 China http://www.prlighting.
INDEX SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS DMX TERMINATOR SETUP OPTIONSPROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS FUNCTIONS DISPLAY DMX CONTROL CHANNEL FUNCTIONS LED DISPLAY CHANGING BELTS MAINTENANCE LUBRICATION KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES 3 4 4 5 5 6 6 6 7 9 10 10 11 11 11 12 13 14 15 Please note that as part of our ongoing commitment to continuous
SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the unit. Should there be any damage caused by transportation, consult your dealer and do not use the unit. The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
INSTALLING THE PROJECTOR SAFETY CORDS (2PCS) SAFETY CORD WARNING To pass 2 SAFETY CORDS through 4 HOLES for safety! HOLE HANDLES (2PCS) 4 HOLES FOR SAFETY CORD PASSING THROUGH WARNING 256 CLAMPS (2PCS) SAFETY CORD To pass 2 SAFETY CORDS through 4 HOLESfor safety! HOLE 106 Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp.
POWER SUPPLY MAINS Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on or off. IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards.
DMX TERMINATOR In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
Press the button FUNC , it will return to the upper menu one by one. FUNCTIONS DISPLAY SET ADDR. (Default: 001) ADDR. 001 RESET MENU RESET OR NOT CONFIG. MENU SET DMX EXT. CHANNEL (Default :ON) DMX EXT. CHANNEL ENABLED DMX EXT.
DISPLAY MENU(Default: ON) LCD OF PANEL DISPLAY MODE LCD IS ON LCD IS OFF AFTER DELY LCD IS DARK INFORMATION MENU DISPLAY LAMP'S USING TIME OR SET TO 0 DISPLAY LAMP'S USING TIME SET TO 0 OR NOT DISPLAY PROJECTOR'S USING TIME (CANNOT RESET) DISPLAY PROJECTOR'S USING TIME DISPLAY TEMPERATURE DISPLAY MAIN PCB'S TEMPERATUER DISPLAY DRIVER PCB Ⅰ'S TEMPERATURE DISPLAY DRIVER PCB Ⅱ'S TEMPERATURE DISPLAY PAN&TILT DRIVER PCB'S TEMPERATURE DISPLAY HEAD'S TEMPERATUER RESERVED DISPLAY PROGRAM VERSION DISPLAY MAIN PCB'S
DMX CONTROL CHANNEL FUNCTIONS The PILOT 1200 WASH uses 14 DMX channels. They are listed in the following table.
5 6 Pan Tilt 7 CYMCyan 8 CYMYellow Reverse rotation speed 10 Pan rotation Tilt rotation Cyan enter gradually Cyan from light to dark Stop Cyan from dark to light Yellow enter gradually Yellow from light to dark Stop Yellow from dark to light 250255 000255 000255 000127 128187 188197 198255 000127 128187 188197 198255 9 CYMMagenta 10 Effect Wheel 11 12 13 Pan & Tilt Speed Pan Fine Tilt Fine Control (when ext.
LED DISPLAY Green: Red: Both ON: Flash in turn: ON——DMX signal OK or Slave; OFF——No DMX signal; Flash——DMX error; Medium flash——Menu mode; Fast flash——software, cpu error; Address mode, Master mode. CHANGING BELTS Pan’s belts Free 2 screws on Pan assembly’s maintenance door and open the door; change the belts; close the door and fasten the screws. SCREWS Tilt’s belts The common users replacing the belts is not recommended.
TROUBLESHOOTING PROBLEM The projector switch on doesn’t The lamp comes on but the projector doesn’t respond to the controller POSSIBLE CAUSE The power supply is not present The lamp doesn’t work Wrong DMX configuration and/or start address Defective DMX cable The projector only functions intermittently Defective projection The fan has failed The projected image appears to have a halo Installation of the lamp is not correct Dust or grease contamination on the optics.
TECHNICAL DATA VOLTAGES: 200/220/230/245V AC, 50Hz or 60Hz POWER CONSUMPTION: 1380W LAMP: Type: PHILIPS MSR 1200 SA/DE or OSRAM HMI 1200 W/S Colour Temperature: 6000ºK Socket: SFc104, double ends Manufacturers Rated Lamp Life: 750 Hours COLOURS: Linear CYM colour mixing system from 0100% with macro function 1 colour wheel with 5 Dichroic colours plus white bicolour and bidirectional rainbow effects, linear and nonlinear colour shifting EFFECTS: White, 1 CTO (6000°K3200°K), 1 frost and 1 fresnel lens DIMM
ELECTRICAL DIAGRAM 14/16 Pilot 1200 wash EN.
COMPONENT ORDER CODES NAME TRANSFORMER THERMOSTAT CAPACITOR BALLAST IGNITOR LAMP FUSE PAN&TILT DRIVE BELT FAN IN BODY FAN ON THE REAR COVER FAN IN BASE PAN MOTOR TILT MOTOR CYMMAGENTA MOTOR CYMYELLOW MOTOR ZOOM MOTOR CYMCYAN MOTOR STROBE MOTOR IRIS MOTOR EFFECT WHEEL PAN&TILT DRIVE PCB MOTOR DRIVER PCB I MOTOR DRIVER PCB Ⅱ DIGITAL PCB POWER PCB PART NO.
PR LIGHTING LTD. No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, China PostCode: 511430 TEL: +86208478 1888 FAX: +86208478 6023 P/N: 321010231 Last Revision: 07: 05: 2006 16/16 Pilot 1200 wash EN.