PILOT 575 PR-2575 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, 511430 China h t t p : / / w w w . p r- l i g h t i n g .
INDEX SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS DMX TERMINATOR SETUP OPTIONS-PROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS FUNCTIONS DISPLAY REPLACING GOBOS REPLACING BELTS DMX CONTROL CHANNEL FUNCTIONS MAINTENANCE LUBRICATION KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES CHANGING THE OPERATION FREQUENCY 3 4 4 5 5 6 6 6 7 9 9 10 15 15 15 15 17 19 20 21 Please note that as part
SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
INSTALLING THE PROJECTOR SCREWS (1PCS PER CLAMP) SAFETY CORD WARNING To pass 2 SAFETY CORDS through 4 HOLES for safety! HOLE RETAINERS (2PCS PER CLAMP) WARNING SAFETY CORD To pass 2 SAFETY CORDS through 4 HOLES for safety! HOLE 4 HOLES FOR SAFETY CORD PASSING THROUGH 256 SAFETY CORD (2PCS) CLAMPS (2PCS) HANDLES (2PCS) 106 Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp.
POWER SUPPLY - MAINS Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.
DMX TERMINATOR In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
/22 OPTN CNFG Mode menu, “Enter”access MOdE Option menu, “Enter”access Configuration menu, “Enter” access RST? Reset menu, “Enter”access RST “Enter”access “Enter”access ON T\IN “Enter”access COLR “Enter”access “Enter”access LAMP P\IN “Enter”access “Enter”access “Down”, “Up” option; “Enter” confirm “Down”, “Up” option; “Enter” confirm “Enter” confirm; “Fun”abort Operation CTRL HRES STAT SLAV MSTR dMX 001 (DMX) Address menu, “Enter”access AddR nd 2 Operation 1 level st
/22 Pilot 575 Manual_ Last Revision_En.doc st Debug menu ,“Enter ”access Information menu, “Enter” access Operation rd th “Enter”access dRV1 SET VER “Enter” access “Enter” access “Enter” access MSTR TEM P Display digital driver PCB’ s temp.
REPLACING GOBOS Lock Tilt. Free 2 latch catches on the cover and slip off the front cover. You could see the structure as shown in the above figure. For gobos replacement on the rotated gobo wheel: take an appropriate tool to tug up spring and take out the rotating gobo with its holder; tug the head of retaining spring up and engage your another hand to take the retaining spring out; take the gobo out; fit a new gobo and fit the retaining spring; fit the lampholder.
DMX CONTROL CHANNEL FUNCTIONS The PILOT 575 uses 19 DMX channels. They are listed in the following table.
6 Tilt rotation 000-255 Tilt rotation from 0 to 270º 7 Focus 000-255 Linear adjust iris from near to far Zoom 000-050 051-101 102-152 153-203 204-255 Clear Angle 1(wide) Angle 2(narrow) CTB CTO 8 000-016 9 10 Colour Wheel 1 017-024 025-032 033-040 041-048 049-056 057-064 065-072 073-080 081-088 089-096 097-104 105-112 113-120 121-127 128-133 134-139 140-145 146-151 152-157 158-163 164-169 170-175 176-181 182-187 188-195 196-201 202-207 208-213 214-219 220-225 226-231 232-237 238-243 244-249
Colour Wheel 2 11 12 Rotating Gobo Wheel Gobo Rotation 017-024 025-032 033-040 041-048 049-056 057-064 065-072 073-080 081-088 089-096 097-104 105-112 113-120 121-127 128-133 134-139 140-145 146-151 152-157 158-163 164-169 170-175 176-181 182-187 188-195 196-201 202-207 208-213 214-219 220-225 226-231 232-237 238-243 244-249 250-255 000-043 044-085 086-128 129-170 171-212 213-255 000-120 121-127 128-135 136-143 144-151 152-159 White/colour filter 1 Colour filter 1 Colour filter 1/colour filter 2 Colou
Prisms 14 Prism Rotation 15 Pan & Tilt Speed (extended function) 160-167 168-175 176-183 184-191 192-199 200-207 208-215 216-223 224-231 232-239 240-247 248-255 000-051 052-102 103-153 154-204 205-255 000-120 121-127 128-135 136-143 144-151 152-159 160-167 168-175 176-183 184-191 192-199 200-207 208-215 216-223 224-231 232-239 240-247 248-255 (Rotating gobo) clockwise rotation in speed 6 (Rotating gobo) clockwise rotation in speed 7 (Rotating gobo) clockwise rotation in speed 8 000-255 Adjust Pa
16 17 18 19 Pan Fine (16Bit) (extended function) Tilt Fine (16Bit) (extended function) Gobo Rotation Fine (extended function) Control (when extended functions are invalid, shift this channel to 15th channel.
MAINTENANCE If the projector’ s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once, aged lamps run to the extremity of their life might explode.
The beam appears dim -Dust or grease contamination on the optics. -The lamp is at the end of its life components. Check the optics is clean. Replace with a new lamp of the specified type and rating. LIGHT OUTPUT 22°( lux) 19°( lux) 12°( lux) 4m 2m 0m 2m 8600 11270 7500 2150 2817 1875 950 1250 830 530 700 460 340 450 300 5m 3m 1m 12°19°22° 1m 3m 4m 5m DISTANCE (m) 0 5 10 15 20 25 12° DIAMETER (m) 0 1.05 2.1 3.1 4.4 5.2 19° DIAMETER (m) 0 1.6 3.3 5.0 6.6 8.
TECHNICAL DATA VOLTAGES: 100/120/200/220/230/245V AC, 50Hz or 60Hz to order POWER CONSUMPTION: 780W LAMP: Type: Philips MSR 575/2 discharge lamp Colour Temperature: 7200ºK Socket: GX9.
SIZES: 18/22 Pilot 575 Manual_ Last Revision_En.
/22 0V (100/120/200V/220V/240V) Transformer 230V ELECTRICAL DIAGRAM Pilot 575 Manual_ Last Revision_En.
COMPONENT ORDER CODES NAME TRANSFORMER THERMOSTAT CAPACITOR BALLAST IGNITOR LAMP PAN&TILT DRIVE BELT1, 2, 3, 4 FANS 1,2,3,4 PART NO. REMARK 040030053 040030052 040030051 190010054 140010043 040070059 040090035 100050017 290151221 030060035 030040089 030040092 030040093 030040094 030040095 030040096 220/230V 100/120V 200/240V KSD020 95℃/10A/250V 70µF/370V 230V/50-60Hz, 575W 575~1200W 3~5KV MSR 575W/2 HTD459-3M-6 KDE2409PTB-6 24VDC 23HS2039L Φ6.35x25 (4PCS) 16HY7001-16L Tr6.
CHANGING THE OPERATION FREQUENCY To be carried out by qualified engineers only The power input settings of the PILOT 575 may be changed to suit the supply in your area that the unit is to be operated. The voltage and frequency are pre-set at the factory and marked on the exterior of the unit. Any error or mistake in setting the voltage or frequency of the projector may seriously damage the unit.
PR LIGHTING LTD. No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, China Post-Code: 511430 TEL: +86-20-8478 1888 FAX: +86-20-8478 6023 P/N: 321010226 Last Revision: 13:04:2004 22/22 Pilot 575 Manual_ Last Revision_En.