PLANET PR-222R This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, 511430 China h t t p : / / w w w . p r- l i g h t i n g .
INDEX SECTION PAGE SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR 4 FITTING THE LAMP 4 POWER SUPPLY – MAINS 5 OPERATION 5 STAND-ALONE MODE 6 XLR CONNECTORS AND TERMINATOR 6 MASTER/SLAVE SYNCHRO MODE 7 CONTROLLER MODE - DMX OPERATION 8 DMX CONTROL CHANNEL FUNCTIONS 9 MAINTENANCE 10 KEEPING THE PROJECTOR CLEANING 10 TROUBLESHOOTING 10 ELECTRICAL DIAGRAM 11 TECHNICAL DATA 12 Please note that as part of our ongoing commitment to continuous product development, specificati
SAFE USAGE OF THE PROJECTOR The following points are important for safety as well as for the smooth installation and performance of the unit. When unpacking and before disposing of the package check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. Keep the package well for your possible future transportation. The projector is for Indoor use only, IP20. Use only in dry locations.
INSTALLING THE PROJECTOR Mount the bracket provided on the body of the projector by 2 M6 knobs provided, then suspend the projector via its mounting bracket using a M12 size bolt and a nut. When you want to adjust the angle of the body of the projector, you only loosen the two knobs carefully and then adjust the angle of the body. After finishing that, it is recommended that you don’ t forget to retighten the two knobs.
POWER SUPPLY - MAINS Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector is supplied separately so that they may be individually switched on and off. It is recommended that the green/yellow conductor must be earthed correctly.
SETUP OPTIONAL CODE CHOICE Y N Y N Y N Y N 1 2 3 4 5 6 Y N 7 8 9 A B FUNCTION Pan inversion enable-Pan is inverted Pan inversion disable-Pan is norma Tilt inversion enable-Tilt is inverted Tilt inversion disable-Tilt is normal Sound activation enable Sound activation disable Automatic programmes enable Automatic programmes disable Reserved for possible future development Reserved for possible future development Reset enable Reset disable Reserved for possible future development Reserved for possible fu
5-PIN AND 3-PIN CONVERSION PLANET uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should convert 5-pin plug / socket into 3-pin socket / plug as shown below. DMX TERMINATOR In the Controller mode or Master/Slave mode, the DMX output has to be connected with a DMX terminator at the last fixture in the chain. This prevents electrical noise from disturbing and corrupting the DMX control signals.
In the Master/Slave mode, you may run the master via the auto programmes having been set in the master or via sound activation through MIC inside the master, and the slaves will run synchronously with the master. In the Master/Slave mode, when the master is a combining of setup 3 (sound activation) and 4 (auto programmes), the projectors will run auto programmes. During operation, you can easily differentiate between the master and the slaves since the master’ s DMX output without connecting any cable.
DMX CONTROL CHANNEL FUNCTIONS The PLANET uses 6 channels with standard DMX 512 protocol. They are listed in the following table.
MAINTENANCE If the projector’ s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once, old lamps run to the extremity of their life can explode.
TECHNICAL DATA Power supply: Optional: AC230V/50Hz AC200V/60Hz Power consumption: 300W at 220V Lamp: MSD 250W discharge lamp Electric strength: 1.5KV Insulating resistance: >2MΩ Channels: 6 channels Signal: Standard DMX 512 Control mode: Sound activation, Auto programmes, Controller Running mode: Stand-Alone mode, Master/Slave synchro mode, Controller mode Colours: 11 dichroic colours plus white Gobos: 11 gobos plus white Strobe: Adjustable from 1 ~ 7 F.P.S Beam coverage: 8.
ELECTRICAL DIAGRAM 12/14 planet manual.
COMPONENT ORDER CODES NAME TRANSFORMER IGNITOR BALLAST THERMOSTAT FAN LAMP CAP MOTOR 1 (COLOUR-WHEEL) MOTOR 2 (GOBO WHEEL) MOTOR 3 (SHUTTER) MOTOR 4 (TILT) MOTOR 5 (PAN) IC1 U1~U6 U7 U8 PART NO.
PR LIGHTING LTD. Yingbin Road, Dashi, Panyu, Guangzhou, China Post-Code: 511430 TEL: 020-8478-1888 FAX: 020-8478-6023 P/N: 321010101 Last Revision: 19:03:2003 14/14 planet manual.