SOLO 1200 PR-2902 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, 511430 China h t tp : / / w w w . p r - l i g h t i n g .
INDEX SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS DMX TERMINATOR SETUP OPTIONS-PROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS FUNCTIONS DISPLAY REPLACING GOBOS CHANGING BELTS DMX CONTROL CHANNEL FUNCTIONS LED INDICATION MAINTENANCE LUBRICATION KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES 3 4 4 5 5 6 6 6 7 9 9 10 13 14 14 14 14 15 16 17 Please note that as part of our ongoing comm
SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
INSTALLING THE PROJECTOR SAFETY CORD (2PCS) SAFETY CORD WARNING To pass 2 SAFETY CORDS through 4 HOLES for safety! CLAMPS (2PCS) HOLE RETAINERS HANDLES (2PCS) 4 HOLES FOR SAFETY CORD PASSING THROUGH 256 (2PCS PER CLAMP) SAFETY CORD W ARNING To pass 2 SA FETY CORDS t hrough 4 HOLES for safety! HOLE 106 Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp.
POWER SUPPLY - MAINS Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.
DMX TERMINATOR In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
FUNCTIONS DISPLAY SET ADDR. (Default: 001) ADDR. 001 RESET MENU RESET OR NOT CONFIG. MENU SET DMX EXT. CHANNEL (Default : ON) DMX EXT. CHANNEL ENABLED DMX EXT.
DISPLAY MENU(Default : ON) LCD OF PANEL DISPLAY MODE LCD IS ON LCD IS OFF AFTER DELY LCD IS DARK INFORMATION MENU DISPLAY LAMP'S USING TIME OR SET TO 0 DISPLAY PROJECTOR'S USING TIME RESET OR NOT DISPLAY PROJECTOR'S USING TIME OR SET TO 0 DISPLAY PROJECTOR'S USING TIME DISPLAY TEMPERATURE DISPLAY MAIN PCB'S TEMPERATUER DISPLAY DRIVER PCB Ⅰ 'S TEMPERATURE DISPLAY DRIVER PCB Ⅱ 'S TEMPERATURE DISPLAY PAN&TILT DRIVER PCB'S TEMPERATURE RESERVED DISPLAY PROGRAM VERSION DISPLAY MAIN PCB'S PROGRAM VER.
REPLACING GOBOS Lock Tilt. Loosen 4 screws of the front cover, you will see rotated gobo wheel and fixed gobo wheel. (As shown in the above figure.) For gobos replacement on the rotated gobo wheel: take an appropriate tool to tug up spring and take out the rotating gobo with its holder; tug the head of retaining spring up and engage your another hand to take the retaining spring out; take the gobo out; fit a new gobo and fit the retaining spring; fit the holder.
DMX CONTROL CHANNEL FUNCTIONS The SOLO 1200 uses 18 DMX channels. They are listed in the following table.
033-040 041-048 049-056 057-064 065-072 073-080 081-088 089-096 097-104 105-112 113-120 121-127 128-133 134-139 140-145 10 Rotated Gobo Wheel 11 Gobo Rotation 146-151 152-157 158-163 164-169 170-175 176-181 182-187 188-195 196-201 202-207 208-213 214-219 220-225 226-231 232-237 238-243 244-249 250-255 000-043 044-085 086-128 129-170 171-212 213-255 000-120 121-127 128-135 136-143 144-151 152-159 160-167 168-175 176-183 184-191 11/18 Colour filter 1/colour filter 2 Colour filter 2 Colour filter 2/colou
13 14 15 16 17 18 Prisms Prism Rotation Pan & Tilt Speed （Extended function） Pan Fine (16Bit) （Extended function） Tilt Fine (16Bit) （Extended function） Gobo Rotation Fine （Extended function） Control （when extended functions are invalid, shift this channel to 15th channel.
right operation is: turn it off---cool down---push the slide bar to turn it on. LED INDICATION Green: ON——DMX signal OK or Slave; OFF——No DMX signal; Flash——DMX signal error; Red: Flash medium——Setting menu mode ; Flash fast——Software or CPU fault ; MAINTENANCE If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced.
TROUBLESHOOTING PROBLEM The projector doesn’t switch on The lamp comes on but the projector doesn’t respond to the controller The projector only functions intermittently POSSIBLE CAUSE -The power supply is not present -The lamp doesn’t work -Wrong DMX configuration and/or start address - Defective DMX cable -The fan has failed Defective projection -The lens is broken -Dust or grease on lenses The projected image appears to have a halo -Installation of the lamp is not correct -Dust or grease contaminati
TECHNICAL DATA VOLTAGES: 200/220/230/240V AC, 50Hz or 60Hz to order POWER CONSUMPTION: 1400W LAMP: Type: PHILIPS MSR 1200 SA/DE Or OSRAM HMI 1200W/S Colour Temperature: 6000ºK Socket: GY22, single end Manufacturers Rated Lamp Life: 750 Hours COLOURS: 1 colour wheels, 6 dichroic colours plus white each wheel Adjustable speed with rainbow effect COLOUR TEMPERATURE CORRECTION: 1 colour temperature corrective filters GOBOS: Rotated gobo wheel 5 interchangeable gobos+white, indexical, bidirectionally rotatable i
SOLO 1200 TILT ENCODE DMX-SENS2 DMX-SENS1 VCC VCC GND GND SENS5 SENS6 TILT-Encoder PAN-Encoder PAN2 D B C A SENS1 SENS2 MOTOR4 TILT1 TILT2 HALL 1-2 View of mark side HALL 1-1 View of mark side MOTOR5 PAN ENCODE TILT1 Encoder motor View side of no axletree SENS3 SENS4 SLAVE #1 PCB Encoder Side MOTOR3 PAN2 No encoder motor View side of no axletree MOTOR2 PAN1 Encoder motor View side of no axletree HALL 1-3 View of mark side DMX-SENS2 DMX-SENS1 VCC VCC GND GND MOTOR1 MOTOR6 DMX-IN DMX
COMPONENT ORDER CODES NAME TRANSFORMER THERMOSTAT CAPACITOR BALLAST IGNITOR LAMP PART NO.
PR LIGHTING LTD. No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, China Post-Code: 511430 TEL: +86-20-8478 1888 FAX: +86-20-8478 6023 P/N: 321010223 Last Revision: 07:05:2006 18/18 SOLO 1200 EN.
