SOLO 250 PR-2255 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, 511430 China h t t p : / / w w w . p r- l i g h t i n g .
INDEX SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS SETUP OPTIONS-PROJECTOR CONFIGURATIN TO SET THE DMX START ADDRESS DMX CONTROL CHANNEL FUNCTIONS STAND-ALONE MODE & MASTER/SLAVE MODE CHANGING THE GOBOS LUBRICATION MAINTENANCE KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES CHANGING THE OPERATION VOLTAGE AND/OR FREQUENCY 3 4 4 5 5 6 7 8 9 9 9 10 10 10 11 12 13 14 Please note that as part o
SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for Indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids.
INSTALLING THE PROJECTOR The projector should be mounted via its bracket using 2 M12 bolts. The bracket itself attaches to the underside of the projector with 4 M8x25 bolts provided in the package. Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure to which you are attaching the projector is secure and is able to support a weight of 18Kg for each SOLO 250.
POWER SUPPLY - MAINS Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off. IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards. Power consumption of the SOLO 250 is 400W.
5-PIN AND 3-PIN CONVERSION SOLO 250 uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should convert 5-pin plug / socket into 3-pin socket / plug as shown below. DMX TERMINATOR In the Controller mode or Master/Slave mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. Which prevents electrical noise from disturbing and corrupting the DMX control signals.
TO SET THE DMX START ADDRESS PROJECTOR DMX START ADDRESS Each SOLO 250 must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start address is the channel number from which the projector starts to “listen”to the digital control information being sent out from the controller. The SOLO 250 has 10 channels, so set the No. 1 projector’ s address 001, No. 2 projector’ s address 011, No. 3 projector’ s address 021, No.
DMX CONTROL CHANNEL FUNCTIONS The SOLO 250 uses 10 DMX channels. They are listed in the following table.
STAND-ALONE MODE & MASTER/SLAVE MODE STAND-ALONE MODE To operate the projector without connecting a controller, enable a combination of setup options 4 and 5, the projector will run in Stand-Alone mode with automatic programmes (effect 1 or 2) depending on the options that have been selected. See the section on “Setup Options – Projector Configuration”for full details of the available combinations.
MAINTENANCE If the projector’ s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once, old lamps run to the extremity of their life can explode. If the projector does not function, check the fuses on the power socket of the projector.
TECHNICAL DATA VOLTAGES: 100/120/200/220/230/240V AC, 50Hz or 60Hz To Order. POWER CONSUMPTION: 400W @ 220V LAMP: Type: MSD 250W discharge lamp. Colour Temperature: 6700ºK Socket: GY9.5 (Single end) Manufacturers Rated Lamp Life: 2000 Hours COLOURS: 9 Dichroic colours plus white GOBOS: 7 interchangeable, rotating gobos, with 4 extra spare gobos. Gobo diameter: 26.9mm Gobo image diameter: 22mm PRISM: 1 x 3 Facet, Bi-directionally rotating prism. FOCUS: DMX controlled focus.
LIGHT OUTPUT ELECTRICAL DIAGRAM 12/16 solo 250 manual_last revision_en.
COMPONENT ORDER CODES NO. PART NO. REMARK TRANSFORMER THERMOSTAT CAPACITOR BALLAST THERMOSTAT IGNITOR LAMP FAN FAN MOTOR MOTOR MOTOR(2pcs) MOTOR MOTOR(4pcs) MOTOR IC IC 040030301 190010065 140010045 20V 50W / 230V 300W 040070053 230V/50-60Hz, 250W/3.
CHANGING THE OPERATION VOLTAGE AND/OR FREQUENCY To be carried out by qualified engineers only The power input settings of the SOLO 250 may be changed to suit the supply in the area where the unit is operated. The voltage and frequency is pre-set at the factory and will be marked on the exterior of the unit. Any error or mistake in setting the frequency or voltage of the projector may seriously damage the unit.
/16 solo 250 manual_last revision_en.
PR LIGHTING LTD. No. 571 Yingbin Road, Dashi, Panyu, Guangzhou, China Post-Code: 511430 TEL: +86-020-84781888 FAX: +86-020-84786023 P/N: 321010085 Last Revision: 06:03:2004 16/16 solo 250 manual_last revision_en.