Manual

ManualsBrandsOmnitron Systems Technology ManualsCommunicationFlexCenter 200

Omnitron Systems Technology, Inc. 1

27 Mauchly #201, Irvine, CA 92618 (949) 250-6510 Fax: (949) 250-6514

FlexCenter

™

200

Auto-Sensing

Dual Speed 10/100 and 100 Stackable

Ethernet Hubs

User Manual

12 Omnitron Systems Technology, Inc.

SPECIFICATIONS

 Protocol: IEEE 802.3, 10Base-T, 100Base-Tx, 100Base-Fx

 Interface Connectors:

UTP: (12/24) RJ45 pins 1-2, 3-6 active

Fiber Optic: (1) SC or ST

 Cable Types:

UTP, 10Base-T: EIA/TIA 568, Category 3, 4, or 5

UTP, 100Base-Tx: EIA/TIA 568, Category 5

Fiber, Multimode (MM): 50/125, 62.5/125, 100/140 um

Fiber, Single-Mode (SM): 9/125 um

 Supported Distances:

UTP: 100 m / 328 ft.

MM, Extended: 2 km / 1.2 mi.

SM, Extended: 25 km / 15 mi.

SM, Long Haul (LH): 58 km / 35 mi.

 Indicators:

Hub:

Power: LED (1), Yellow (10/100) or Green (100), power applied

Activity 10: LED(1), Green, activity detected

Collision 10: LED (1), Yellow, collision detected

Activity 100: LED(1), Green, activity detected

Collision 100: LED (1), Yellow, collision detected

Link / Partition: LED (12/24), Green, per port: device detected / port partitioned

Port Speed: LED (12/24), Green, per port: 10 / 100 / Searching

100Fx and 10/100Tx Modules:

Data Received: LED (1), Green, data received

Link / Speed: LED (1), Green / Yellow, device detected and 10/100 speed

Duplex Mode: LED (1), Green / Yellow, Full-Duplex / Half-Duplex

Collision: LED (1), Yellow, collision detected

 Switches:

Hub:

UTP Crossover: Straight / Crossed

Stack Control: Base / Stack

Port Access Control: 6/12 Switches, 2 per 4 ports: Auto-Sensing / 100Base-Tx / 10Base-T

100Fx Module:

Duplex Mode: Full / Half-Duplex

10/100Tx Module:

UTP Crossover: Straight / Crossed

Auto-Sensing Mode: Auto-Sensing / Manual

Duplex Mode: Full-Duplex / Half-Duplex

Speed Control: 100Base-Tx / 10Base-T

 Dimensions / Weight: W:19.0"xD:8.0"xH:1.75" / 7 lb.

 Power: 110 / 230 VAC, 50 / 60 Hz

 Temperature: 0 to 40 degrees C

Humidity: 0-90% (non-condensing)

TECHNICAL SUPPORT

For assitance in installing this product, contact Omnitron’s Technical Support Department:

Phone: (949) 250-6510, Fax: (949) 250-6514

Address: Omnitron Systems Technology, Inc.

27 Mauchly, #201

Irvine, CA 92618, USA

Email: support@omnitron-systems.com

URL: www.omnitron-systems.com

Summary of content (6 pages)

PAGE 1
2 Omnitron Systems Technology, Inc. Omnitron Systems Technology, Inc. 1 SPECIFICATIONS Protocol: IEEE 802.3, 10Base-T, 100Base-Tx, 100Base-Fx Interface Connectors: UTP: (12/24) RJ45 pins 1-2, 3-6 active Fiber Optic: (1) SC or ST Cable Types: UTP, 10Base-T: EIA/TIA 568, Category 3, 4, or 5 UTP, 100Base-Tx: EIA/TIA 568, Category 5 Fiber, Multimode (MM): 50/125, 62.5/125, 100/140 um Fiber, Single-Mode (SM): 9/125 um Supported Distances: UTP: 100 m / 328 ft. MM, Extended: 2 km / 1.2 mi.
PAGE 2
Omnitron Systems Technology, Inc. Safety Considerations Warning The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron Systems Technology, Inc. Omnitron Systems Technology, Inc. 11 Application 7.
PAGE 3
10 Omnitron Systems Technology, Inc. Omnitron Systems Technology, Inc. 3 FlexCenter 200 Auto-Sensing Dual Speed 10/100 and 100 Stackable Ethernet Hubs User Manual GENERAL DESCRIPTION Application 5. Single Wiring Closet / Multiple Hubs This application depicts a single-wiring-closet-based network. It is a typical stacking application of the FlexCenter 200. In this case six hubs are stacked, accommodating up to 150 stations (144 ports plus six modules).
PAGE 4
Omnitron Systems Technology, Inc. The hub detects and displays per-segment activity (green LED) and collisions (yellow LED) for Ethernet and Fast Ethernet segments. The FlexCenter features a special uplink Port 1 RJ45 connector. This uplink connector is equipped with a crossover switch that can switch between the receiving and transmitting wire pairs. This feature eliminates the need for a “crossed cable” which is otherwise required for connection between hubs.
PAGE 5
8 Omnitron Systems Technology, Inc. b. When using in a stack, connect the stack cables “out” to “in” and set the first unit’s Stack Control Switch to the “Base” position. All other stack units should be set to the “Stack” position. c. Plug the power cord into the FlexCenter 200 and the other side to the appropriate AC outlet. d. Plug any Ethernet 10Base-T or 100Base-Tx workstations into the RJ45 connectors. The corresponding Link LED should turn ON. e. Connect port 1 to a workstation or another hub.
PAGE 6
Omnitron Systems Technology, Inc. Function Position Description Auto-Sensing / Manual mode: AN/MN Up Auto-sensing mode enabled. Down Manual mode enabled. Forced Full-Duplex / Half-Duplex (effective when in Manual mode): FD/HD Up Forced Full-Duplex (when connecting to a switch or a station with full-duplex capability). Down Forced Half-Duplex (when connecting to a hub or a station with half-duplex capability). Forced Fast Ethernet / Ethernet (effective when in Manual mode): 100/10 Up Forced Fast Ethernet.