® BEDIENUNGSANLEITUNG USER'S MANUAL MODE D'’EMPLOI MANUAL DEL USUARIO DJ-40 Classic-Edition Vinyl Flash-Edition Silver-Edition © COPYRIGHT Nachdruck verboten! All rights reserved! Réproduction interdite! Prohibida toda reproducción! Für weiteren Gebrauch aufbewahren! Keep this manual for further needs! Gardez ces instructions pour des utilisations ultérieurs! Guarde este manual para posteriores usos.
Frontpanel OMNITRONIC POWER ON OFF 0 10 MIN MIC LEVEL OFF MAX CROSSFADER CURVE GAIN ON TALKOVER LINE 1 PHONO 1 MIN 1-2 GAIN LINE 3 2-1 PHONO 2 LINE 2 MAX CUE MIX CUE SPLIT LINE 4 CROSSFADER FLIP L/R CH-1 Battle-Mixer 10 10 DJ-40 +6 +6 +3 +3 0 5 0 5 -3 10 10 0 CH-1/ CH-2 -6 -12 -12 dB 5 5 0 0 -3 -6 -20 0 CH-2 -20 0 10 0 10 CUE LEVEL CUE MASTER CH-1 CH-2 CUE MIXING 10 5 0 CH-1 CH-2 0 MIC 5 CROSSFADER 10 HEADPHONES
Faceplate MIC HEADPHONES Rearpanel CAUTION Typ/Type: OMNITRONIC DJ-40 Spannungsversorgung/ Power supply: 10 V AC, 1 A ~ Gesamtanschlusswert/Power consumption: 10 VA Read manual before use. To prevent electrical fire and shock hazard, do not expose this appliance to moisture. Risk of electric shock! Do not open! There are no serviceable parts inside the device. Vor Gebrauch Anleitung lesen. Gerät vor Feuchtigkeit schützen.
MULTI-LANGUAGE-INSTRUCTIONS Inhaltsverzeichnis Table of contents Sommaire Contenido 1. EINFÜHRUNG ............................................................................................................................................... 5 2. SICHERHEITSHINWEISE ............................................................................................................................. 5 3. BESTIMMUNGSGEMÄSSE VERWENDUNG ...................................................................................
BEDIENUNGSANLEITUNG DJ-40 DJ-Battle-Mixer Lesen Sie vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung, Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen - entsprechend qualifiziert sein - diese Betriebsanleitung genau beachten. 1. EINFÜHRUNG Wir freuen uns, daß Sie sich für ein OMNITRONIC DJ-40 Mischpult entschieden haben.
Dieses Gerät hat das Werk in sicherheitstechnisch einwandfreiem Zustand verlassen. Um diesen Zustand zu erhalten und einen gefahrlosen Betrieb sicherzustellen, muss der Anwender unbedingt die Sicherheitshinweise und die Warnvermerke beachten, die in dieser Gebrauchsanweisung enthalten sind. Unbedingt lesen: Bei Schäden, die durch Nichtbeachtung dieser Bedienungsanleitung verursacht werden, erlischt der Garantieanspruch. Für daraus resultierende Folgeschäden übernimmt der Hersteller keine Haftung.
Verwenden Sie niemals Reinigungsspray, um die Fader zu reinigen. Reinigen Sie das Gerät niemals mit Lösungsmitteln oder scharfen Reinigungsmitteln, sondern verwenden Sie ein weiches und angefeuchtetes Tuch. Soll das Gerät transportiert werden, verwenden Sie bitte die Originalverpackung, um Transportschäden zu vermeiden. Beachten Sie bitte, dass eigenmächtige Veränderungen an dem Gerät aus Sicherheitsgründen verboten sind.
5. GERÄTEÜBERSICHT 5.
(6) CROSSFADER FLIP-SCHALTER Mit dieser Funktion können Sie die Crossfader-Kanäle umkehren. Bei der Schalterstellung "1-2" liegt auf der linken Crossfader-Seite Kanal 1, in der Position "2-1" liegt auf der linken Crossfader-Seite Kanal 2. (7) CROSSFADER Mit dem CROSSFADER wird ein Kanal mit dem anderen gemischt. Befindet sich der Crossfader in der Mittelstellung, werden beide Kanäle gehört. (8) MIC LEVEL-REGLER Mit dem MIC LEVEL-Regler können Sie den Mikrofonpegel einstellen.
(17)HEADPHONES-BUCHSE An diese Buchse können Sie Kopfhörer mit einer Impedanz von 8 bis 600 Ohm anschließen. 5.3 Rückseite CAUTION Typ/Type: OMNITRONIC DJ-40 Spannungsversorgung/ Power supply: 10 V AC, 1 A ~ Gesamtanschlusswert/Power consumption: 10 VA Read manual before use. To prevent electrical fire and shock hazard, do not expose this appliance to moisture. Risk of electric shock! Do not open! There are no serviceable parts inside the device. Vor Gebrauch Anleitung lesen.
7. AUSTAUSCHEN DES CROSSFADERS Wenn Sie einen kompletten Ersatz-Crossfader gekauft haben, gehen Sie wie folgt vor: • Ziehen Sie den Faderknopf ab. • Entfernen Sie die 2 äußeren Schrauben an der Faderplatte. • Heben Sie den Crossfader mit Faderplatte heraus und ziehen Sie den Anschlussstecker ab. • Schließen Sie den neuen Crossfader an und befestigen Sie ihn mit den Schrauben am Gerät. Bei der Design-Version kann die Faderplatte des Ersatz-Crossfaders nicht verwendet werden.
OPERATING INSTRUCTIONS DJ-40 DJ-Battle-Mixer For your own safety, please read this user manual carefully before you initial start-up. All persons involved in the installation, operation and maintenance of this device have to: - be qualified - follow the instructions of this manual 1. INTRODUCTION Thank you for having chosen an OMNITRONIC DJ-40. If you follow the instructions given in this manual, we can assure you that you will enjoy this device for many years. Unpack your OMNITRONIC DJ-40.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. Important: Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems. Always plug in the power unit least.
Please use the original packaging if the device is to be transported. Please consider that unauthorized modifications on the device are forbidden due to safety reasons! Never remove the serial barcode from the device as this would make the guarantee void. If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, etc. 4.
5. DESCRIPTION OF THE DEVICE 5.
(6) CROSSFADER FLIP-SELECTOR With this function, you can invert the Crossfader-channels. In the position "1-2" channel 1 is on the left Crossfader-side, in the position "2-1" channel 1 is on the right Crossfader-side. (7) CROSSFADER Mixes the signals of one channel with another. If the crossfader is in the center-position, both channels can be heard. (8) MIC LEVEL-CONTROL With the MIC LEVEL control, you can adjust the microphone volume.
5.3 Rearpanel CAUTION Typ/Type: OMNITRONIC DJ-40 Spannungsversorgung/ Power supply: 10 V AC, 1 A ~ Gesamtanschlusswert/Power consumption: 10 VA Read manual before use. To prevent electrical fire and shock hazard, do not expose this appliance to moisture. Risk of electric shock! Do not open! There are no serviceable parts inside the device. Vor Gebrauch Anleitung lesen. Gerät vor Feuchtigkeit schützen. Gefahr! Gerät nicht öffnen! Im Geräteinneren befinden sich keine zu wartenden Teile.
7. REPLACING THE CROSSFADER Instructions for replacing the crossfader: • Remove the fader knob. • Remove the two outer screws on the fader-panel. • Take the fader out and unplug the connection-cable. • Connect the new fader and fix it in the device. The fader-panel of the replacement-crossfader cannot be used for the Design-version. In order to exchange the fader-panels, additionally unscrew the 2 inner screws and exchange the two fader-panels. 8.
MODE D'EMPLOI DJ-40 DJ-Battle-Mixer Pour votre propre sécurité, veuillez lire ce mode d'emploi avec attention avant la première mise en service. Toute personne ayant à faire avec le montage, la mise en marche, le maniement et l’entretien de cet appareil - doit être suffisamment qualifiée - est priée de suivre strictement les instructions de service suivantes. 1. INTRODUCTION Nous vous remercions d'avoir choisi un OMNITRONIC DJ-40.
Cet appareil a quitté les ateliers dans un état irréprochable. Pour assurer un bon fonctionnement, sans danger, l'utilisateur doit suivre les instructions contenues dans ce mode d'emploi. Attention: Tout dommage occasionné par la non observation des instructions de montage ou d'utilisation n'est pas couvert par la garantie. Le bloc d'alimentation doit toujours être branché en dernier lieu. Assurez-vous que l'interrupteur ON/OFF de l'appareil est en position OFF avant d'effectuer ce branchement.
Ne nettoyez pas l'appareil avec des produits de nettoyages trop puissants ou abrasifs. Utilisez un chiffon doux, humide. Si vous deviez transporter l'appareil, utilisez l'emballage d'origine pour éviter tout dommage. Notez que pour des raisons de sécurité, il est interdit d'entreprendre toutes modifications sur l'appareil. Il est interdit de retirer le code barre de l'appareil. Ceci annulerait toute garantie.
5. DESCRIPTION DE L'APPAREIL 5.
(6) SELECTEUR CROSSFADER FLIP Avec cette fonction, vous pouvez reverser les canaux du Crossfader. Dans la position "1-2", le canal 1 est à la gauche du Crossfader, dans la position "2-1", le canal liegt 2 est à la gauche du Crossfader. (7) CROSSFADER Pour mixer un canal avec l’autre. Lorsque le crossfader se trouve au milieu, vous entendrez les deux canaux. (8) RÉGULATEUR MIC LEVEL Le régulateur MIC LEVEL vous permet de régler l'intensité sonore du microphone.
5.3 Dos de l'appareil CAUTION Typ/Type: OMNITRONIC DJ-40 Spannungsversorgung/ Power supply: 10 V AC, 1 A ~ Gesamtanschlusswert/Power consumption: 10 VA Read manual before use. To prevent electrical fire and shock hazard, do not expose this appliance to moisture. Risk of electric shock! Do not open! There are no serviceable parts inside the device. Vor Gebrauch Anleitung lesen. Gerät vor Feuchtigkeit schützen. Gefahr! Gerät nicht öffnen! Im Geräteinneren befinden sich keine zu wartenden Teile.
7. REMPLACEMENT DU CROSSFADER Procédez de la manière suivante: • Retirez la tête du fader. • Retirez les deux vis extérieurs à la plaque du fader. • Retirez maintenant le crossfader et débranchez. • Connectez le crossfader de rechange et fixez-le à la table de mixage. La plaque du crossfader de remplacement ne peut être utilisée pour l'édition de dessin. Pour remplaçer la plaque du fader, retirez les deux vis intérieurs et échanchez les plaques. 8.
MANUAL DEL USUARIO DJ-40 DJ-Battle-Mixer POR SU PROPIA SEGURIDAD, POR FAVOR LEA ESTE MANUAL DEL USUARIO DETENIDAMENTE ANTES DE LA CONEXIÓN INICIAL! Toda persona implicada en la instalación, manejo y mantenimiento de este aparato tiene que: -estar cualificada -seguir las instrucciones de este manual 1. INTRODUCCIÓN Gracias por haber elegido un OMNITRONIC DJ-40. Desembale su DJ-40. Antes de la puesta en marcha inicial, por favor asegúrese de que no hay daños causados durante el transporte.
Importante: Los daños causados por no hacer caso de las instrucciones de este manual del usuario no están sujetos a garantía. El proveedor no aceptará responsabilidad por ningún defecto o problema resultante. Siempre conectar la unidad de alimentación al final. Asegúrese de que el conmutador de alimentación está en la posición “OFF” antes de conectar el aparato a la red.
No utilice disolventes o detergentes agresivos para limpiar el aparato. Utilice mejor un paño suave y húmedo. ¡Por favor tenga en cuenta que por razones de seguridad las modificaciones no autorizadas del aparato están prohibidas! El código de barras de serie no debe ser quitado del aparato, en caso de que esto ocurra la garantía ya no es válida. Cuando el aparato será utilizado de un modo diferente como describido en este manual, ésto puede causar daños en el producto y la garantía expira.
5. VISTA GENERAL DEL APARATO 5.
(6) Selector Crossfader Flip Con está función , Vd. puede invertar los canales del Crossfader. En la posición "1-2" liegt el canal 1 está en la izquierda del Crossfader, en la posición "2-1" el canal 2 está en la derecha del Crossfader. (7) Crossfader Mezcla las señales de un canal con las de otro. (8) Regulador de nivel del micrófono Se puede ajustar el volumen del micrófono. (9) Selector de función “Talkover” Este selector tiene las funciones siguientes: OFF: el micrófono está desactivado.
5.3 Panel trasero CAUTION Typ/Type: OMNITRONIC DJ-40 Spannungsversorgung/ Power supply: 10 V AC, 1 A ~ Gesamtanschlusswert/Power consumption: 10 VA Read manual before use. To prevent electrical fire and shock hazard, do not expose this appliance to moisture. Risk of electric shock! Do not open! There are no serviceable parts inside the device. Vor Gebrauch Anleitung lesen. Gerät vor Feuchtigkeit schützen. Gefahr! Gerät nicht öffnen! Im Geräteinneren befinden sich keine zu wartenden Teile.
7. SUSTITUCIÓN DEL CROSSFADER Instrucciones para sustituir el Crossfader (cuando Vd. ha comprado un crossfader completo): • • • • Retirar el botón de fader Retirar los 2 tornillos exteriores del panel del fader Sacar el fader y desconectar el cable de conexión Conectar el nuevo fader y fijarlo en el aparato. Para la versión de diseño, Vd. no puede utilizar el panel de fader del crossfader de recambio. Para sustituir el panel de fader, también tiene que retirar los 2 tornillos interiores. 8.