User manual

Warning
The operating description in this Instruction Manual is for use by
qualified personnel only. To avoid electrical shock, do not perform any
servicing of this unit other than that contained in the operating
instructions, unless you are qualified and certified to do so by
Omnitron Systems Technology, Inc.
Warranty
This product is warranted to the original purchaser against defects
in material and workmanship for a period of TWO YEARS from the
date of shipment. A LIFETIME warranty may be obtained by the
original purchaser by REGISTERING this product with Omnitron
within 90 days from the date of shipment. TO REGISTER,
COMPLETE AND MAIL OR FAX THE ENCLOSED
REGISTRATION FORM. Or you may register your product on the
Internet at www.omnitron-systems.com. During the warranty period,
Omnitron will, at its option, repair or replace a product which is
proven to be defective.
For warranty service, the product must be sent to an Omnitron designated
facility, at Buyer’s expense. Omnitron will pay the shipping charge to
return the product to Buyer’s designated US address using Omnitron’s
standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper
or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized
modifications or tampering with equipment (including removal of
equipment cover by personnel not specifically authorized and certified
by Omnitron), or misuse, or operating outside the environmental
specification of the product (including but not limited to voltage, ambient
temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically
disclaims the implied warranties of merchantability and fitness for any
particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive
remedies. Omnitron shall not be liable for any direct, indirect, special,
incidental, or consequential damages, whether based on contract, tort,
or any legal theory.
Form: 040-08380-001N 12/12
BOARD MOUNTED DIP-SWITCHES
RFD
Down
4
3
2
1
BPOEN
LP
=
=
=
=
Remote Fault Detect Enable
Backplane Enable
Link Propagate/Link Segment
Flow Control Enable (PAUSE)
FLOWEN
Fig. 4 Board Mounted DIP-Switches
LINK MODES (SW4 and SW1)
The module supports multiple link modes for fault
detection and isolation. Link Segment should be used
for the initial installation of the module. Once installed
and operational, the link mode can be modified.
Link modes are controlled by DIP-switch 2 and 4.
SW2
(LP)
SW4
(RDF)
FUNCTION
DOWN DOWN Link Segment (LS)
UP DOWN Link Propagate (LP)
DOWN UP Remote Fault Detect + Link Propagate (RFD+LP)
UP UP Symmetrical Fault Detect (SFD)
“BPOEN” A and B Backplane Enable DIP-Switch
When the A and B Backplane Enable “BPOEN”
DIP-switch is in the UP position, both the A and B
backplane ports are enabled and connect to the
backplane to facilitate In-Band management. When
the “BPOEN” switch is in the DOWN position (factory
setting), both ports are disabled and disconnected from
the backplane.
“FLOWEN” Flow Control (PAUSE) DIP-switch
When the Flow Control “FLOWEN” DIP-switch is in the
UP position, flow control functionality is enabled. When
the module is configured for FDX, PAUSE functionality
is enabled. When the module is configured for HDX,
jam functionality is enabled. When flow control is
enabled, a port will generate either a pause or jam frame
when internal resources are not available to receive the
next incoming frame.
When the DIP-switch is in the DOWN position (factory
default), flow control is disabled.
LED INDICATORS:
LED COLOR DESCRIPTION
Power Yellow On - Power
Fiber FDx: Green On - Full-Duplex selected
F/O Link: Green On - Link
Rapid Blinking - activity
0.5Hz blinking - SFD error detected
UTP Auto: Green On - Auto-Negotiation enabled
UTP 100: Green On - 100 Mbps link
UTP 10: Green On - 10 Mbps link
UTP FDx: Green On - Full-Duplex detected
Blinking - Collision in HDx mode
UTP Link: Green On - Link
Rapid Blinking - activity
0.5Hz blinking - SFD error detected
MOUNTING AND CABLE ATTACHMENT:
iConverter modules are hot-swappable and can be
installed into any chassis in the
iConverter family.
1. Carefully slide the iConverter module into the
installation slot, aligning the module with the
installation guides.
NOTE: Ensure that the module is firmly seated
against the backplane.
2. Secure the module by securing the panel fastener
screw (attached to module) to the chassis front.
3. Attach the UTP port via a category 5 cable to a
100BASE-TX or 10BASE-T Ethernet device.
4. Attach the fiber port via an appropriate multimode
or single-mode fiber cable to a 100BASE-FX Ethernet
device. The
iConverter transmit (Tx) must attach to
the receive side on other device; the receive (Rx)
must attach to the transmit.
5. When using single-fiber (SF) media converter models,
the Tx wavelength on one end has to match the Rx
wavelength on the other. Note that based on this
guideline, the SF media converter models must be used
in pairs, such as the 8390-1 matched with the 8391-1.
Page 9
Page 10 Page 11
Page 12
Page 15
Page 16
Page 14
SPECIFICATIONS
Model Type 10/100
Protocols
100BASE-FX, 10BASE-T,
or 100BASE-TX
Frame Size
up to 1,536 bytes
UTP
Connectors
RJ-45
Fiber
Connectors
SC, ST, LC
Single-Fiber SC
Controls
UTP X-over,
LS/LP, RFD, SFD,
Auto/Man, 10/100, FDX/HDX,
Flow Control
LED Displays
Power,
F/O FDX/HDX, FO link activity,
Auto, FDX/HDX, 10, 100,
UTP link activity,
TECHNICAL SUPPORT:
For help with this product, contact our Technical Support:
Phone: [phone]
Fax: [phone]
Address: Omnitron Systems Technology, Inc.
140 Technology Dr.
Irvine, CA 92618 USA
E-mail: [e-mail]
URL: www.omnitron-systems.com
SPECIFICATIONS
Dimensions
W:0.850" x D:4.5" x H:2.8"
Weight
8 oz.
Compliance
UL, CE, FCC Class A,
NEBS Level 3
Power
Requirement
0.95A @ 3.3VDC (typical)
Temperature
Standard: 0 to 50º C
Wide: -40 to 60º C
Storage: -40 to 80º C
Humidity
5 to 95% (non-condensing)
Altitude
-100m to 4000m
MTBF (hrs)
1,050,000
Page 13