intelligent Lifestyle 2.
Important Notes for Getting Started We congratulate you on your purchase of the iMRS one magnetic resonance stimulation system. In combination with the Omnium1 control device, the iMRS one represents the latest development and application standard in the field of magnetic resonance stimulation systems for home use. The IMRS one is a wellness system for home use.
Table of Contents 1. Safety Instructions: Where You should be Careful.........................................4 1.1 Contra-indications..........................................................................................9 1.2 Side Effects...................................................................................................10 2. Intended Use..................................................................................................10 3. Possible Applications............................
1. Safety Instructions: Where You should be Careful If you feel dizzy, be careful when standing up! There are no negative reports on the application of Magnetic-Resonance-Stimulation anywhere in the world. However, for reasons of safety, we recommend that people with orthostatic problems (dizziness when getting up) get up very slowly and carefully after application.
checked to ensure that it will operate as intended when stored in this manner. The expansion of the magnetic field from the applicators will have largely abated at a distance of about 1.5 meters. People who are not receiving a session should remain outside the indicated range during the course of an application. We are legally obliged, in accordance with the EMC regulations to provide you with the following information.
Interference Immunity Tests IEC 60601 Test Level Compliance Level Electromagnetic Environment - Guidelines Discharge of static electricity (ESD) Acc. to IEC 610004-2 ± 6 kV contact discharge ± 8 kV air discharge ± 6 kV contact discharge ± 8 kV air discharge Floors should be made of wood or concrete or covered in ceramic tiles. If the floor is covered with synthetic material, the relative air humidity must be at least 30 %. Fast-transient interference test/ Bursts acc.
Guidelines and Manufacturer’s Declaration: Electromagnetic Stability Interference The iMRS one is intended for operation in an ELECTROMAGNETIC ENVIRONMENT as indicated below. The customer or iMRS user should ensure that it is operated in such an environment. Interference Immunity Tests IEC 60601 Test Level Compliance Level Electromagnetic Environment - Guidelines Conducted RF interference acc. to IEC 6100044-6 Radiated RF interference acc.
Recommended Safe Distances between Portable or Mobile RF Telecommunication Devices and the iMRS one The iMRS one is intended for operation in an ELECTROMAGNETIC ENVIRONMENT in which radio frequency interference is controlled.
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
For the following conditions, please consult your health care practitioners on the use of iMRS one system: Presence of tumors • • Serious cardiac arrhythmia • Acute attacks of hyperthyroidism • Extreme sensitivity to electromagnetic radiation 1. 2. Side Effects A light itching on the body or a warm feeling may be felt in the prevention use.
4. Scope of Delivery iMRS one Android software (Pre-installed on the Omnium1) OmniMat OmniPad D/A Converter 20-pin Cable OmniSpot Not included with the iMRS one basic set Operating Manual If one part should be damaged or missing, please contact your consultant at Swiss Bionic Solutions.
4.1 Control Unit The iMRS one will only function in connection with the Omnium1 control unit. The Omnium1 control device is included in the scope of delivery for all iMRS one sets available. You will find the operating instructions for the Omnium1 in the special manual that accompanies the control device.
5. Installation 1. Take the individual parts out of the packaging. Place the full-body applicator on a stable, even surface, such as on the floor, on a couch or under the mattress (but not box-spring mattresses) of your bed (pay attention to the intensity adjustment, please). Heavily shaped and soft furniture, such as a sofa, chair, very soft surfaces should be avoided, since the pressure load on uneven supports may lead to damage to the built-in copper coils. 2.
6. Activation After you have completely installed the system and checked the battery charge state, activate the iMRS one app by tapping the program icon (1) on the Omnium1 desktop (2). 2 1 Afterwards, the iMRS one initial screen will display the legally indicated contraindications. As soon as it has been acknowledged (by pressing ENTER), you will see the user interface for the iMRS one application.
7. 7. Saving and Loading Pre-set Parameters The iMRS one application provides you with the ability to save various users in advance. You can save all organ clocks with all time and intensity levels for each applicator in advance and load them as needed. 7.1 Saving In order to create a new user, tap on the “ interface and then tap “Users”. 1 2 Settings” button on the user 4 3 5 6 Tap the “Name” entry (4) and overwrite the placeholder.
If you have set all of the applicators, tap on “Save” (6) to save your entries permanently on the Omnium1. If you want to create another user, tap the “+” icon (2) above the list of users and repeat the process (in principle, any number of users desired can be created). If you created all of the users desired, you can tap “Back” (1) to return to the main screen for the iMRS one application. 7.2 Loading Choose the user, once the system has successfully been started. To do that, tap on the User icon (2).
8. Starting an Application Connect the D/A converter and the desired applicator (see Chapter 5, Installation) and start the iMRS one application (see Chapter 6, Activation). After the system has been successfully started, chose the desired application duration. To do so, tap the circle next to Timer (1) and set the desired application duration from 1 to 60 minutes. It can be set in steps of 1 minute.
9. 9. Quick Start Programs In addition to the parameters that can be manually set, the iMRS one application provides five pre-set quick start programs (exclusive with the full body applicator).
10.2 Factory Settings By tapping the “Reset Factory Settings” button, you can restore the iMRS one app to its delivery state. Note: all of the stored users will be deleted. 10.3 Users See Chapter 7, Saving and Loading Pre-set Parameters. 11. Updating Whenever your Omnium1 is connected to the internet (via WIFI), your iMRS one App automatically verifies, whether a new software version is available. In this case a notification appears on your screen. Please klick on „YES“ followed by clicking on „Install“.
applicator. The recommended threshold for harmlessness in low-frequency magnetic fields is 400 μT in accordance with the standard that preceded DIN 0848. Horizontally, the expansion of the magnetic field from the applicators will have largely abated at a distance of about 1.5 meters. This application can only be performed with the original full body applicator. If an applicator is not connected or the applicator is defective, an error message will appear on the Omnium1’s display.
Two solid copper coils have been built into the OmniSpot. The magnetic field not only works directly above the OmniSpot applicator, but also spreads itself out in all directions. The flux density of the pillow applicator is less than or equal to 120 μT at its highest intensity. The recommended threshold for harmlessness in low-frequency electromagnetic fields is 400 μT in accordance with the standard that preceded DIN 0848.
14. Maintenance & Error Messages The iMRS one system has been designed to be maintenance free. Potential Error Messages: Error Message Explanation DA Converter not working properly The D/A converter is defective. Low battery for DA convertor The battery is below the 5% charge state. Error Coil Open Loop There is a defect or broken wire in the applicator. Error No Applicator Connected An applicator has not been connected, or not been connected properly.
15. Identification & Technical Data 15.1 Identification Specification Plate for the iMRS one (D/A converter): iMRS one V1.
9 HF frequency None 10 Mode of use Continuous operation 11 Construction Portable device 12 Protection class II 13 Application part Type B 14 Type of moisture protection Covered device 15 Fuse between the primary and secondary power supplies Omnium1 Type BI20-180100-I power supply 16 Initial voltage at the applicator box Max.
2 Covering Artificial leather, disinfectble, do not roll or bend 3 Dimensions 57 x 29 x 3 cm 4 Cable length 2m OmniSpot Applicator 1 Coils 2 solid copper coils 2 Covering Artificial leather, disinfectble, do not roll or bend 3 Dimensions 39 x 16 x 2,5 cm 4 Cable length 2m Intensity Measures values in µT OmniMat whole body applicator Measures values in µT OmniPad pillow applicator Measures values in µT OmniSpot applicator Foot Abdomen Shoulder 0,27 0,22 0,09 0,35 0,65 10 1,3
Swiss Bionic Solutions Schweiz GmbH Schulhausstrasse 17 | 8834 Schindellegi, Schweiz Phone: +41 (62) 295 5951 | Fax: +41 (62) 295 5952 Email: ch@swissbionic.com Swiss Bionic Solutions Deutschland GmbH Biberacher Str. 87 | 88339 Bad Waldsee, Deutschland Phone: +49 (7524) 996 950 | Fax: +49 (7524) 996 9518 Email: de@swissbionic.com Swiss Bionic Solutions USA Inc. 12330 SW 53rd Street | Suite 703 & 704 | Cooper City | Florida 33330, USA Phone: +1 (954) 766 4153 | Fax: +1 (954) 766 4156 Email: us@swissbionic.
