INSTRUCTION MANUAL 使用说明书 #1 BY DESIGN Thank you for buying OMP HOBBY products.The M2 is the latest technology in Rotary RC mldels.Please read this manual carefully before assembling and flying the New M2 helicopter.
INTRODUCTION 前言 Thank you for buying OMPHOBBY Products. The M2 Helicopter is designed as an easy to use,full featured Helicopter R/C model capable of all forms of rotary flight. Please read the manual carefully before assembling the model, and follow all precautions and recommendations located within the manual. Be sure to retain the manal for future reference, routine maintenance, and tuning. The M2 is a new product developed by OMPHOBBY.
Precautions before use 使用前须知 FORBIDDEN 禁止 LOCATE AN APPROPRIATE LOCATION 远离障碍物及人群 R/C helicopters fly at high speed ,thus posing a certain degree of potential danger .Choose a legal flying field consisting of flat,smooth groumd without obstacles. Do not fly near buildings,high voltage cables ,or trees to ensure the safety of yourself,others and your model. For the first practice,please choose a legal flying field and can use a training skid to fly for reducing the damage .
EQUIPMENT REQUIRED FOR ASSEMBLY 自备工具 Cutter Knife 刀子 Philips Screw Drive 十字螺丝起子 Scissors 剪刀 Diagonal Cutting Pliers 斜口钳 Needle Nose Pliers 尖嘴钳 Hexagon Screw Driver 六角螺丝起子 Oil润滑油 CA瞬间胶 AB Glue AB胶 胶水使用方法 When you see the marks as below,please use glue or greae to ensure flying safety.
Specifications 参数规格 Specifications 参数配备 Lenght：422mm 机身长：422mm Height：140mm 机身高：140mm Main Blade：190mm 主旋翼长度：190mm Main Rotor Diameter：434mm 主旋翼直径：434mm Tail Rotor Diameter：88.9mm 尾旋翼直径：88.
step 1 步骤一 ! CAUTION 注意 For flights with high headspeed ,the inspection interval should be reduced to ensure flight safety. Obverse of bearing faces inside. 轴 开 内 止 轴 及横轴 属于飞行 转速飞行时，请缩 定期 Bearing-MR63ZZ 轴 (Ø3xØ6x2.5mm)x4 品，建 定期 数，以确保飞行安全。 及 换，高主旋翼 Bearing-MR63ZZ 轴 Ø3xØ6x2.5mm ase Gre Washer 主夹头轴 Thrust braring and washer for radial bearing are wear items,and thus should be inspected for replacement after every 20 flights. Thrust bearing0FM-6M 止 轴 -Ø3xØ6x2.8mm Ø3xØ4.4x1.
step 2 步骤二 Socket screw 内六角螺丝 M2.5x7mm Socket screw 内六角螺丝 (M2.5x7mm)x3 ! Motor Mount 电机固定 Socket screw 内六角螺丝 (M1.6x6mm)x2 Socket screw 内六角螺丝 (M1.7x8mm)x2 CAUTION 注意 Socket screw 内六角螺丝 (M1.6x4mm)x4 Spindle retaining ring 固定环 (Plane) (Inclined plane) 斜 Swashplate Phase plastic Panel 斜 胶相 Spindle retaining ring 固定环 Socket screw 螺丝M3X2.5 Main Motor 电机 Socket screw 内六角螺丝 M1.7x8mm Servo Mount set 机固定 Socket screw 内六角螺丝 M1.6x6mm Bearing-684ZZ (Ø4xØ9x4mm)x1 Socket screw 内六角螺丝 M1.
step 3 步骤三 Frame Rear carbon Reinforcement Plate set 机身后加 Socket screw 内六角螺丝 (M1.6x4mm)x6 Socket screw 内六角螺丝 (M1.7x4mm)x4 Socket screw 内六角螺丝 (M1.7x6mm)x2 Canopy Fixed Bolt 机 固定 Socket screw 内六角螺丝 M1.6x4mm Socket screw 内六角螺丝 M1.7x6mm Fuselage Lower Left Carbon Fiber Board set 机身 下 Socket screw 内六角螺丝 M1.7x4mm Fuselage lower Right Carbon Fiber Board set 机身 下 Flight Control Mounting Panel 飞控机身 胶固定 Battery phase panel 电 限 Socket screw 内六角螺丝 M1.
step 4 步骤四 Socket screw 柱头内 螺丝 M2x10mm-L4 Ball screws 球头螺丝 Washer 片 Ø2xØ3.5x0.3mm M2 Nut M2防 螺 Socket screw 柱头内 螺丝 M2x8mm Bearing 轴 5 Tilt tray bracket 倾斜盘 架 Pros and Cons auxiliary arm 螺距 臂 Pin Shaft 轴 5 Socket screw 柱头内 螺丝 (M2x8mm)x2 Swash plate 倾斜盘 Socket screw 柱头内 螺丝 (M2x10mm-L4)x1 Socket screw 柱头内 螺丝 (M2x4mm)x4 Washer 片(Ø2xØ3.5x0.3mm)x4 Washer 片(Ø2xØ3.5x0.4mm)x2 EN Washer 片 Ø2xØ3.5x0.4mm WWW.OMPHOBBY.
step 5 步骤五 Landing skid mount 固定 Landing Skids lock pad 机 罩 Landing skid Washer Ø1.6xØ3.5x0.4mm Socket screw 内六角螺丝 M1.6x8mm Socket screw 内六角螺丝 M1.6x4mm Socket screw 内六角螺丝 (M1.6x8mm)x4 Socket screw 内六角螺丝 (M1.6x4mm)x10 Socket screw 内六角螺丝 M1.6x4mm Socket screw 内六角螺丝 (M2x4mm)x4 Socket screw 内六角螺丝 M1.6x4mm Washer (Ø1.6xØ3.5x0.4mm)x4 O-ring 型 Socket screw 内六角螺丝 M1.6x4mm Side plate struts EN 10 WWW.OMPHOBBY.
step 6 步骤六 Tail Motor 电机 3K CF Vertical Stabilizer 3K 碳纤维垂直翼 Socket screw 内六角螺丝 M1.6x3mm Tail Boom inner Mount block 内 固定 Tail Motor Reinforcement Plate 电机固定 加 Tail Boom 尾管 Socket screw 内六角螺丝 (M1.6x3mm)x2 Socket screw 内六角螺丝 (M1.6x4mm)x3 Socket screw 内六角螺丝 M1.6x4mm Socket screw 内六角螺丝 M1.6x6mm Socket screw 内六角螺丝 (M1.6x6mm)x2 M2 Nut M2 螺 Hexagon socket head M2*14(9mm) 内六角螺丝 M2x14mm EN WWW.OMPHOBBY.
step 7 步骤七 Ball Joint Screw - L3 tooth Length 球头(Ø3.175x3-M1.6) Socket screw 柱头内 螺丝 (M1.6x4mm)x3 Servo Swing Arm 舵机摆臂 M1.6 Nut M1.6螺 Linkage Ball 球头(Ø3.175x3-M1.6)x1 Servo 全金属舵机 M1.6 Nut 螺 (M1.6)x1 Washer 片 Ø2xØ3.6x0.2mm Socket screw 头内 螺丝 M1.6x4mm Socket screw 柱头内 螺丝 M1.6x4mm Socket screw 柱头内 螺丝 M1.6x4mm Linkage Ball 球头(Ø3.175x3-M1.6)x2 Servo M1.6 Nut 螺 (M1.6)x2 全金属舵机 Socket screw 柱头内 螺丝 (M1.6x4mm)x6 M1.6 Nut M1.6螺 Ball Joint Screw - L3 tooth Length 球头(Ø3.175x3-M1.
step 8 步骤八 约10 Linkage rod CH2 Linkage rod CH2 约28.2mm 约28.2mmx3 Linkage rod Approx.28.2mmx3 CH3 Linkage rod CH3 CH1 Linkage rod CH1 Flight Control 飞控 Double-sided tape 胶 ! CAUTION 注意 Note:Fist,the double-sided damping rubber should be fully fitted with the receiver board, and then install the flight control.The flight control must be completely parallel to the fuselage to achieve the best flight performance. 注意 将 胶与 机 完全 合好，再安装飞控。飞控必 与机身完全 行，以 最佳的 飞行 。 EN WWW.OMPHOBBY.
step 9 步骤九 Socket screw 柱头内 螺丝 (M2x12mm-L4)x2 M2 Nut M2防 螺 (M2)x2 Screw sleeve M2螺丝 x2 Washer 横轴轴 片 (Ø2.1xØ10x0.3mm)x4 Socket screw 柱头内 螺丝 (M2x12mm-L4)x2 Screw sleeve M2螺丝 Washer 片 Ø2xØ10x0.2mm M2 Nut M2防 螺 Main Blade 主旋翼 Socket screw 柱头内 螺丝 (M1.6x6mm)x2 Tail Blade 尾桨 Socket screw 柱头内 螺丝 M1.6x6mm EN 14 WWW.OMPHOBBY.
step 10 步骤十 Batteries 电 EN WWW.OMPHOBBY.
step 11 步骤十一 Canopy 机 罩 EN 16 WWW.OMPHOBBY.
step 12 步骤十二 负 5V Data 3.3V 负 Data CH2 Antenna POWER 电源线 CH3 LED Light LED灯 CH1 BIND 对频按键 Main Motor 主电机线接口 Tail Motor 尾电机线接口 Flight Parameter Setting lntroduction 飞行参数设置说明 General Flight Model 一般飞行模式 Throttle 油门 5 60 4 60 3 60 2 60 1 0 IDLE 1 Model IDLE 1模式 Screw Pitch 螺距 100 Throttle 油门 Modes 模式 CH5 Screw Pitch 螺距 12° 5 65 100 65 5.5° 4 65 15 1.8° 3 65 -5 -0.6° 2 -20 -2.4° 1 Attitude mode /3D mode 姿态模式/3D模式 姿态模式 75-100 80 100 11° 50 5.
Spare parts picture-1 配件-1 Package: Hang tag +PE bag Model: OSHM2301 包装方式：吊卡+PE袋 配件编号: OSHM2301 Product name: Servo Mount set 配件名称: 舵机固定座组 Package: Hang tag +PE bag Model: OSHM2302 包装方式：吊卡+PE袋 配件编号: OSHM2302 Product name:Main Motor Mount set 配件名称: 主电机固定座组 Package: Hang tag +PE bag Model: OSHM2303 包装方式：吊卡+PE袋 配件编号: OSHM2303 Product name: Coaxiality mount 配件名称: 同心度保持架组 Package: Hang tag +PE bag Model: OSHM2304 包装方式：吊卡+PE袋 配件编号: OSHM2304 Product name: Carbon fiber middle frame 配件名称:机身中加强板 Package: Hang tag
Spare parts picture-2配件-2 Package: Hang tag +PE bag Model: OSHM2317W 包装方式：吊卡+PE袋 配件编号: OSHM2317W Product name: Main Motor set-Silver 配件名称: 主电机组（银色） Package: Hang tag +PE bag Model: OSHM2317O 包装方式：吊卡+PE袋 配件编号: OSHM2317O Product name: Main Motor set-Orange 配件名称: 主电机组（橙色） Package: Hang tag +PE bag Model: OSHM2014 包装方式：吊卡+PE袋 配件编号: OSHM2014 Product name: Servo Linkage Rod set 配件名称: 舵机连杆组 Package: Hang tag +PE bag Model: OSHM2318W 包装方式：吊卡+PE袋 配件编号: OSHM2318W Product name: Tail Motor Reinforcement Plate set-Si
Spare parts picture-3 配件-3 Package: Hang tag +PE bag Model: OSHM2323R 包装方式：吊卡+PE袋 配件编号: OSHM2323R Product name: Canopy set-Glamour Red 配件名称: 机头罩（魅力红） Package: Hang tag +PE bag Model: OSHM2324 包装方式：吊卡+PE袋 配件编号: OSHM2324 Product name: Phase Panel set 配件名称: 相位座组 Package: Hang tag +PE bag Model: OSHM2325 包装方式：吊卡+PE袋 配件编号: OSHM2325 Product name: battery lower panel set 配件名称: 电池仓下板组 Package: Hang tag +PE bag Model: OSHM2326 包装方式：吊卡+PE袋 配件编号: OSHM2326 Product name: Fuselage Carbon panel set 配件名称: 机身侧板组（竞速黄） Pa
Transmitter description-1 遥控器说明-1 Remote Control Power Light(Red) 遥控器电 （红 ） Remote Control Power Light(Blue) 遥控器 号 （ ） (MODEL 2) HOLD IDLE Attitude mode Manual mode Manual mode 手 手 式 式 式 D/R Throttle, Orientation 方 70% 85% 100% Front Back, Left Right 后 Flying Ring 吊 POWER-2 Helicopter Battery Indicator 直 机电 POWER-1 Remote Control Power Light(Red) 遥控器电 （红 ） Remote Control Power Light(Blue) 遥控器 号 （ ） (MODEL 1) HOLD IDLE Attitude mode Manual mode Manual mode 手 手 式 式 式 D/R Front Back, Orient
Transmitter description- 遥控器说明- (Product Model)产品型号：T6 (Diameters)外形尺寸长：L165*W98*H180 Handle 提手 (Radio Frequency)无线频率：2.413GHz--2.453 GHz (Transmit Power)发射功率：< 20 dBm (Weight)重量约：345g 5V <2A Charge Interface 充电接口 (Modulation Mode)调制方式：GFSK (Spread Spectrum Mode)扩频方式：FHSS (Working Voltage)工作电压：3.7V Coach Interface 教练接口 (Remote Distance)遥控距离：800m (Charge Interface)充电接口：Micro (Low Voltage Alarm)低电压报警：3.4V (Battery Type)电池类型：Lithium Polyer Battery (Battery Capacity)电池容规格：2500mAh 3.
Transmitter description-3 遥控器说明-3 SE-0: SE-1:手 式/Attitude mode 式/Manual mode SF-0: SF-1: SA: /None SD: SB-0: 式/Normal mode SB-1: 3D 式1/3D IDLE 1 SB-2: 3D 式2/3D IDLE 2 器 /Throttle ON /Throttle OFF /Timer clear -1 - emote sensin description o orro remote contro Zorro遥控器 遥 说明 EN WWW.OMPHOBBY.
Memo 备忘录 EN WWW.OMPHOBBY.
Zhuhai edge smart dirve technology Co., Ltd www.omphobby.
