EXPLORE INSTRUCTION MANUAL 使用说明书 #1 BY DESIGN Thank you for buying OMP HOBBY products.The M2EXP is the latest technology in Rotary RC mldels.Please read this manual carefully before assembling and flying the New M2EXP helicopter.
-EXPLORE INTRODUCTION 前言 Thank you for buying OMPHOBBY Products. The M2EXP Helicopter is designed as an easy to use,full featured Helicopter R/C model capable of all forms of rotary flight. Please read the manual carefully before assembling the model, and follow all precautions and recommendations located within the manual. Be sure to retain the manal for future reference, routine maintenance, and tuning. The M2EXP is a new product developed by OMPHOBBY.
Precautions before use 使用前须知 FORBIDDEN 禁止 -EXPLORE LOCATE AN APPROPRIATE LOCATION 远离障碍物及人群 R/C helicopters fly at high speed ,thus posing a certain degree of potential danger .Choose a legal flying field consisting of flat,smooth groumd without obstacles. Do not fly near buildings,high voltage cables ,or trees to ensure the safety of yourself,others and your model. For the first practice,please choose a legal flying field and can use a training skid to fly for reducing the damage .
-EXPLORE EQUIPMENT REQUIRED FOR ASSEMBLY 自备工具 Cutter Knife 刀子 Philips Screw Drive 十字螺丝起子 Scissors 剪刀 Diagonal Cutting Pliers 斜口钳 Needle Nose Pliers 尖嘴钳 Hexagon Screw Driver 六角螺丝起子 Oil润滑油 CA瞬间胶 AB Glue AB胶 胶水使用方法 When you see the marks as below,please use glue or greae to ensure flying safety.
135 Specifications 参数规格 408 70 400 Specifications 参数配备 Lenght:408mm 机身长:408mm Height:135mm 机身高:135mm Main Blade:173mm 主旋翼长度:173mm Main Rotor Diameter:400mm 主旋翼直径:400mm Tail Rotor Diameter:71.5mm 尾旋翼直径:71.
step 1 步骤一 Obverse of bearing faces inside. 轴承面凹开口朝内 ! CAUTION 注意 For flights with high headspeed ,the inspection interval should be reduced to ensure flight safety. e as Gre Ball Bearing-MR63ZZ 滚珠轴承(Ø3xØ6x2.5mm)x2 Ball Bearing-MR63 滚珠轴承(Ø3xØ6x2mm)x2 Thrust braring and washer for radial bearing are wear items,and thus should be inspected for replacement after every 20 flights. Flat bearing gasket 平面轴承垫片(Ø4xØ6x0.
-EXPLORE step 2 步骤二 倾斜盘塑胶相位座 Socket screw 圆柱头内六角螺丝 M2.5x7mm Spindle retaining ring 主轴固定环 Socket screw 基米螺丝M3X2.5 Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 ST1.7x8mm Motor Mount 主电机固定座 Steering gear mount 舵机固定座 Socket screw 圆柱头内六角螺丝 M1.6x6mm Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 ST1.7x8mm Main Motor 主电机 Bearing-684ZZ 滚珠轴承 (Ø4xØ9x4mm)x1 Concentricity retention column 主轴同心度保持柱 Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 (ST1.7x8mm)X2 Main Shaft 主轴 Socket screw 圆柱头内六角螺丝(M2.
-EXPLORE step 3 步骤三 Canopy Support 机壳固定柱 Rear reinforcing plate 机身后加强板 Socket screw 圆柱头内六角螺丝 M1.6x4mm Frame upper side panel 机身上侧板 Socket screw 圆柱头内六角螺丝 (M1.6x3mm)x4 Canopy Support 机壳固定柱 Socket screw 圆柱头内六角螺丝 (M1.6x4mm)x6 尾管固定座 Frame upper side panel 机身上侧板 Frame widening mount 机身加宽固定座 Rear reinforcing plate 机身后加强板 Socket screw 圆柱头内六角螺丝 M1.6x3mm Socket screw 圆柱头内六角螺丝 M1.6x3mm Socket screw 圆柱头内六角螺丝 M1.
-EXPLORE step 4 步骤四 Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 ST1.7x6 Socket screw 圆柱头内六角螺丝 M1.6x3mm Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 ST1.7x4 Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 ST1.7x6 飞控盒安装板 Socket screw 圆柱头内六角螺丝 M1.6x3mm Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 ST1.7x4 Frame upper side panel 底板 Socket screw 圆柱头内六角螺丝 (M1.6x3mm)x4 Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 (ST1.7x4)x4 Hexagon socket head tapping screw 圆柱头内六角自攻牙螺丝 (ST1.7x6)x2 WWW.OMPHOBBY.
-EXPLORE step 5 步骤五 Socket screw 圆柱头内六角螺丝 M2x10mm-L2.5 M2 Nut M2防松螺母 Washer 垫片 Ø2.1xØ3.6x0.2mm Flange bearing MF52ZZ 滚珠轴承 Ø2xØ5x2.5mm Copper sets 铜套Ø2.xØ3.9x2.2mm Main Pitch Control Arm 主螺距控制臂 Flange bearing MF52ZZ 滚珠轴承 Ø2xØ5x2.5mm Washer 垫片 Ø2.1xØ3.6x0.2mm Swash plate 倾斜盘 Socket screw 圆柱头内六角螺丝(M2x10mm-L2.5)x2 Washer 垫片(Ø2.1xØ3.6x0.2mm)x4 Flange bearing MF52ZZ 滚珠轴承(Ø2xØ5x2.5mm)x4 Copper sets 铜套(Ø2.xØ3.9x2.
-EXPLORE step 6 步骤六 Landing skid mount 脚架固定座 机头罩脚架防松垫 Hexagon socket head machine screw 圆柱头内六角机械螺丝 M1.6x8mm Socket screw 圆柱头内六角螺丝 (M1.6x3mm)x8 Landing skid 脚架 Hexagon socket head machine screw 圆柱头内六角机械螺丝 M1.6x8mm Socket screw 圆柱头内六角螺丝 (M1.6x8mm)x4 Socket screw 圆柱头内六角螺丝 M1.6x3mm Socket screw 圆柱头内六角螺丝 M1.6x3mm Socket screw 圆柱头内六角螺丝 M1.6x3mm EN WWW.OMPHOBBY.
-EXPLORE step 7 步骤七 Tail motor 尾电机 尾管内部固定块 Socket screw 圆柱头内六角螺丝 M1.6x3mm 尾电机固定座加强片 Socket screw 圆柱头内六角螺丝 M1.6x3mm Vertical wing 垂直翼 Socket screw 圆柱头内六角螺丝 (M1.6x3mm)x5 Socket screw 圆柱头内六角螺丝 M1.6x6mm Socket screw 圆柱头内六角螺丝 (M1.6x6mm)x2 Socket screw 圆柱头内六角螺丝 M1.6x4mm Socket screw 圆柱头内六角螺丝 (M1.6x4mm)x1 Socket screw 圆柱头内六角螺丝 (M1.6x12mm-L4)x2 Socket screw 圆柱头内六角螺丝 (半牙,牙长4) M1.6x12mm EN 12 WWW.OMPHOBBY.
-EXPLORE step 8 步骤八 Socket screw 圆柱头内六角螺丝 (M1.6x3mm)x2 Socket screw 圆头内十字机械牙螺丝 (M1.6x4)x1 Socket screw 圆头内十字螺丝 M1.6x4mm Linkage Ball 球头(Ø3.175x3-M1.6) 全金属齿轮/塑胶外壳舵机 M1.6 Nut Linkage Ball 球头(Ø3.175x3-M1.6)x1 M1.6螺母 Servo Arm 舵机摆臂 M1.6 Nut 螺母(M1.6)x1 Socket screw 圆柱头内六角螺丝 M1.6x4mm Socket screw 圆柱头内六角螺丝 M1.6x4mm Linkage Ball 球头(Ø3.175x3-M1.6)x2 Socket screw 圆头内十字机械牙螺丝 (M1.6x4)x2 全金属齿轮/塑胶外壳舵机 M1.6 Nut M1.6 Nut 螺母(M1.6)x2 Socket screw 圆柱头内六角螺丝 (M1.6x4mm)x4 M1.
-EXPLORE step 9 步骤九 约10mm 约28.2mm 连杆约28.2mmx3 CH1 Linkage rod CH1 连杆 Linkage rod Approx.28.2mmx3 CH3 Linkage rod CH3 连杆 CH2 Linkage rod CH2 连杆 Flight Control 飞控 Double-sided tape 双面胶 ! CAUTION 注意 Note:Fist,the double-sided damping rubber should be fully fitted with the receiver board, and then install the flight control.The flight control must be completely parallel to the fuselage to achieve the best flight performance. 注意:先将双面减震胶与接收机板 完全贴合好,再安装飞控。飞控必 须与机身完全平行,以达到最佳的 飞行效果。 EN 14 WWW.
-EXPLORE step 10 步骤十 Socket screw 圆柱头内六角螺丝 (M2x12mm-L4)x2 Socket screw 圆柱头内六角螺丝 (M2x12mm-L4)x2 M2 Nut M2防松螺母(M2)x2 Washer 垫片 Ø2.1xØ10x0.3mm Main Blade 主旋翼 M2 Nut M2防松螺母 Socket screw 圆柱头内六角螺丝 (M1.6x6mm)x2 Tail Blade 尾旋翼 Socket screw 圆柱头内六角螺丝 M1.6x6mm EN WWW.OMPHOBBY.COM 15 Washer 横轴轴承垫片 (Ø2.1xØ10x0.
-EXPLORE step 11 步骤十一 Battery mount 电池固定板 Hook and loop tape(hooked) 魔术粘(勾状) Hook and loop tape(fuzzy) 魔术粘(织毛状) Battery 电池 Hook and loop tape 魔术带 Align the sides of the panel with the fuselage bettery compertment slideay, then push it hard to hear a “click” to indicate that it is in place. 将电池板两侧对准机身电池仓导 轨,用力推到底听到“咔”一声 表示到位。 Battery latch position 电池卡扣位置 EN 16 WWW.OMPHOBBY.
-EXPLORE step 12 步骤十二 Canopy 机头罩 EN Canopy protector 机头罩橡胶固定圈 WWW.OMPHOBBY.
step 13 步骤十三 CH2 负极 5V Data 数据 3.3V 负极 Data 数据 MAIN MOTOR Antenna 天线 SET LED CH3 PITCH ELEV SPEED AILE AGILE GYRO TAIL MOTOR BIND CH1 EN 18 RUDD WWW.OMPHOBBY.
Spare parts picture-1 配件-1 Package: Hang tag +PE bag Model: OSHM2081 包装方式:吊卡+PE袋 配件编号: OSHM2081 Product name: Metal Main Rotor Housing set 配件名称: 主轴中心座组-EXP 适用机型: M2-EXP Package: Hang tag +PE bag Model: OSHM2082 包装方式:吊卡+PE袋 配件编号: OSHM2082 Product name: Plastics Main Rotor Holder set 配件名称: 主夹头组-EXP Package: Hang tag +PE bag Model: OSHM2083 包装方式:吊卡+PE袋 配件编号: OSHM2083 Product name: Croduct Phase Panel Set 配件名称: 相位座-EXP Package: Hang tag +PE bag Model: OSHM2084 包装方式:吊卡+PE袋 配件编号: OSHM2084 Product name: Servo
第20页 Spare parts picture-2 配件-2 Package: Hang tag +PE bag Model: OSHM2101 包装方式:吊卡+PE袋 配件编号: OSHM2101 Product name: Tail Screw Set(Green) 配件名称: 机头罩--绿色 适用机型: M2-EXP 装好胶套 Package: Hang tag +PE bag Model: OSHM2102 包装方式:吊卡+PE袋 配件编号: OSHM2102 Product name: Canopy Set(Yellow) 配件名称: 机头罩--黄色 Package: Hang tag +PE bag Model: OSHM2103 包装方式:吊卡+PE袋 配件编号: OSHM2103 Product name: Canopy Set(Charm Orange) 配件名称: 机头罩--橙色 适用机型: M2-EXP 装好胶套 适用机型: M2-EXP 装好胶套 Package: Hang tag +PE bag Model: OSHM2104 包装方式:吊卡+PE袋 配件编号:
Spare parts picture-3 配件-3 Package: Hang tag +PE bag Model: OSHM2002 包装方式:吊卡+PE袋 配件编号: OSHM2002 Product name: Feathering shaft set 配件名称: 横轴组 Package: Hang tag +PE bag 包装方式:吊卡+PE袋 Package: Hang tag +PE bag Model: OSHM2008 包装方式:吊卡+PE袋 配件编号: OSHM2008 Product name: FBL Pros and Cons linkage rod 配件名称: 主螺距控制臂组 Package: Hang tag +PE bag Model: OSHM2010 包装方式:吊卡+PE袋 配件编号: OSHM2010 Product name: Metal Main Rotor Housing set 配件名称: 主轴固定环组 适用机型: M2-EXP M2-2020 适用机型: M2-EXP M2-2020 适用机型: M2-EXP M2-2020 Package: Ha
Spare parts picture-4 配件-4 Package: Hang tag +PE bag Model: OSHM2052 包装方式:吊卡+PE袋 配件编号: OSHM2052 Product name: Flight Control Damping Shing Set 配件名称: 飞控减震贴组 Package: Hang tag +PE bag Model: OSHM2053 包装方式:吊卡+PE袋 配件编号: OSHM2053 Product name: Battery Magic Tape Set 配件名称: 电池魔术贴组 Package: Hang tag +PE bag Model: OSHM2054 包装方式:吊卡+PE袋 配件编号: OSHM2054 Product name: Pull Rod Head Set 配件名称: 拉杆头组 Package: Hang tag +PE bag Model: OSHM2055 包装方式:吊卡+PE袋 配件编号: OSHM2055 Product name: Futaba Satellite Receiver 配件名称: futaba
-EXPLORE Transmitter description-2 遥控器说明-2 (Product Model)产品型号:T6 (Diameters)外形尺寸长:L165*W98*H180 Handle 提手 (Radio Frequency)无线频率:2.413GHz--2.453 GHz (Transmit Power)发射功率:< 20 dBm (Weight)重量约:345g Charge Interface 充电接口 (Modulation Mode)调制方式:GFSK (Spread Spectrum Mode)扩频方式:FHSS (Working Voltage)工作电压:3.7V Coach Interface 教练接口 (Remote Distance)遥控距离:800m (Charge Interface)充电接口:Micro (Low Voltage Alarm)低电压报警:3.4V (Battery Type)电池类型:Lithium Polyer Battery (Battery Capacity)电池容规格:2500mAh 3.
-EXPLORE Memo 备忘录 EN WWW.OMPHOBBY.
Zhuhai edge smart dirve technology Co., Ltd www.omphobby.