Datasheet

ManualsBrandsOmron Electronic Components ManualsMicroswitchesMicro Switch D2FS, 100mA, 1NO, 0.25N, Hinge Lever

D2FS

Ultra Subminiature Basic Switch

Simple construction and

high reliability for long time

• Developed for a few number of operations during a

long period of use such as door-detection to avoid

sabotage on meters.

• Simple construction with a single-leaf movable

spring realizes reasonable cost.

• Self-clinching, right-angled and left-angled

PCB terminals are also available.

RoHS Compliant

Model Number Legend

List of Models

Contact Form

● SPST-NO

Contact Specifications

Note: For more information on the minimum applicable load, refer to Using Micro Loads.

Actuator Terminals Model

Pin plunger PCB terminals (Straight) D2FS-F-N

PCB terminals (Self-clinching) D2FS-F-N-T

PCB terminals (Right-angled) D2FS-F-N-A

PCB terminals (Left-angled) D2FS-F-N-A1

Hinge lever PCB terminals (Straight) D2FS-FL-N

PCB terminals (Self-clinching) D2FS-FL-N-T

PCB terminals (Right-angled) D2FS-FL-N-A

PCB terminals (Left-angled) D2FS-FL-N-A1

Contact

Specification Crossbar

Material Silver

Gap (standard value) 0.4 mm

Minimum applicable load (see note) 1 mA at 5 VDC

D2FS - F

-N

1. Actuator

None : Pin plunger

L : Hinge lever

2. Terminals

None : PCB terminals (Straight)

-T : PCB terminals (Self-clinching)

-A : PCB terminals (Right-angled)

-A1 : PCB terminals (Left-angled)

COM NO

Summary of content (4 pages)

PAGE 1
D2FS Ultra Subminiature Basic Switch Simple construction and high reliability for long time • Developed for a few number of operations during a long period of use such as door-detection to avoid sabotage on meters. • Simple construction with a single-leaf movable spring realizes reasonable cost. • Self-clinching, right-angled and left-angled PCB terminals are also available. RoHS Compliant Model Number Legend D2FS - F @ - N @ 1 2 1. Actuator None : Pin plunger L : Hinge lever 2.
PAGE 2
D2FS Ultra Subminiature Basic Switch Ratings Rated voltage Resistive load 6 VDC 0.1 A Note: The rating values apply under the following test conditions. Ambient temperature: 20 ± 2°C Ambient humidity: 65 ± 5% Operating frequency: 20 operations/min Characteristics Pin plunger models: 1 mm to 500 mm/s Lever models: 5 mm to 500 mm/s Operating speed Operatiing frequency Mechanical Pin plunger models: 200 operations/min max. Lever models: 100 operations/min max. Electrical 30 operations/min max.
PAGE 3
D2FS Ultra Subminiature Basic Switch Terminals (Unit: mm) ● PCB Terminals (Straight) ● PCB terminals (Self-clinching) PCB Mounting Dimensions (Reference) Three, 1.2 dia. 5.08±0.1 5.08±0.1 1.6±0.15 3.5 3.15 3.5 COM NO terminal terminal 6.5±0.1 5.08±0.15 5.08±0.15 Dummy terminal 0.4 3.15 5.8±0.15 COM NO terminal terminal 6.5±0.1 5.08±0.15 5.08±0.15 12.8±0.15 1.5 Dummy terminal 0.9±0.1 0.4±0.15 1.25±0.15 5.8±0.15 12.8±0.15 ● PCB Terminals (Right-angled) ● PCB Terminals (Left-angled) 2.6±0.
PAGE 4
D2FS Ultra Subminiature Basic Switch Precautions Refer to General Information. Cautions Correct Use ● Soldering ● Handling • When using automatic soldering baths, we recommend soldering at 260°C within 5 seconds. Make sure that the liquid surface of the solder does not flow over the edge of the board. • When soldering terminals manually, perform soldering within 3 seconds at iron tip temperature not higher than 350°C. Do not apply any external force for at least 1 minute after soldering.