Datasheet
2
D2JW Sealed Subminiature Basic Switch
D
2
J
W
Contact Specifications
Ratings
Note. The above rating values apply under the following test conditions.
(1) Ambient temperature: 20±2°C
(2) Ambient humidity: 65±5%
(3) Operating frequency: 30 operations/min
Characteristics
Note. The data given above are initial values.
*1. The dielectric strength values shown apply for use with Separator (refer
to page 4).
*2. For the pin plunger models, the above values apply for use at the free
position and total travel position. For the lever models, they apply at the
total travel position. Close or open circuit of the contact is 1ms max.
*3. For testing conditions, consult your OMRON sales representative.
Mounting Holes (Unit: mm)
Dimensions (Unit: mm) /Operating Characteristics
Dimensions and operating characteristics of other actuator models for lead wire models are omitted in the illustration below, as the
dimensions other than the termial part and operatiing characteristics is common with Solder terminal models.
Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
Contact
Specification Crossbar
Material Gold alloy
Gap (standard
value)
0.5 mm
Inrush current
NC 0.1A max.
NO 0.1A max.
Minimum applicable load (see
note)
5 VDC 1 mA
Rated voltage Resistive load
30 VDC 0.1A
Permissible operating speed
1 mm to 250 mm/s
(for pin plunger models)
Permissible
operating
frequency
Mechanical 240 operations/min
Electrical 30 operations/min
Insulation resistance
100 M
Ω
min.
(at 500 VDC with insulation tester)
Contact
resistance
(initial value)
Solder terminal models 100 m
Ω
max.
Molded lead wire models 140 m
Ω
max.
Dielectric
strength * 1
Between terminals of the same
polarity
600 VAC 50/60 Hz 1min
Between current-carrying metal
parts and ground
1,000 VAC 50/60 Hz 1min
Between each terminal and
non-current-carrying metal parts
1,000 VAC 50/60 Hz 1min
Vibration
resistance * 2
Malfunction
10 to 55 Hz, 1.5 mm double
amplitude
Shock
resistance
Durability 1,000 m/s
2
{approx. 100G} max.
Malfunction * 2 200 m/s
2
{approx. 20G} max.
Durability * 3
Mechanical
1,000,000 operations min.
(60 operations/min)
Electrical
100,000 operations min.
(30 operations/min)
Degree of
protection
Solder terminal models
IEC IP67 (excluding the terminals
on terminal models)
Molded lead wire models IEC IP67
Ambient operating temperature
−
40°C to +85°C (at ambient
humidity of 60% max.)
(with no icing or condensation)
Ambient operating humidity 35% to 98% (for +5°C to +35°C)
Weight
Approx. 0.6g (for pin plunger
models with terminals)
M2.3 mounting screw hole
4.8
±0.1
0.40.5
5.3
±0.1
12.3
9.4
1.3
2.8
2.35
+0.05
dia.
−0.025
2.35
+0.05
−0.025
2.5
+0.05
dia.
−0.025
12.7
3.95
3.953.95
4.8
±0.05
1
2
1.6 dia.
A
Pretravel (PT)
Operating
Position (OP)
●Pin plunger models
D2JW-011
Operating characteristics
Operating Force OF Max.
Releasing Force RF Min.
2.45 N {250 gf}
0.98 N {100 gf}
Pretravel PT Max.
Overtravel OT Min.
Movement Differential MD Max.
0.6 mm
0.3 mm
0.1 mm
Operating Position OP
8.1±0.3 mm
12.3
9.4
1.3
2.8
2.35
+0.05
dia.
−0.025
2.35
+0.05
−0.025
2.5
+0.05
dia.
−0.025
7.95
1.8
Pretravel (PT)
Operating
Position
(OP)
6.15
R11.5
12.7
3.95
3.953.95
4.8
±0.05
1
2
t0.3 Stainless-steel
lever
A
5.3
±0.1
3
0.40.5
●Short hinge lever models
D2JW-01K1A1
Operating Force OF Max.
Releasing Force RF Min.
1.15 N {117 gf}
0.23 N {23 gf}
Pretravel PT Max.
Overtravel OT Min.
Movement Differential MD Max.
5.4 mm
0.7 mm
0.5 mm
Operating Position OP
8.4±0.8 mm