Datasheet

ManualsBrandsOmron Electronic Components ManualsMicroswitchesMicro Switch D2SW, 3A, 1CO, 1.77N, Pin Plunger

671

Text

670

Text Subminiature Basic Switch (Sealed) – D2SW

Sealed Microswitches

Note: The ratings values apply under the following test

conditions:

Ambient temperature: 20±2˚C

Ambient humidity:65±5%

Operating frequency: 30 operations/min

Item Resistive Load

Type Rated Load

D2SW-3 250VAC 3A

125VAC 2A

30VDC 3A

D2SW-01 125VAC 0.1A

30VDC 0.1A

Subminiature Basic Switch (Sealed) – D2SW

High-quality Sealed Sub Miniature

Basic Switch Conforming to IP67 (Lead

wire type only)

■

ROHS Compliant.

■

Monoblock construction assures high sealing

capability and is ideal for dusty places or where

water is sprayed.

■

A wide operating temperature range of -40°C to

85°C is ideal for any operating environment.

■

Ideal for the automobile, agricultural machinery,

automatic vending machine, refrigerator,

ice-manufacturing, bath equipment, hot-water

supply, air conditioner, and factory machine

industries, which require highly environment-

resistive capabilities.

Switching Capacity per Load (Reference Values)

Note: 1. The standard lengths of the lead wires (AV0.5f) of models incorporating them are 30cm.

2. Consult your Omron sales representative for details on SPST-NO and SPST-NC models.

3. Add "HS", "TS", or "MS" to the end of the model number for the UL/CSA-approved version. (e.g. D2SW-3H D2SW-

3HS). Consult your Omron sales representative for details.



Omron 08 Cat 565-773 5/10/07 15:58 Page 670

Summary of content (6 pages)

PAGE 1
Omron 08 Cat 565-773 5/10/07 15:58 Page 670 Subminiature Basic Switch (Sealed) – D2SW Text Text Subminiature Basic Switch (Sealed) – D2SW High-quality Sealed Sub Miniature Basic Switch Conforming to IP67 (Lead wire type only) Item Resistive Load ■ ROHS Compliant. Type Rated Load ■ Monoblock construction assures high sealing D2SW-3 250VAC 125VAC 3A 2A 30VDC 3A capability and is ideal for dusty places or where water is sprayed.
PAGE 2
Omron 08 Cat 565-773 5/10/07 15:58 Page 670 Subminiature Basic Switch (Sealed) – D2SW Text Text Subminiature Basic Switch (Sealed) – D2SW High-quality Sealed Sub Miniature Basic Switch Conforming to IP67 (Lead wire type only) Item Resistive Load ■ ROHS Compliant. Type Rated Load ■ Monoblock construction assures high sealing D2SW-3 250VAC 125VAC 3A 2A 30VDC 3A capability and is ideal for dusty places or where water is sprayed.
PAGE 3
Omron 08 Cat 565-773 5/10/07 15:58 Page 672 Subminiature Basic Switch (Sealed) – D2SW Text Text Subminiature Basic Switch (Sealed) – D2SW Contact Form SPDT SPST-NC (Molded lead wire models only) SPST-NO (Molded lead wire models only) Sealed Microswitches Note: For more information on the minimum applicable load, refer to Using Micro Loads. Note: AV 0.5f wires are used for standard lead wire model. UL1015 AWG22 wires are used for UL/CSA approved models.
PAGE 4
Omron 08 Cat 565-773 5/10/07 15:58 Page 672 Subminiature Basic Switch (Sealed) – D2SW Text Text Subminiature Basic Switch (Sealed) – D2SW Contact Form SPDT SPST-NC (Molded lead wire models only) SPST-NO (Molded lead wire models only) Sealed Microswitches Note: For more information on the minimum applicable load, refer to Using Micro Loads. Note: AV 0.5f wires are used for standard lead wire model. UL1015 AWG22 wires are used for UL/CSA approved models.
PAGE 5
Omron 08 Cat 565-773 5/10/07 15:58 Page 674 Subminiature Basic Switch (Sealed) – D2SW Text Text Subminiature Basic Switch (Sealed) – D2SW Sealed Microswitches Note: AV 0.5f wires are used for standard lead wire model. UL1015 AWG22 wires are used for UL/CSA approved models Using Micro Loads Using a model for ordinary loads to open or close the contact of a miroload circuit may result in faulty contact. Use models that operate in the following range.
PAGE 6
Omron 08 Cat 565-773 5/10/07 15:58 Page 674 Subminiature Basic Switch (Sealed) – D2SW Text Text Subminiature Basic Switch (Sealed) – D2SW Sealed Microswitches Note: AV 0.5f wires are used for standard lead wire model. UL1015 AWG22 wires are used for UL/CSA approved models Using Micro Loads Using a model for ordinary loads to open or close the contact of a miroload circuit may result in faulty contact. Use models that operate in the following range.