Datasheet

ManualsBrandsOmron Electronic Components ManualsMicroswitchesMicro Switch SSG, 100mA, 1CO, 1.5N, Hinge Lever

SSG

Subminiature Basic Switch

Global Subminiature Basic

Switch Conforming to

EN61058-1 (IEC601058-1),

UL1054, and CSA C22.2 No.54

• A wide operating temperature range of –25°C to 125°C

is available for at high-temperature use.

• PCB terminal models are resistant to flux.

• Even-pitched PCB terminals.

• Mounting hole size of M2.2.

RoHS Compliant

ERC

Model Number Legend

SSG-

@@@@@

1. Ratings

5 : 5 A at 125 VAC

01 : 0.1 A at 125 VAC

2. Actuator

None : Pin plunger

L1 : Hinge lever

L2 : Hinge roller lever

L3 : Simulated roller lever

12345

3. Contact Form

None : SPDT

-2 : SPST-NC

-3 : SPST-NO

4. Terminals

H : Solder terminals

T : Quick-connect terminals (#110)

P : PCB terminals (SPDT only)

5. Maximum Operating Force

None : 1.5 N {153 gf}

-5 : 0.5 N {51 gf}

Note. These values are for the pin plunger models.

Separator (Sold Separately), Terminal Connector (Sold Separately) Refer to "Basic Switch Common Accessories"

Summary of content (8 pages)

PAGE 1
SSG Subminiature Basic Switch Global Subminiature Basic Switch Conforming to EN61058-1 (IEC601058-1), UL1054, and CSA C22.2 No.54 • A wide operating temperature range of –25°C to 125°C is available for at high-temperature use. • PCB terminal models are resistant to flux. • Even-pitched PCB terminals. • Mounting hole size of M2.2. ERC RoHS Compliant Model Number Legend 1 SSG-@ 1. Ratings 5 : 5 A at 125 VAC 01 : 0.1 A at 125 VAC 2.
PAGE 2
SSG Subminiature Basic Switch List of Models Ratings Actuator Terminals Solder terminals Pin plunger Quick-connect terminals (#110) SSG-01H SSG-01T SSG-5P SSG-01P SSG-5H-5 SSG-01H-5 SSG-5T-5 SSG-01T-5 0.50 N {51 gf} PCB terminals SSG-5P-5 SSG-01P-5 Solder terminals SSG-5L1H SSG-01L1H Quick-connect terminals (#110) SSG-5L1T SSG-01L1T PCB terminals SSG-5L1P SSG-01L1P Solder terminals SSG-5L1H-5 SSG-01L1H-5 0.
PAGE 3
SSG Subminiature Basic Switch Ratings Models Characteristics Item Rated voltage Resistive load 125 VAC 5A 250 VAC 3A SSG-5 SSG-01 125 VAC 0.1 A 30 VDC 0.1 A Note: 1. The above current ratings are the values of the steady-state current. 2. If the Switch is used in a DC circuit and is subjected to a surge current, connect a surge suppressor across the switch. 3.
PAGE 4
SSG Subminiature Basic Switch Dimensions (Unit: mm) and Operating Characteristics The illustrations and drawings are for solder terminals models and PCB terminals models. Refer to "Terminals/Appearances" of the previous page for details on models with quick connect terminals (#110). The @ is replaced with the code for the terminal that you need. See the "List of Models" for available combinations of models.
PAGE 5
SSG Subminiature Basic Switch ● Simulated Roller Lever SSG-5L3@ SSG-5L3@-5 SSG-01L3@ SSG-01L3@-5 Model OF max. RF min. A 1.3R SSG-5L3@-5 SSG-01L3@-5 0.60 N {61 gf} 0.06 N {6 gf} 0.20 N {20 gf} 0.02 N {2 gf} OT min. MD max. 6.3±0.4 3.6 t0.3 Stainless-steel lever FP max. OP FP 2.2 +0.1 0 SSG-5L3@ SSG-01L3@ 1.0 mm 0.8 mm 15.5 mm +1.0 10.7 − 0.6 mm OP 6.9 7.7 2.2 C NO NC 6.1 2.2+0.1 0 dia. hole 2.5 dia. 5.1 9.5±0.1 7.2 8.9 1.6 3.2 6.4±0.2 Three, 1.6-dia. holes 0.5 19.
PAGE 6
SSG Subminiature Basic Switch ● Hinge Roller Lever SSG-5L2P SSG-5L2P-5 SSG-01L2P SSG-01L2P-5 Model OF max. RF min. A 4.8 dia. × 3.2 Acetal resin roller 5±0.4 t0.3 Stainless-steel lever SSG-5L2P SSG-01L2P SSG-5L2P-5 SSG-01L2P-5 0.60 N {61 gf} 0.06 N {6 gf} 0.20 N {20 gf} 0.02 N {2 gf} OT min. MD max. 1.0 mm 0.8 mm FP max. OP 22.4 mm +1.1 17.9 − 0.7 mm 2.87±0.1 OP 2.2+0.1 0 3.4±0.1 6.9 7.7 C NO 2.5 dia. 5.15 7.62±0.2 FP NC 2.2+0.1 0 dia. hole Three, 1.2±0.1 1.3±0.3 0.5±0.05 Three, 0.8 6.
PAGE 7
SSG Subminiature Basic Switch Precautions Refer to General Information. Cautions Correct Use ● Terminal Connection ● Mounting When soldering the lead wire to the terminal, first insert the lead wire conductor through the terminal hole and then take the following steps promptly. • Make sure that the capacity of the soldering iron is 60 W (temperature of soldering iron : 350 to 400°C) maximum. Do not take more than 3 s to solder the switch terminal.
PAGE 8
SSG Subminiature Basic Switch • Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.