Datasheet

A22NE-PD
19
A22NE-PD A22NE-P A22E Common Note
Common Accessories and Tools
Checking Connections
• After the insertion, pull gently on the wire to make sure that it will
not come off and it is securely fastened to the terminal block.
• If you use a ferrule with a conductor length of 10 mm, part of the
conductor may be visible after the ferrule is inserted into the
terminal block, but the product insulation distance will still be
satisfied.
2. Removing Wires from the Push-In Plus Terminal Block
Use the following procedure to remove wires from the terminal block.
The same method is used to remove stranded wires, solid wires, and ferrules.
1. Hold a flat-blade screwdriver at an angle and insert it into the
release hole. The angle should be appropriately 10 to 15°.
2. With the flat-blade screwdriver still inserted into the release hole,
remove the wire from the terminal insertion hole.
3. Remove the flat-blade screwdriver from the release hole.
3. Recommended Ferrules and Crimp Tools
Coating peeling amount
Recommended ferrules
Note: 1. Make sure that the outer diameter of the wire coating is
smaller than the inner diameter of the insulation sleeve of
the recommended ferrule.
2. Make sure that the ferrule processing dimensions conform
to the following figures.
Recommended Flat-Blade Screwdrivers
Use a flat-blade screwdriver to connect and remove wires.
Use one of the following flat-blade screwdrivers.
The following table shows manufacturers and models as of 2015/Dec.
* The SZF 0-0,4 × 2,5 (manufactured by Phoenix Contact) can be
procured through an OMRON exclusive purchase form (XW4Z-00B).
• After wiring the Switch/Indicator, provide a sufficient insulation
distance.
(2)
(1)
(3)
Flat-head screwdriver
Approx.
10 to 15°
Recommend Wire Type
Stripping length
(Ferrules not used)
0.25 to 1.5 mm
2
/AWG 24 to AWG 16 8 mm
Applicable
wire
Ferrule
conductor
length
(mm)
Stripping
length (mm)
(Ferrules not
used)
Recommended ferrules
(mm
2
) (AWG)
Phoenix
Contact
product
Weidmuller
product
Wago
product
0.25 24
8 10 AI 0, 25-8 H0.25/12 216-301
10 12 AI 0, 25-10 --- ---
0.34 22
8 10 AI 0, 34-8 H0.34/12 216-302
10 12 AI 0, 34-10 --- ---
0.5 20
8 10 AI 0, 5-8 H0.5/14 216-201
10 12 AI 0, 5-10 H0.5/16 216-241
0.75 18
8 10 AI 0, 75-8 H0.75/14 216-202
10 12 AI 0, 75-10 H0.75/16 216-242
1/1.25 18/17
8 10 AI 1-8 H1.0/14 216-203
10 12 AI 1-10 H1.0/16 216-243
1.25/1.5 17/16
8 10 AI 1, 5-8 H1.5/14 216-204
10 12 AI 1, 5-10 H1.5/16 216-244
Recommended Crimp Tools
CRIMPFOX6
CRIMPFOX6T-F
CRIMPFOX10S
PZ6 roto
Variocri
mp4
Model Manufacture
ESD 0,40 × 2,5 Wera
SZS 0,4 × 2,5
SZF 0-0,4 × 2,5 *
Phoenix Contact
0.4 × 2.5 × 75 302 Wiha
AEF.2,5 × 75 Facom
210-719 Wago
SDI 0,4 × 2,5 × 75 Weidmuller
8 to 10 mm
Max. 1.9 mm
Max. 2.6 mm
Side view
0.4 mm
2.5 mm dia.
2.5 mm
Front view