Datasheet

G2RV-SR/G3RV-SR
23
G2RV-SR G3RV-SR
Common AccessoriesCommon Precautions
3. Recommended ferrules and Crimp Tools
Recommended ferrules
Note: 1. Make sure that the outer diameter of the wire is smaller than
the inner diameter of the insulating sleeve of the
recommended ferrule.
2. Make sure that the ferrule processing dimensions conform
to the following figure.
3. If you use AWG24 to AWG22 (0.25 to 0.34 mm
2
) wires, UL
certification will not apply.
Recommended Flat-blade Screwdriver
Use a flat-blade screwdriver to connect and remove wires.
Use the following flat-blade screwdriver.
The following table shows manufacturers and models as of 2015/Dec.
* OMRON's exclusive purchase model XW4Z-00B is available to
order as SZF 0-0
,4×2,5 (manufactured by Phoenix Contact).
Screw Terminal
• Screw terminal
• Tightening Torque
0.4 N • m
• Electric wiring
Use the electric wire of specified size as shown above. The length
of the that is not covered is 8 mm.
<G2RV>
Operating latching lever (test switch)
When operating the latching lever for G2RV-SR701/501
series, use a 2.5 mm width flat-blade screwdriver.
• Applicable flat-blade screwdriver
Flat-blade screwdriver with parallel cutting edge: shaft diameter
2.5 mm (3.0 mm max.)
• Always turn OFF the power supply before operating latching lever.
• Return to its original state after using the latching lever.
• Do not use the latching lever as a switch.
• Operation durability of the latching lever is 100 times or more.
• Do not keep the latching lever ON for a long period of time (24
hours or more) in order to maintain the operation check function.
Applicable
wire
Ferrules
Conduct
length
(mm)
Stripping
length
(mm)
(Ferrules
used)
Recommended ferrules
(mm
2
) (AWG)
Phoenix Contact
product
Weidmuller
product
Wago
product
0.25 24
8 10 AI 0,25-8 H0.25/12 216-301
10 12 AI 0,25-10 --- ---
0.34 22
8 10 AI 0,34-8 H0.34/12 216-302
10 12 AI 0,34-10 --- ---
0.5 20
8 10 AI 0,5-8 H0.5/14 216-201
10 12 AI 0,5-10 H0.5/16 216-241
0.75 18
8 10 AI 0,75-8 H0.75/14 216-202
10 12 AI 0,75-10 H0.75/16 216-242
1/1.25 18/17
8 10 AI 1-8 H1.0/14 216-203
10 12 AI 1-10 H1.0/16 216-243
1.25/1.5 17/16
8 10 AI 1,5-8 H1.5/14 216-204
10 12 AI 1,5-10 H1.5/16 216-244
Recommended crimp tool
CRIMPFOX6
CRIMPFOX6T-F
CRIMPFOX10S
PZ6 roto Variocrimp4
Model Manufacturer
ESD 0,40×2,5 Wera
SZS 0,4×2,5
SZF 0-0,4×2,5 *
Phoenix Contact
0.4×2.5×75 302 Wiha
AEF.2,5×75 Facom
210-719 Wago
SDI 0.4×2.5×75 Weidmuller
8 to 10 mm
1.9 mm max.
2.6 mm max.
Side
0.4 mm
2.5 mm dia.
2.5 mm
Front
Wired type
Applicable wire
size
Stripping
length
Stranded wires, without
ferrule
0.5 to 1.5 mm
2
8 mm
Stranded wires, with ferrule
and plastic collar
0.5 to 1.5 mm
2
8 mm
Stranded wires with ferrule,
without plastic collar
0.5 to 1.5 mm
2
8 mm
Single wire 0.5 to 1.5 mm
2
8 mm
Stripping length
8 mm
Screw terminal
Shaft diameter 2.5 mm (3.0 mm max.)
Driver with a thick shaft cannot be used.
Wide flat-blade screwdriver
Parallel cutting edge flat-blade screwdriver