Datasheet

10 Multifunction Counter H7BX
When using the H7BX as a Total and Preset Counter, Batch Counter, or Dual Counter, switch the configuration using the procedure on page 23.
■ Setting Advanced Functions
Settings that cannot be performed with the DIP switch are performed with the operation keys.
See note 2.
See note 3.
See note 7.
Note 3: When using as a dual counter
Note 6: For models with a 2-stage setting, the input mode is
displayed only when an Up/Down Mode is selected.
Note: Displayed only when the output mode is C, R, K-1, P,
Q, A, or K-2.
Note 5: Displayed for output modes other than K-2, D, L, and H only.
See note 1.
Note 7: Set the number for each digit with the Keys.
See note 5.
See note 5.
Input mode
Output time
Output 2
time
(OTM2)
Output 1
time
(OTM1)
Dual count
calculating mode
(ADD)
Output mode
(CNTM)
(OUTM)
(OTIM)
(CNTS)
(IFLT)
(DP)
(PSCL)
(KYPT)
Min. reset
period
Key
Protection
Level
(1 ms)(20 ms)
No decimal
point
One digit after
decimal point
Two digits after
decimal point
Three digits after
decimal point
Decimal point
position
Prescale
value
Counting
speed
(30 Hz) (5 kHz)
(PNP
input)
(NPN
input)
(Red) (Green) (Red-
green)
(Green-
red)
The characters displayed in reverse video are the default settings.
When performing settings with operation keys only, turn OFF pin 1 of the DIP switch (factory setting).
If pin 1 of the DIP switch is ON, the setting items indicated by will not be displayed.
3 s min.3 s min.
(N)
(0.50 s) (99.99 s)(0.01 s)
(0.50 s)(99.99 s)(0.01 s)
Output 2
time
(OTM2)
(0.01 s) (99.99 s) (Outputs held)
(F) (C) (R) (K-1) (P) (Q) (A) (K-2) (D) (L) (H)
See note 6. See note 6. See note 6. See note 6.
(Addition)(Subtraction)
(DOWN) (UP/DOWN A) (UP/DOWN B) (UP/DOWN C) (UP)
(KP-1) (KP-2) (KP-3) (KP-4) (KP-5)
(99.999) (1.000)(0.001)
(0.50 s) (99.99 s)(0.01 s)
See note 4.
Up
Up
Up
Up
Up
Up
Up
Up
Up
Up
Up
Up
Note: Displayed only when the
output mode is C, R,
K-1, P, Q, A, or K-2.
Note 1: Displayed for output
modes other than D, L,
and H.
Note 2: HOLD cannot be set
when the output mode
is K-2.
Note: Displayed only when the
output mode is C, R, K-1,
P, Q, A, or K-2.
Note 4: Displayed only when
the output mode is
K-2, D, L, or H.
NPN/PNP
input mode
(IMOD)
Display
color
(COLR)
Power ON
Run mode
Function setting mode
• Set the input mode with any of the Keys.
• Set the output mode with any of the Keys.
• Set the number for each digit with the Keys.
• Set the dual count calculating mode
the Key.
• Set the NPN/PNP input mode with any of the Keys.
• Set the display color with any of the Keys.
• Set the key protect level with any of the Keys.
• Set the counting speed with any of the Keys.
• Set the min. reset input signal width with any of the Keys.
• Set the decimal point position with any of the Keys.
• Set the number for each digit with the Keys.
● 2-stage Preset Counter
● Batch Counter
If the output time is 0.00,
hold is displayed.
Note: 1. If the mode is switched to the function setting mode during operation, operation will continue.
2. Changes made to settings in function setting mode are enabled for the first time when the
mode is changed to run mode. Also, when settings are changed, the counter is reset (present
value initialized and output turned OFF) on returning to run mode.
For details on operations and display in run mode, refer to page 12. The display depends on the configuration used.