Datasheet

ManualsBrandsOmron Industrial Automation ManualsAutomationLimit Switch, Adjustable Rod Lever, 1NC + 1NO,

CSM_HL-5000_DS_E_3_2

General-purpose Limit Switch

HL-5000

Economical, Miniature Limit Switch

Boasting Rigid Construction

• The Head, Box, and Cover mate with ridged surfaces to

maintain strength.

•

A unique Head structure provides a large OT for smooth operation.

• Easy-to-wire conduit opening design.

• Ideal for application in printing machines, forming machines,

and light machines.

(High Switches with high sealing characteristics, such as WL or

D4C Switches, in locations subject to oil, water, or precipitation.)

• Models with grounding terminals conform to the CE marking.

• Approved by CCC (Chinese standard).

(Ask your OMRON representative for information on approved models.)

Be sure to read Safety Precautions on page 4 to 5 and

Safety Precautions for All Limit Switches.

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Model Number Structure

Model Number Legend

å`HL-5Å†Å†

(1)(2)

(1) Actuators

000: Roller lever

030: Adjustable roller lever

050: Adjustable rod lever

100: Sealed plunger

200: Sealed roller plunger

300: Coil spring

(2) Ground Terminal Specifications

Blank : Without ground terminal

G : With ground terminal/M5 tapping on the rear side

Ordering Information

* HL-5000 Limit Switches are offered with a choice of ground terminal/M5

tapping on the rear side conforming to various standards. When placing an

order, add the code to the model number to indicate if ground terminal/M5

tapping on the rear side is required.

-G: with ground terminal/M5 tapping on the rear side.

Specifications

Approved Standards

Note: Ask your OMRON representative for information on approved models.

Ratings

Note: 1. The above figures are for steady-state currents.

2. Inductive loads have a power factor of 0.4 min. (AC) and a time

constant of 7 ms max. (DC).

3. Lamp load has an inrush current of 10 times the steady-state current.

4. Motor load has an inrush current of 6 times the steady-state current.

Approved Standard Ratings

CCC (GB14048.5)

Actuator Model

Roller lever

HL-5000 *

Adjustable

roller lever

HL-5030 *

Adjustable

rod lever

HL-5050 *

Sealed

plunger

HL-5100 *

Sealed roller

plunger

HL-5200

Coil spring

HL-5300

(Not all combinations are possible. Ask

your OMRON representative for details.)

HL-5@@

Agency Standard File No.

CCC (CQC) GB14048.5 2003010303077624

Rated

voltage

Non-inductive load (A) Inductive load (A)

Resistive

load

Lamp load

Inductive

load

Motor load

NC NO NC NO NC NO NC NO

125 VAC 51.50.7 321

250 VAC 5 1 0.5 3 1.5 0.8

12 VDC 5343

24 VDC 5343

125 VDC 0.4 0.2 −−−

250 VDC 0.4 0.2 −−−

Inrush

current

NC 24 A max.

NO 12 A max.

Applicable category and ratings

AC-15 3 A/250 VAC

Summary of content (6 pages)

PAGE 1
General-purpose Limit Switch HL-5000 CSM_HL-5000_DS_E_3_2 Economical, Miniature Limit Switch Boasting Rigid Construction • The Head, Box, and Cover mate with ridged surfaces to maintain strength. • A unique Head structure provides a large OT for smooth operation. • Easy-to-wire conduit opening design. • Ideal for application in printing machines, forming machines, and light machines.
PAGE 2
HL-5000 Degree of protection Mechanical Durability * Electrical Operating speed Operating Mechanical frequency Electrical Insulation resistance Contact resistance Dielectric strength Rated frequency Vibration Malfunction resistance Destruction Shock resistance Malfunction Ambient operating temperature Ambient operating humidity Weight Engineering Data IP65 10,000,000 operations min. (under rated conditions) See the following Electrical Durability. 5 mm/s to 0.
PAGE 3
HL-5000 Dimensions and Operating Characteristics (Unit: mm) Switches (Dimensions not shown are the same as roller lever models.) Roller Lever HL-5000 Adjustable Roller Lever HL-5030 58 ±0.8 53 ±0.8 39.5 ±0.8 40.3 ±0.8 17.5 dia. × 6.6 resin roller *1 31.5R 39.5 ±0.8 32 16.5 Adjustable up to 30R to 75R 16.5 *2 *2 21.4 15.5 (110) M5 × 12 Allen-head bolt 50 ±0.2 60.6 Three, M3 21.4 M5 × 16 Allen-head bolt 15.5 M5 × 12 Allen-head bolt 50 ±0.2 65.7 ±0.8 60.3 ±0.8 51.3 ±0.8 17.5 dia. × 6.
PAGE 4
HL-5000 Safety Precautions Refer to Safety Precautions for All Limit Switches. Precautions for Correct Use Operating Environment Applicable Lead Wires • Seal material may deteriorate if a Switch is used outdoor or where subject to special cutting oils, solvents, or chemicals. Always appraise performance under actual application conditions and set suitable maintenance and replacement periods. • Install Switches where they will not be directly subject to cutting chips, dust, or dirt.
PAGE 5
HL-5000 Mounting Others To mount the Limit Switch securely, be sure to use two M5 Allenhead bolts and washers. The tightening torque applied to each bolt is 4.90 to 5.88 N·m. To mount the Limit Switch more securely, use two M5 screw holes on the rear panel and rear holes for positioning if the model is the HL5@@@G-Series Limit Switches. Mounting holes Two, 5.2-dia.
PAGE 6
Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON.