User's Manual

25
RFID System
User's Manual
Section 2 㪥㪫㪣㪧㩷㪠㪛䉶 䊮䉰
Section 2
㪥㪸㫄㪼㫊㩷㪸㫅㪻㩷㪝㫌㫅㪺㫋㫀㫆㫅㫊㩷㫆㪽㩷㪚㫆㫄㫇㫆㫅㪼㫅㫋㫊
Access Address Setting Switch
Set the operation mode for reading data.
㪫㪿㪼㩷㪸㪺㪺㪼㫊㫊㩷㪸㪻㪻㫉㪼㫊㫊㩷㫊㪼㫋㫋㫀㫅㪾㩷㫊㫎㫀㫋㪺㪿㪼㫊㩷㪸㫉㪼㩷㫉㪼㪸㪻㩷㫆㫅㫃㫐㩷㫎㪿㪼㫅㩷㫋㪿㪼㩷㫇㫆㫎㪼㫉㩷㫊㫌㫇㫇㫃㫐㩷㫀㫊㩷㫋㫌㫉㫅㪼㪻㩷㪦㪥㪅㩷
㪫㪿㪼㫉㪼㪽㫆㫉㪼㪃㩷㫊㪼㫋㫋㫀㫅㪾㫊㩷㪺㪸㫅㫅㫆㫋㩷㪹㪼㩷㪺㪿㪸㫅㪾㪼㪻㩷 㫎㪿㫀㫃㪼㩷 㫋㪿㪼㩷 㫇㫆㫎㪼㫉㩷㫀㫊㩷㪹㪼㫀㫅㪾㩷㫊㫌㫇㫇㫃㫀㪼㪻㪅㩷 㪫㫌㫉㫅㩷㫋㪿㪼㩷㫇㫆㫎㪼㫉㩷 㫊㫌㫇㫇㫃㫐㩷㪦㪝㪝㩷㪹㪼㪽㫆㫉㪼㩷 㪺㪿㪸㫅㪾㫀㫅㪾㩷 㫋㪿㪼
㫊㪼㫋㫋㫀㫅㪾㫊㪅
 Antenna Connector
Connect this connector to the V680-series Antenna.
The position of the arrow in the figure is
the direction in which the setting is made.
Item Description
Setting
method
Specify the memory address of the ID Tag in 4-digit hexadecimal.
To specify an ID Tag memory address of 01A3 hex:
Setting
range
0000 hex to FFFF hex (See note.)
Default setting: 0000 hex
Note: Note: The upper 8 bits are not read when FFFF hex is specified using 16-bit
read/write. Output for all will be OFF. .
0
1
A
3
2
1
Pin No. Name Signal type I/O
1 S Signal line ---
2 GND Analog ground ---