INSTRUCTION MANUAL 7 series Automatic Wrist Blood Pressure Monitor ENGLISH ESPAÑOL Model BP652
TABLE of OF contents CONTENTS table Before using the Monitor Introduction .......................................................................................................... 3 Safety Information . ............................................................................................... 4 Operating the Device ........................................................................... 4 Care and Maintenance .........................................................................
Introduction Thank you for purchasing the OMRON® BP652 IntelliSense® Automatic Wrist Blood Pressure Monitor. Fill in for future reference. DATE PURCHASED:__________________ SERIAL NUMBER:____________________ • Staple your purchase receipt here • Register your product on-line at www.register-omron.com The monitor is compact and easy-to-use at home, at work, and during travel. Perfect for people who frequently monitor their own blood pressure.
SAFETY INFORMATION To assure the correct use of the product, basic safety measures should always be followed including the warnings and cautions listed in this instruction manual. SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
SAFETY INFORMATION Do not use a cellular phone near the device. It may result in an operational failure. Use only Omron authorized parts and accessories. Parts and accessories not approved for use with the device may damage the unit. Use only 1.5 V “AAA” alkaline batteries with this device. Do not use other types of batteries. This may damage the unit. CARE AND MAINTENANCE Do not subject the monitor to strong shocks, such as dropping the unit on the floor.
BEFORE TAKING A MEASUREMENT To ensure a reliable reading follow these recommendations: 1. Avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes before taking a measurement. Rest for at least 15 minutes before taking the measurement. 2. Stress raises blood pressure. Avoid taking measurements during stressful times. 3. The cuff can be applied to your left or right wrist. 4. Measurements should be taken in a quiet place. 5.
KNOW YOUR UNIT Main Unit: Display Wrist cuff Memory (MEM) button START/STOP button Date/Time Setting ( ) button User ID selection switch Date/Time Setting ( ) button SET button Battery compartment Components: INSTRUCTION MANUAL 7 series Automatic Wrist Blood Pressure Monitor Model BP652 5329415-9A INTRODUCTION Thank you for purchasing the OMRON® BP652 IntelliSense® Automatic Wrist Blood Pressure Monitor . Fill in for future reference.
UNIT DISPLAY Heart guide indicator Diastolic blood pressure Memory symbol (Displayed when viewing values stored in memory) Average value symbol (Refer to “Using the Memory Function” .) Systolic blood pressure Deflation symbol Irregular heartbeat symbol Movement error symbol (Displayed if you move your body during the measurement) Blood pressure level indicator Buzzer symbol User ID symbol (A or B) (If “GUEST” is selected, A or B will not be displayed.
DISPLAY SYMBOLS IRREGULAR HEARTBEAT SYMBOL ( ) When the monitor detects an irregular rhythm two or more times during the measurement, the Irregular Heartbeat Symbol ( ) will appear on the display with the measurement values. An irregular heartbeat rhythm is defined as a Normal Heartbeat rhythm that varies by less than 25% from the Pulse average rhythm or 25% more than the average Blood rhythm detected while the monitor is measuring pressure the systolic and diastolic blood pressure.
DISPLAY SYMBOLS This is a general guideline because blood pressure depends on age and morbidity. A lower home blood pressure goal may be recommended for certain patients, including diabetic patients, pregnant women, and patients with renal failure. WARNING Contact your physician for specific information about your blood pressure. Self-diagnosis and treatment using measured results may be dangerous. Follow the instructions of your physician or licensed healthcare provider.
BATTERY INSTALLATION CAUTION Use only 1.5V “AAA” alkaline batteries with this device. 1. Press the hook on the bottom of the battery cover and lift the cover off in the direction of the arrow. 2. Install 2 “AAA” size batteries so the + (positive) and (negative) polarities match the polarities of the battery compartment as indicated. 3. Set the date and time. Refer to “Setting the Date and Time”. 4. Replace the battery cover. NOTE: Make sure that the battery cover is securely in position.
BATTERY INSTALLATION BATTERY REPLACEMENT Low Battery Indicator When the Low Battery Indicator appears on the display, turn the monitor off and remove all the batteries. Replace with 2 new batteries at the same time. Long-life alkaline batteries are recommended. WARNING If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Contact a physician immediately. NOTES: • Turn the unit off before replacing the batteries.
SETTING THE DATE AND TIME Set the monitor to the current date and time before taking a measurement for the first time. 1. TO START THE SETTING Press the Date/Time Setting button ( ) to adjust the date and time. The year flashes on the display. 2. SETTING THE YEAR Press the Date/Time Setting button ( ) to advance by increments of one year. Press the Date/Time Setting button ( ) to set the current year. The month flashes on the display. NOTES: • The year can be set between 2009 and 2030.
SETTING THE DATE AND TIME 4. SETTING THE DAY Press the Date/Time Setting button ( ) to advance by increments of one day. Press the Date/Time Setting button ( ) to set the current day. The hour flashes on the display. 5. SETTING THE HOUR The time is set using AM or PM. Press the Date/Time Setting button ( ) to advance by increments of one hour. Press the Date/Time Setting button ( ) to set the current hour. The minute flashes on the display. 6.
SETTING THE HEART GUIDE INDICATOR You can change the options for various settings on your monitor. Pressing the SET button to change a setting. Press the MEM button to select the options for that setting. After selecting a setting, press the START/STOP button to confirm the setting and turn the power off. SETTING THE HEART GUIDE INDICATOR 1. Select your User ID. 2. Press the SET button. NOTE: The default setting is “on1”. User A User B 3.
SETTING THE HEART GUIDE INDICATOR SETTING FOR RIGHT OR LEFT WRIST MEASUREMENT 1. While in the setting mode, press the SET button until the wrist symbol ( or ) appears on the display. NOTES: • The default setting is “ ”. • After you choose “oFF” for the Heart guide indicator, the monitor skips this process. 2. Press the MEM button to select the left wrist ( ) or the right wrist ( ). SETTING THE BUZZER 1.
SETTING THE HEART GUIDE INDICATOR 2. Press the MEM button to select the buzzer setting. If the Heart guide indicator is “on1” or “on2”: on1: The buzzer sounds only when the monitor is in proper position. on2: The buzzer sounds a series of two short blips if your wrist is too far away from the measuring position, and beeps when your wrist is in the proper position. oFF: The buzzer will not sound. If the Heart guide indicator is “oFF”: on: The buzzer sounds when pressing any buttons.
APPLYING THE WRIST CUFF CAUTION Read all of the information in the instruction manual and any other literature in the box before operating the unit. CAUTION This device is intended for use in measuring blood pressure and pulse rate in the adult population. Do not use this device on infants or persons who cannot express their intentions. APPLYING THE CUFF ON THE LEFT WRIST 1. Roll up sleeve. Make sure your sleeve is not rolled up too tightly on your arm. This may constrict the flow of blood in your arm.
APPLYING THE WRIST CUFF 5. Fold the remaining part of the wrist cuff back out of the way. APPLYING THE CUFF ON THE RIGHT WRIST When taking a measurement using the right wrist position the cuff as shown in the illustration. Refer to “Setting for Right or Left Wrist for Measurement”.
TAKING A MEASUREMENT The monitor is designed to take measurements and store the measurement values in memory for two people using USER ID A and USER ID B. The monitor can be used to take a single measurement using the GUEST mode are not stored in the memory. 1. Sit comfortably in a chair with your feet flat on the floor. 2. Select your User ID (A or B). User A 3. Press the START/STOP button. All symbols appear on the display.
TAKING A MEASUREMENT 4. Hold your arm across your chest at heart level. Hold your elbow firmly to avoid body movement. Sit still and do not talk or move during the measurement. If the Heart Guide Indicator is set to “on2”, the orange light will turn to blue when your arm is in the correct position. (If set to either “on1” or “oFF”, the cuff will inflate automatically.) The cuff starts to inflate automatically. As the cuff inflates, the monitor automatically determines your ideal inflation level.
TAKING A MEASUREMENT 6. Press the START/STOP button to turn the monitor off. NOTE: The monitor will automatically turn off after two minutes.
USING THE MEMORY FUNCTION Every time you complete a measurement the monitor stores the blood pressure and pulse rate for each user (A and B) in the memory. The monitor automatically stores up to 100 sets of measurement values (blood pressure and pulse rate) for each user (A and B). When 100 sets of measurement values are stored, the oldest record is deleted to save the most recent values.
USING THE MEMORY FUNCTION NOTES: • The date and time are alternately displayed with the measurement values. • Press the MEM button repeatedly to display the next values. • Press and hold the MEM button to display the values faster. 3. Press the START/STOP button to turn the monitor off. TO DELETE ALL VALUES STORED IN THE MEMORY The values stored in the memory are deleted by User ID. You cannot partially delete values stored in the memory. All values for the user you select will be deleted. 1.
CARE AND MAINTENANCE To keep your digital blood pressure monitor in the best condition and protect the unit from damage, follow the directions listed below: Do not forcefully bend the cuff. Do not fold tightly. Clean the monitor with a soft dry cloth. Do not use any abrasive or volatile cleaners. Do not attempt to clean the cuff. CAUTION Do not submerge the device or any of the components in water. Do not subject the monitor to extreme hot or cold temperatures, humidity or direct sunlight.
ERROR INDICATORS SYMBOL CAUSE CORRECTION Take another measurement and remain still until the measurement is complete. Monitor could not detect pulse wave. Cuff under-inflated. Cuff not applied correctly. Remove the monitor from your wrist. Read “Taking a Measurement”. Cuff over-inflated. Wait 2-3 minutes. Take another measurement. Device error. Contact Customer Service. Movement during measurement. Keep still and take another measurement. Irregular or weak pulses are detected.
TROUBLESHOOTING TIPS PROBLEM CAUSES AND SOLUTIONS No power. No display appears on the unit. Replace both batteries with new ones at the same time. Check the battery installation for proper placement of the battery polarities. Measurement values appear too high or too low. Blood pressure varies constantly. Many factors including stress, time of day, how you wrap the cuff, may affect your blood pressure. Review the sections “Before Taking a Measurement” and “Taking a Measurement”.
FCC STATEMENT Note: POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only) This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
LIMITED WARRANTY Your BP652 IntelliSense® Automatic Wrist Blood Pressure Monitor, excluding the wrist cuff and batteries, is warranted to be free from defects in materials and workmanship appearing within 5 years from the date of purchase, when used in accordance with the instructions provided with the monitor. The above warranties extend only to the original retail purchaser. We will, at our option, repair or replace without charge any monitor or wrist cuff covered by the above warranties.
SPECIFICATIONS Model: Display: Measurement Range: Accuracy/Calibration: Inflation: Deflation: Rapid Air Release: Measurement Method: Power Source: Battery Life: Operating Temperature /Humidity: Storage Temperature / Humidity/Air Pressure: Main Unit Weight: Main Unit Dimensions: Measurable circumference of wrist: Memory: Contents: BP652 (HEM-6052-Z) LCD Digital Display Pressure: 0 to 299 mmHg, Pulse: 40 to 180/min.
OMRON HEALTHCARE, INC. 1925 West Field Court Lake Forest, IL 60045 U.S.A. www.omronhealthcare.com © 2011 OMRON HEALTHCARE, INC.
