HEM-7300 e-s r2.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 2 TABLE OF CONTENTS Before Using the Monitor Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Operating the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 3 Before Using the Monitor INTRODUCTION Thank you for purchasing the Omron® Elite 7300W IntelliSense® Women’s Advanced Automatic Blood Pressure Monitor. Fill in for future reference. DATE PURCHASED: __________________ SERIAL NUMBER: ____________________ Staple your purchase receipt here Your new digital blood pressure monitor uses the oscillometric method of blood pressure measurement.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 4 SAFETY INFORMATION To assure the correct use of the product basic safety measures should always be followed including the warnings and cautions listed in this instruction manual. SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 5 SAFETY INFORMATION OPERATING THE DEVICE (continued) This device is intended for use in measuring blood pressure and pulse rate in the adult population. Do not use this device on infants or persons who cannot express their intentions. Inflating to a higher pressure may result in bruising where the cuff is applied. Operate the device only as intended. Do not use the device for any other purpose.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 6 SAFETY INFORMATION CARE AND MAINTENANCE Do not subject the monitor to strong shocks, such as dropping the unit on the floor. Do not submerge the device or any of the components in water. Store the device and the components in a clean, safe location. Changes or modification not approved by Omron Healthcare will void the user warranty. Do not disassemble or attempt to repair the unit or components.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 7 BEFORE TAKING A MEASUREMENT To ensure a reliable reading follow these recommendations: 1. Avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes before taking a measurement. Rest for at least 15 minutes before taking the measurement. 2. Stress raises blood pressure. Avoid taking measurements during stressful times. 3. Measurements should be taken in a quiet place. 4. Remove tight-fitting clothing from your arm. 5.
HEM-7300 e-s r2.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 9 KNOW YOUR UNIT Components: Arm Cuffs Air Tube Air Tube Air Plug (Connects to Air Jack) Air Plug (Connects to Air Jack) Standard Arm Cuff Large Arm Cuff Stylish Zipper Case Four “AAA” Batteries QUICK GUIDE Thank you for purchasing the Omron¤ Elite 7300W IntelliSense¤ Women s Advanced Automatic Blood Pressure Monitor. INSTRUCTION MANUAL There are two cuffs included in this unit, standard size and large size.
HEM-7300 e-s r2.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 11 DISPLAY SYMBOLS IRREGULAR HEARTBEAT SYMBOL ( ) When the monitor detects an irregular rhythm two or more times during the measurement, the Irregular Heartbeat Symbol ( ) will appear on the display with the measurement values.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 12 DISPLAY SYMBOLS HEARTBEAT SYMBOL/HYPERTENSION INDICATOR ( ) TAKING A MEASUREMENT The Heartbeat Symbol ( ) flashes on the display during the measurement. The Heartbeat Symbol ( ) flashes at every heartbeat. When the measurement is complete, the Heartbeat Symbol ( ) flashes on the display with your blood pressure and pulse rate if the reading is above 135 for the Systolic Blood Pressure value and/or 85 for the Diastolic Blood Pressure value.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 13 DISPLAY SYMBOLS The American Heart Association recommends the following guideline for upper limit of normal for home blood pressure readings: AHA Home Guideline for Upper Limit of Normal BP Systolic Blood Pressure 135 mmHg Diastolic Blood Pressure 85 mmHg This is a general guideline because blood pressure depends on age and morbidity.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 14 BATTERY INSTALLATION t 1. Press the indicator on the battery cover and slide the cover off in the direction of the arrow. Battery Cover 2. Install 4 “AAA” size batteries so the + (positive) and – (negative) polarities match the polarities of the battery compartment as indicated. 3. Replace the battery cover.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 15 BATTERY INSTALLATION BATTERY REPLACEMENT Low Battery Indicator When the Low Battery Indicator appears on the display screen, turn the monitor off and remove all the batteries. Replace with four new batteries at the same time. WARNING If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Contact a physician immediately. NOTES: • Turn the unit off before replacing the batteries.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 16 SETTING THE DATE AND TIME Set the monitor to the current date and time before taking a measurement for the first time. If the date and time are not set correctly, the measurement values stored in the memory and the average values may not be correct. The Blood Pressure Monitor automatically stores up to 84 individual measurements values with the dates and times.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 17 SETTING THE DATE AND TIME 2. SETTING THE YEAR The year can be set between 2008 and 2030. When the display reaches 2030, it will return to 2008. Press the Memory button ( increments of one year. ) to advance by Press the Date/Time Setting button ( to set the current year. ) The month flashes on the display. NOTE: Press and hold the Memory button ( time values faster. ) to advance the date and 3.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 18 SETTING THE DATE AND TIME 4. SETTING THE DAY Press the Memory button ( ) to advance by increments of one day. Press the Date/Time Setting button ( ) to set the current day. The hour flashes on the display. 5. SETTING THE HOUR The time is set using AM or PM. Press the Memory button ( ) to advance by increments of one hour. Press the Date/Time Setting button ( ) to set the current hour. The minute flashes on the display. 6.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 19 SETTING THE DATE AND TIME RESETTING THE DATE AND TIME To adjust the date or time after it has been setup when you first use the unit. Start with the monitor in the off position. 1. Press and hold the Date/Time Setting button ( ). The Medication Symbol ( ) No.1 and the current setting (on or oFF) will appear on the display. Press the Date/Time Setting button repeatedly until the year flashes on the display. 2. Refer to “Setting the Date and Time”.
HEM-7300 e-s r2.qxd 11/5/07 12:48 PM Page 20 SETTING THE MEDICATION REMINDER ALARM The Medication Reminder Alarm can be set to sound twice a day to alert the user to take a medication. The Medication Reminder Alarm can be set for either AM or PM alerts. Only set the Medication Reminder Alarm after the date and time has been set. The Medication Reminder Alarm is set to off at the time of purchase. NOTES: • Press the START/STOP button to stop the Medication Reminder Alarm.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 21 SETTING THE MEDICATION REMINDER ALARM 2. SETTING ON OR OFF Press the Memory button ( ) to select on. Press the Date/Time Setting button ( ). The hour flashes on the display. NOTE: Press the Memory button ( ) to alternate between on or oFF. 3. SETTING THE HOUR The time is set using AM or PM. Press the Memory button ( ) to advance by increments of one hour. Press the Date/Time Setting button ( to set the hour. The minute flashes on the display.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 22 SETTING THE MEDICATION REMINDER ALARM 4. SETTING THE MINUTE Press the Memory button ( minute. ) to advance by increments of one Press the Date/Time Setting button ( ) to set the minute. The Medication Symbol ( ) No.2 and the oFF setting appears on the display. 5. SETTING THE MEDICATION REMINDER ALARM 2 Repeat steps from 2 to 4 to set the Medication Reminder Alarm 2. The year flashes on the display, after the Medication Reminder Alarm 2 has been set.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 23 SETTING THE MEDICATION REMINDER ALARM 6. TO TURN THE MONITOR OFF If the date and time are correct, press the START/STOP button to turn the monitor off. To change the date and time refer to “Resetting the Date and Time” on page 19.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 24 APPLYING THE ARM CUFF CAUTION Read all of the information in the instruction manual and any other literature in the box before operating the unit. CAUTION This device is intended for use in measuring blood pressure and pulse rate in the adult population. Do not use this device on infants or persons who cannot express their intentions. USE CUFF GUIDE TO CHOOSE THE RIGHT CUFF There are two cuffs included in this unit, standard size and large size.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 25 APPLYING THE ARM CUFF 2. Fit the looped Cuff Guide on your upper arm. 3. Cuff Guide shows your correct cuff. Use the cuff with same colored sticker. Orange Use the Standard Cuff Use the Large Cuff Purple APPLYING THE CUFF ON THE LEFT ARM 1. Make sure the air plug is securely inserted in the main unit.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 26 APPLYING THE ARM CUFF 2. Remove tight-fitting clothing from your upper left arm. 3. Apply the cuff to your left upper arm so the blue arrow is centered on the inside of your arm and aligned with your middle finger. The air tube runs down the inside of your arm. The bottom of the cuff should be approximately 1/2" above your elbow. 1/2 inch (1 - 2 cm) Blue Arrow 4. Wrap the cuff firmly in place around your arm using the closure strip.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 27 APPLYING THE ARM CUFF APPLYING THE CUFF ON THE RIGHT ARM When taking a measurement using the right arm use this instruction for Step 3 on page 26. Apply the cuff to your right upper arm so the blue arrow and the air tube runs along the inside of your elbow. The bottom of the cuff should be approximately 1/2'' above your elbow. NOTE: Be careful not to rest your arm on the air tube. This will restrict the flow of air to the cuff.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 28 TAKING A MEASUREMENT 1. Sit in a chair with your feet flat on the floor. Place your left arm on a table so the cuff is level with your heart. 2. Press the START/STOP button. All symbols appear on the display. The cuff starts to inflate automatically. As the cuff inflates, the monitor automatically determines your ideal inflation level. This monitor detects your blood pressure and pulse rate during inflation.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 29 TAKING A MEASUREMENT 3. When the measurement is complete, the arm cuff completely deflates. Your blood pressure and pulse rate are displayed. 4. Press the START/STOP button to turn the monitor off. NOTE: The monitor will automatically turn off after two minutes.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 30 TAKING A MEASUREMENT USING THE GUEST MODE The monitor is designed to take measurements and store the measurement values in the memory for one person. The monitor can also be used to take a single measurement for other persons using the GUEST Mode. Measurements taken using the Guest Mode are not stored in the memory. 1. Press and hold the START/STOP button for 3 seconds. The Guest Symbol ( display. ) appears on the 2. Release the START/STOP button.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 31 USING THE MEMORY FUNCTION Every time you complete a measurement the monitor stores the blood pressure and pulse rate in the memory. The monitor automatically stores up to 84 sets of measurement values (blood pressure and pulse rate). When 84 sets of measurement values are stored, the oldest record is deleted to save the most recent values. Measurements taken using the GUEST Mode are not stored in the memory.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 32 USING THE MEMORY FUNCTION 2. Press the Memory button ( ) to display the most recent set of measurement values on the screen. The values are displayed from the most recent to the oldest. NOTE: The date and time are alternately displayed with the measurement values. Press the Memory button ( ) to display the next set of values. Press and hold the Memory button ( ) to display the values faster. Alternating display 3.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 33 USING THE MEMORY FUNCTION TO DELETE ALL VALUES STORED IN THE MEMORY You cannot partially delete values stored in the memory. 1. Press the Memory button ( ) to turn the monitor on. 2. Press the Memory button ( again. ) While holding it down, press the START/STOP button together for more than 5 seconds. 3. Press the START/STOP button to turn the monitor off. NOTE: The monitor will automatically turn off after two minutes.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 34 Care and Maintenance CARE AND MAINTENANCE To keep your digital blood pressure monitor in the best condition and protect the unit from damage, follow the directions listed below: Keep the monitor in the Stylish Zipper Case when not in use. Do not forcefully bend the arm cuff or air tube. Do not fold tightly. Clean the monitor with a soft dry cloth. Do not use any abrasive or volatile cleaners. Do not attempt to clean the cuff.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 35 CARE AND MAINTENANCE Use the unit consistent with the instruction provided in this manual. CAUTION Changes or modification not approved by Omron Healthcare will void the user warranty. Do not disassemble or attempt to repair the unit or components. CAUTION Use only Omron authorized parts and accessories. Parts and accessories not approved for use with the device may damage the unit.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 36 ERROR INDICATORS AND TROUBLESHOOTING TIPS ERROR INDICATORS SYMBOL CAUSE CORRECTION Remove the arm cuff. Read, “Taking a Measurement”. Take another measurement. Cuff over-inflated Monitor could not detect pulse wave. Take another measurement and remain still until the measurement is complete. Air plug is not connected. A malfunction has occured. Contact your OMRON distributor or Customer Services as mentioned on the package.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 37 ERROR INDICATORS AND TROUBLESHOOTING TIPS TROUBLESHOOTING TIPS PROBLEM CAUSES AND SOLUTIONS No power. Replace all four batteries with new ones. No display appears on the unit. Check the battery installation for proper placement of the battery polarities. Measurement values appear too high or too low. Blood pressure varies constantly. Many factors including stress, time of day, and how you wrap the cuff, may affect your blood pressure.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 38 FCC STATEMENT NOTE: POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only) This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 39 WARRANTY ® Your Omron Elite 7300W IntelliSense® Women’s Advanced Automatic Blood Pressure Monitor, excluding the arm cuffs, is warranted to be free from defects in materials and workmanship appearing within 5 years from the date of purchase, when used in accordance with the instructions provided with the monitor.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 40 SPECIFICATIONS Model: Display: Measurement Range: Accuracy/Calibration: Inflation: Deflation: Rapid Air Release: Pressure Detection: Measurement Method: Pulse Wave Detection: Power Source: Battery Life: Elite 7300W LCD Digital Display Pressure: 0 to 299 mmHg, Pulse: 40 to 180/min.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Page 41 SPECIFICATIONS Memory: Contents: UPC Code: Up to 84 readings Main Unit, Standard and Large Arm Cuffs, Instruction Manual, 4 “AAA” batteries, Stylish Zipper Case, Quick Guide, Warranty Card and Cuff Guide 0 73796 73000 0 NOTE: These specifications are subject to change without notice.
HEM-7300 e-s r2.qxd 11/2/07 4:50 PM Manufactured by OMRON HEALTHCARE Made in China Distributed by: OMRON HEALTHCARE, INC. 1200 Lakeside Drive Bannockburn, Illinois 60015 www.omronhealthcare.com Copyright © 2007 Omron Healthcare, Inc.
