Owner's Manual

on-Q
a legrancf
INSTRUCTION I INSTALLATION SHEET
Home
Entertainment Connection
Center (HECC 7.1)
301 Fulling Mill Road, Suite G
Middletown. PA 17057
Phone (BOO) 321-23431 Fax [phone]
www.onqlegrand.com
18-0357 Rev. 0
2. Description
The HECC comes with a lyriO"" Source Input Mounting Plate (PIN 364886-01) installed that enables the
use of a lyriO"" Single or Triple Source Input Unit (see Figure 2).
1 IntrOduction
On.QJlegralld offers a Home Entertainment Connection Center (HECe) (PIN HT1000) which provides an
attractive, convenient interface
to your entertainment center (see Figure 1). The HECC provides a single
connection pomt for all the remole cabling used in most home entertainment centers, including phone,
video, and data connections. Additional whole house distributed audio can
be interfaced with the On-
Q/legrand lyriQ 1M Audio system or traditional speaker level audio distribution system wIth the 6 Room
Audio Module. The HECC is recess mounted and provides a low profile interface which Includes a cover
thai hides unsighUy wife connections and aids in wire management.
Figure 1
with 1yr\Q" Triple
Source Input Un"
(nolln~llIded)
".
." .
••
• • ,"" 1U
- •• ".1 •
Iyr\Q"Souttt
Input Ilklunting
Figure 2
The HECC has a built in interface board for pre-wired Home Theater cabling (5.1, 6.1, 7,1). Also included is one universal Keystone style
phone RJ45 Insert, data RJ45 Insert, and three feed through
-F" connector inserts for CATV. AUX, and Satellite. Additional universal Keystone
Inserts can
be added for increased functionality.
The
HECC employs a "User side" (front) and an "Installer side" (rear) designed to simplify wire terminations. The "User side" allows easy
access to telephone. data. CATV. DSS. and audio connection pomts.
The "Installer side" allows easy access to the rear connection points by
rotating the top portJon
01 the HECC outward and downward thus displaying readable connection diagrams. The cover is an attractive white
powder coated metal which allows cable access through the bottom and includes an installed plunger for quick access.
3. Installation
Installation of the On-QJLegrand HECC 7.1 is best accomplished at multiple times during new construction, at "Rough-in" before the drywall is
installed. and
at "Trim-out" aher the drywall is installed and painted.
NOTE: Please
refer to the lyriO"" Source Input Unit InstructIon Sheets (15-0319 and 15-0326) for additional module-specific
installation instructions (if applicable).
NRough-in" Steps
A. The HECC should be located near the home enlertamment area considering home owner access
needs, wiring, and cabling. Preferably
It will be in a full stud cavity (16" center) and the stud cavity
should
not be shared With HVAC, plumbing, or major high voltage cabling. Typical installation will be
centered on a wall.
If the preferred mounting height is unknown, the HECC should be mounted at
outlet height.
B. Mounlthe pre-construclion bracket (see Figure 3) to the studs With drywall screws, with the flanges
()(I the frame pointed out toward the drywall. Keep the brackel level to assure proper appearance
when installation is complete.
Figure 3
NOTE: The HECC is not firewall rated and should not be mounted in designated firewalls.
C. Cable Rough-in:
1) Surround Sound pre-wire (if applicable): 16/2
or 14/2 speaker wire should be Nn from the HECC location to eaCh In-wall/ln-Ceiling
speaker pre-construction bracket location, leaving extra cabte I'll bolh ends. The provided Speaker Brackets
may be used to identlry
the
exacllocalion or the speakers. There are clips on the speaker brackets to secure a coil of speaker wire. which will be connected
to the speaker at trfm-oul.
OCopyright 2006
by On-O/Legrand AU Rights Reserved.
Page 1
of 3