Owner's Manual
Table Of Contents
onoQ
DlegrandO
INSTRUCTION I INSTALLATION SHEET
Home
Entertainment
Connection
Center
(HECC 7.1)
301 FuUing Mill Road, Suite G
Middletown,
PA
17057
Phone (800) 321-23431 Fax (717) 702-2546
www.onqlegrand.com
15-0357 Rev. 0
2) One RG6QS cable should be run from a single gang outlet box or mud ring at the desired sub-woofer location
10
the HECC location.
leaving extra cable
at
both ends.
NOTE:
The
number
of
speaker
wire
runs
will
vary
depend1ng
upon
which
theater
format
is
being
utilized.
3)
Alleasl
one RGSaS cable and two Cat
5e
cables should
be
run in the wall from the HECC location to the structured wiring
enclosure. leaving extra cable at both ends. Clearly label each cable as it is installed.
NOTE: The RG6QS cable Is
for
normal
distributed
TV service.
If
Satellite service Is planned,
additional
cables
may
need to
be
run. The
two
Cat 5e
cables
are
for
phone
and
data
services.
4) 6 Room Audio pre-wire (if applicable): run 16/4 or 14/4 high quality speaker wire from the HECC location to lhe volume control
locations and 16/2 or 14/2 from the volume control locations to each speaker location, leaving extra cable at both ends. Clearly label
each cable as il is installed,
5) lyriC"'" pre-WIre (if applicable): run
Cal5e
cable from the HECC location to lhe structured wiring enclosure, leaving extra cable
at
both ends. Clearly label each cable as it is installed. Complete pre-wire
of
lyriQ
"'"
system
petlyriQ
TloI
instructions.
NOTE:
Always
mark
cables
at
both
ends
for
easy
identification
at
trlm-out.
Figure 4
NOTE:
Follow
this
pattern
for
proper
surround
sound
speaker
connections
to
the
User
side
(5.5,5,5,5,6,7,.1): A)
for
5.1
connect
wires
to
connectors
labeled
~5~
and
".1",
B)
for
6.1
connect
wires
to
connectors
labeled
"5~
and
"6"
and
",1",
C)
for
7.1
connect
wires
to
connectors
labeled
"5"
and
"6"
and
"7"
and
".1"
Surround
sound
speakers are
usually
mounted
on the sides
of
the
room
and
not
the
rear.
For
5.1, the
left
and
right
speakers
would
be
mounted
on
the
left
and
right
hand
sides.
For
6,1, the speakers
would
be
mounted
on the left
and
right
sides
and
the
3rd
speaker
would
be
mounted
In
the
center
rear.
For
7.1
the speakers
would
be
mounted
on
the left
and
right
sides
and
the
two
additional
speakers
mounted
in
the
left
rear
and
right
rear
positions
(see
Figures
5,6,7). In
many
situations
it
is
necessary
or
desired
to
substitute
rear
positions
for
the
normally
side
mounted
surrounds.
"Trim-out"
Steps
A.
At the HECC location. pull the RG6QS and speaker wires through the HECC mounting
bracket. Tenninate
lhe
RG6QS cables
With
"F" connectors and attach to the appropriate
connectors for distributed TV service and sub-woofer service. The Surround Sound speaker
wires should
be
terminated
at
the screw tenninals on the back of the HECC
In
accordance
With
the appropriate speaker locations (5.1. 6.1. 7.1) as indicated
on
the HECC (see
Figure
4).
B.
If
uSlOg
phone and data. terminate the Cat
Se
cables from the structured wiring enclosure on the
universal Keystone RJ45 Jack Inserts and snap them into the back
of
the HECC.
C.
Terminate any RG6QS cables
With
OF-
connectors and attach them
to
the
"F"
feed through Inserts on the back
of
the HECC.
D.
If using a 6 Room Audio Module. terminate the speaker wires from the impedance matching volume conlrols at lhe
SCfew
terminals on
the back
of
the HECC (see Figure
4).
E If using a lyriC"'" system. terminate
the
Cat 5e cable from Ihe structured wiring enclosure on a universal Keystone RJ45 Jack Insert and
snap the Insert into the back
of
the HECC. Using an RJ45 Jumper cable, such as PIN 363201-27, connect the lyriQ"'" Source Input jack
labeled 'Audio
OUI'
10 the RJ45 jack which carries the lyriC
'M
line le"'el Signal
to
the structured wiring enclosure.
F.
Once all cables are attached
to
the back
of
the HECC. secure the HECC insert
to
the HECC mounting bracket
uSing
4 drywall screws.
G.
If using 6 Room Audio module, terminate the left and right speaker wires from the audio amplifier at the Source In connectors on the 6
Room Audio Module. using
16/4 high quality speaker wire.
NOTE: Impedance
matching
volume
controls
must
be
used
to
prolect
the
audio
source
equipment.
@Copyright 2006 by On-Q/Legrand All Rlghls Reserved.
Page 2
of
3