Assembly Instructions
Assembly Instructions:
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Remove the old xture from the ceiling, including the old mounting
strap.
1. From the parts bag remove the mounting strap assembly. One end of
nipple (F) should be attached to mounting strap (A) with hex nut and washer
(C & D) in place. The other end should have canopy loop (H) attached. Attach
mounting strap (A) to the junction box using mounting screws (B) and a
screwdriver. Tighten securely.
2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over
the mounted canopy loop to test the height. Approximately half of the canopy
loop’s exterior threads should be exposed, and the canopy loop collar should
tsnuglyontothecanopyloop.Removecanopy(G)andadjusttheheightof
nipple (F) and canopy loop (H) until the desired height is reached. Remove
canopy (G) and canopy loop (H).
ASSEMBLING THE FIXTURE
Please Note: This xture may be hung as a pendant or semi-ush.
3.Forsemi-ushinstallationconnectonechainconnector(K)totoploop
(L) and canopy loop (H). Twist the side of chain connector (K) to close. For
pendant installation, determine the correct number of chain links needed for
proper hanging height. If necessary, use a pair of pliers to open and remove
any excess chain (J). Attach one chain connector (K) to each end of chain
(J). Twist the side lock to secure in place. Connect one of chain connectors
(K)totoploop(L)andclosethechainconnector.Feedthexture’swiresup
through the chain (every three links or so), pulling the wires until taut. Use the
free chain connector (K) to attach chain (J) to canopy loop (H).
4. Untwist canopy loop collar (I) to allow canopy (G) to be added to the chain
or chain connector. Allow canopy (G) to drop down onto the chain or chain
connector.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
5.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cutawayanyexcesswireaddingatleast8to10inches
ofwiretothedesiredlength.Threadthexture’swiresthroughcanopyloop(H)andnipple(F).Refertothewiringdiagramandattach
thexture’swirestothepowersupplywiresfromthejunctionbox.ConnectHottoHot,NeutraltoNeutral,andGroundtoGround.
Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is
no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the
xture’sgroundwirearoundthegroundscrew.Useascrewdrivertotightenthetopofgroundscrew(E)ontothewiresandintothe
mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
6. Push canopy (G) and canopy loop (H) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy
loop collar (I) onto canopy loop (H) to secure canopy (G) in place.
7. Place frame (N) over socket (M) and screw socket cover (O) onto the threads of socket (M).
8.Installalightbulb(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
N
M
O
A
B
C
D
E
F
G
H
I
J
K
L
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
N
M
A
B
C
D
E
F
G
H
I
K
L