WALRB4P manual booklet 5/2/06 3:16 PM Page 2 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Device Table . . . . . . . . . . . . . . . . . . . . . . .
WALRB4P manual booklet 5/2/06 3:16 PM Page 3 INTRODUCTION FEATURES AND FUNCTIONS The One For All 4 Device Universal Remote Control (URC-4220) is designed to remotely operate up to four home entertainment devices. It also features intuitive and easy-to-use keys for instant control of DVD and PVR (or DVR) components. Moreover, its sophisticated technology will allow you to consolidate your original home entertainment remote controls into one easy-to-use product.
WALRB4P manual booklet 5/2/06 3:16 PM Page 5 Key Charts Use REW, PLAY, FWD, PAUSE,or STOP to control your VCR, PVR (or DVR), or DVD player. When the LED (red light) blinks, the remote control is working and (after programming) is sending signals. For a DVD player, use SKIP F. or SKIP R. to view the next or previous chapter. Press VCR/PVR, DVD, CBL/SAT, or TV once to select a desired home entertainment device to control. Also see the Device Table on page 6.
WALRB4P manual booklet 5/2/06 3:16 PM Page 7 INSTALLING BATTERIES PROGRAMMING DEVICE CONTROL The One For All 4 Device Universal Remote Control is preprogrammed at the factory to operate an RCA TV, a Toshiba DVD player, a Motorola cable box, and an RCA VCR. To control devices other than the default brands, perform the following steps; otherwise skip this section: 1. Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc).
WALRB4P manual booklet 5/2/06 3:16 PM Page 9 SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. 5. Repeat step 4 (on the previous page) three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.Write down the code digits in the remaining TV code boxes on page 8. 6.
WALRB4P manual booklet 5/2/06 3:16 PM Page 11 PROGRAMMING A MASTER POWER MACRO (continued) 2. • If Favorite Channel Scan has been set up,scanning of favorite channels will start with up to 100 channel changes or until stopped by pressing any key. Clearing The Master Power Macro 1. 2. Press FAV once. Press and hold SET until the LED (red light) blinks twice, then release SET.
WALRB4P manual booklet 5/2/06 3:16 PM Page 13 CHANGING VOLUME LOCK The One For All 4 Device Universal Remote Control is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a device’s volume will be locked to one mode (e.g., to control TV volume in all other modes).After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.
WALRB4P manual booklet 5/2/06 3:16 PM Page 15 TROUBLESHOOTING INSTRUCTIONS TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation.
