Producer 2002 IR Mnl 4/4/02 10:01 AM Page 1 A/V LCD 8-DEVICE WITH LEARNING UNIVERSAL REMOTE CONTROL (URC-8910) User’s Guide
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 2 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting The Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features And Functions . . .
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 3 INTRODUCTION The One For All A/V LCD 8-Device With Learning Universal Remote Control (URC-8910) is our latest high-performance universal remote control. It is designed to operate up to eight home entertainment devices, including TV, video, and audio components. Moreover, this remote control contains sophisticated technology that will allow you to conveniently consolidate the clutter of all of the original remote controls used in your home entertainment system.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 4 INSTALLING BATTERIES ❶ ❷ ❸ 1. On the back of the URC-8910 remote control, push the tab and lift off the battery cover. 2. Obtain four (4) new AAA alkaline batteries. Match the + and – marks on the batteries to the + and – marks in the case, and then insert the new batteries. 3. Align the cover key with the case opening and replace the cover until it locks. 4. If batteries are inserted correctly, the entire LCD will turn on.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 5 SETTING THE CLOCK 1. On the URC-8910 remote control, press and hold SET until you see the display change from the default device and time to [CODE SET]. NOTE: Default values for device, its code, and time are shown above.Your remote control settings may be different. NOTE: If you wish to exit the programming mode at any time, press EXIT once. You will see an [EXIT] message as the remote control returns to normal operation.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 6 FEATURES AND FUNCTIONS Use the illustration below to locate features on the URC-8910 remote control and then study the Key Charts (on the next three pages) to learn how they function.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 7 Key Charts The LED (red light) blinks to show that the remote control is working and sending signals. The LCD (Liquid Crystal Display) provides 15 alphanumeric characters that display status messages during remote control operation and programming.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 8 FEATURES AND FUNCTIONS Key Charts (continued) Use EXIT to exit from your selected device’s guide or menu. Use INFO to display the current channel and program information. Use VOL+ (or VOL-) to raise (or lower) the audio volume. Press MUTE once to turn the audio off or on. In the TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels.See Using Channel Scan and Programming Favorite Channel Scan on page 41.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 9 Use the transport keys to control your VCR,DVD or CD player,or VOD (Video On Demand) if available on your cable or satellite service. To record a VCR program, press REC twice. Use SLEEP to activate your device’s sleep timer (not available for all devices). After programming, press M1 ~ M3 once to run a desired macro (see Using Macros on page 34). After programming, press L1 ~ L4 once to activate a learned function. See Using Learning on page 30.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 10 PROGRAMMING DEVICE CONTROL The URC-8910 remote control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable converter, an RCA satellite receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer audio receiver/ amplifier, and a One For All home automation device.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 11 For example, to enter the first GE VCR code (on page 24), press 0 twice, 6 once, 0 once, and then SELECT once. If the code is entered correctly, you will see the [SUCCESS] message. 6. Press EXIT to exit the programming mode.You will see an [EXIT SETUP] message as the URC-8910 remote control returns to normal operation. 7. To verify the code works, aim the URC-8910 remote control at the desired device, press its device key once and then press POWER once.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 12 PROGRAMMING TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette. NOTE: Please read steps 2 through 9 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2. 2. On the URC-8910 remote control, press and hold SET until you see the display change from the current device and time to [CODE SET].
Producer 2002 IR Mnl 6. 4/4/02 10:01 AM Page 13 (Optional) Skip this step if your TV/VCR Combo does not have a separate TV code. Otherwise, press TV once.You will see the display change to [TV] and its current code. Use the keypad to enter the separate TV code for your device. 7. Press EXIT to exit the programming mode.You will see [EXIT SETUP] as the URC-8910 remote control returns to normal operation. 8.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 27 SEARCHING FOR YOUR CODE If your device does not respond to the URC-8910 remote control after trying all codes listed for your brand, or if your brand is not listed at all, try manually searching for your code. For example, to manually search for a code for your TV: 1. Turn on the TV. 2. On the URC-8910 remote control, press and hold SET until you see the display change from the current device and time to [CODE SET].
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 28 SEARCHING FOR YOUR CODE (continued) NOTE: In the manual search mode, the URC-8910 remote control will send IR codes from its library to the selected device, starting with the most popular code first. 7. If the device (e.g., TV) turned off, skip to the next step. If it did not turn off, aim the URC-8910 remote control at the device (e.g., TV) and press the ▲ key once to advance the manual search to the next code (e.g., TV and 0054).
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 29 USING LEARNING Program the learning keys (L1~ L4) to add functions that are unique to your home entertainment devices (e.g.,VCR Tracking Up or Down). However, there are some considerations: • Your original remote control must be in working order for the learning feature to work properly. • Learned keys are mode specific, so each one can store a unique function for each mode. • Learned keys can be used in macros (see Using Macros on page 34).
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 30 USING LEARNING Programming A Learning Key (continued) 4. Press a device key once (e.g., TV) to assign a desired mode for learning. 5. Select an open learning key (e.g., L1) and press it once.You will see the display change to [LEARNING] and the LED (red light) will turn on for 5 seconds. 6. Place your original remote control (e.g., TV remote control) head-to-head (about 2" apart) from the URC-8910 remote control. 2" 7.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 31 where the learned feature is stored. The feature should activate. If not, try the programming the learning key again, starting with step 1 (on page 29). Deleting A Function From A Learning Key 1. On the URC-8910 remote control, press and hold SET until you see the display change from the current device and time to [CODE SET]. NOTE: The device, its code, and time are examples. Your remote control settings may be different.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 32 USING VOLUME LOCK In its default (unlocked) state, the URC-8910 remote control allows each device to control its own volume only in its own mode (e.g., TV volume in the TV mode, VCR volume in VCR mode, etc.). However, using our Volume Lock feature, you can lock the volume controls for each device to all modes (e.g., RCVR/AMP volume in all modes).
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 33 Programming Volume Unlock 1. 2. On the URC-8910 remote control, press and hold SET until you see the display change from the current device and time to [CODE SET]. (x 5) Press the ▼ key five times until you see the display change to [VOL UNLOCK]. NOTE: If you go past [VOL UNLOCK], press the ▲ key one or more times to return to it. Press SELECT once to begin programming.You will see the display change to [ALL MODE]. 3.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 34 USING MACROS With programming, the M1 through M3 keys on your URC-8910 remote control can be setup to perform repetitive, time-consuming operations for easy, convenient access through the press of a single key. Macro keys are ideal for home theater operations, setting a favorite channel, guide steps, or other multiple functions you would like to control with one key press. Moreover, each macro key can hold up to15 key presses total.
Producer 2002 IR Mnl 5. 4/4/02 10:01 AM Page 35 Enter a macro sequence of up to 15 keys. For our example, press the following keys once in this order: TV - 7- 1 NOTE: If you have access to over 100 channels, add a 0 before the channel numbers (e.g., 0-7-1). If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0-7-1-ENTER).
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 36 USING MACROS Programming A Master Power Key With Instant Channel Selection (continued) NOTE: An [ERROR] message, followed by [MAX = 15] alerts you that the macro sequence must be 15 keys or less. 3. After pressing the first key (in the macro sequence), you will see the display change to [SEL TO END]. This message acts as a reminder to use SELECT to end the sequence (see next step). 4.
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 37 RE-ASSIGNING DEVICE KEYS The URC-8910 remote control can control a second TV,VCR, DVD player, or other device by using the Mode Map feature. For example, to control a TV, a cable converter, and two VCRs, you will need to reassign the unused AUX key to operate the second VCR as follows: 1. On the URC-8910 remote control, press and hold SET until you see the display change from the current device and time to [CODE SET].
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 38 RE-ASSIGNING DEVICE KEYS (continued) To re-assign other device keys to the AUX key, repeat steps 1 through 6 on the previous page but substitute the key sequence from the below chart: To Re-Assign Device Key Perform Sequence AUX as 2nd TV key: SET*- ▼ (x 7) - SELECT - TV - AUX AUX as 2nd DVD key: SET*- ▼ (x 7) - SELECT - DVD- AUX AUX as 2nd SAT key: SET*- ▼ (x 7) - SELECT - SAT- AUX AUX as 2nd CD key: SET*- ▼ (x 7) - SELECT - CD- AUX AUX as 2nd CBL
Producer 2002 IR Mnl 4/4/02 10:01 AM Page 39 NOTE: If you go past [KEYMOVER], press the ▲ key one or more times to return to it. 3. Press SELECT once to begin programming.You will see the display change to [FROM MODE]. 4. Select a source mode (e.g., TV) and press it once.You will see the display change to [FROM KEY]. 5. Select a source key (e.g., VOL+) and press it once. You will see the display change to [TO MODE]. 6. Select a destination mode (e.g., VCR) and press it once.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 40 USING KEYMOVER Restoring Keymoved Keys to Default Settings Restoring A Single Keymoved Key (continued) 2. Press SELECT once to clear the keymoved key.You will see [DELETED] appear in the display, followed by [EXIT SETUP]. The URC-8910 remote control will automatically exit the programming mode and return to normal operation. Restoring All Keymoved Keys In A Single Mode 1. Perform steps 1 through 4 of the earlier section, Programming Keymover on page 38.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 41 USING CHANNEL SCAN In the TV, VCR, DVD, SAT, and CBL modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed – see Programming Favorite Channel Scan below) and/or all channels for the selected mode. 1. If Favorite Channel Scan has been set up, skip to step 2. Otherwise, on the URC-8910 remote control press TV, VCR, DVD, SAT, or CBL once. 2. Press FAV once.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 42 PROGRAMMING FAVORITE CHANNEL SCAN (continued) 2. (x 4) Press the ▲ key four times until you see the display change to [FAV CHAN]. NOTE: If you go past [FAV CHAN], press the ▼ key one or more times to return to it. 3. Press SELECT once to begin programming.You will see the display change to the last-selected device (e.g., [VCR]). 4. Select a mode (e.g., TV) for favorite channel scanning and press it once. Then press Press SELECT once.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 43 USING THE HOME THEATER MODE The URC-8910 remote control includes a custom Home Theater mode.After the HOME THEATER key is programmed, it will allow you to access five groups of remote control keys without having to change device modes. However, there are some considerations. • Keymoved and Learned functions, as well Macros programmed onto keys other than the dedicated macro keys (M1 ~ M3), are affected by the Home Theater mode.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 44 USING THE HOME THEATER MODE Control Organization About Device Groups (continued) The default Device Group settings from the factory is: (1) Playback Group: VCR (2) Audio Group: TV (3) Channel Group: CBL (4) Menu Group: CBL (5) PIP Group: TV Programming The Home Theater Mode For example, let’s assume you have a TV, a cable converter, and a VCR in your home theater system.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 45 a. Press SELECT once to enter Playback Control Group assignment.You will see the display change to the last-selected device (e.g., [TV]). b. Select a device for Playback Control Group assignment. For this example, press VCR once. This will assign the entire group of Playback Controls (i.e., PLAY, STOP, FF, REW, F.FWD, F.REW, PAUSE, and REC) to the VCR.You will see the display change to your device choice (e.g., [VCR]). c.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 46 USING THE HOME THEATER MODE Programming The Home Theater Mode 5. (continued) a. Select a device for Channel Control Group assignment. For this example, press CBL once. This will assign the entire group of Channel Controls (i.e., CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, and TV/VID) to the cable converter. You will see the display change to your device choice (e.g., [CBL]). b. Press SELECT once to accept the assignment in step 5b.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 47 b. Press SELECT once to accept the assignment in step 7a.You will see the display change to the first Control Group assignment, [PLAYBACK]). 8. or At this point, all Control Groups have been assigned. To change an assignment, use the ▲ or ▼ keys to navigate to a specific group and make changes by repeating the appropriate step (3, 4, 5, 6, or 7).
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 48 USING COMMERCIAL SKIP The URC-8910 remote control includes a unique Commercial Skip feature, once programmed, that will allow you to skip viewing commercials by pressing the COM SKIP key. Then, as you change channels (to view another program without commercials), an internal timer will count down a preset time interval before returning the device to the original channel.
Producer 2002 IR Mnl 5. 6. or 4/4/02 10:02 AM Page 49 If desired, press ▲ (or ▼) one or times to select a different time interval.Your choices are 30 (default), 60, 90, 120, 150, or 180 seconds. For this example, select 60 seconds. Press SELECT once to accept the 60-second setting. You will see [SUCCESS] appear in the display, followed by [EXIT SETUP]. The URC-8910 remote control will automatically exit the programming mode and return to normal operation.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 50 RESTORING FACTORY DEFAULT SETTINGS The URC-8910 remote control includes an Operation Reset program that you can use to restore the unit to factory default settings. IMPORTANT: Executing this program will erase all custom settings, including Home Theater assignments, Macros, Learned Keys, Keymoved Keys, and all device assignments. 1.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 51 ABOUT UPGRADING The URC-8910 remote control has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control’s memory. If this happens, please contact our Customer Support department (see Customer Support on page 74) to upgrade the URC-8910 remote control.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 52 TROUBLESHOOTING PROBLEM: LCD (Liquid Crystal Display) begins to fade, does not appear, or the LOW BATTERY ( )icon appears. SOLUTION: Replace the batteries with four (4) new AAA alkaline batteries (see page 4). PROBLEM: LED (red light) and IR ( ) icon blinks when you press a key, but home entertainment device does not respond. SOLUTION: Be sure to select the correct device key for the device you want to control.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 53 PROBLEM: Tried Search For Your Code method and still could not find a working code. SOLUTION: Your device may be newer than the URC-8910 remote control. See About Upgrading on page 51. PROBLEM: Your satellite (DSS) receiver does not respond to the codes listed on page 18. SOLUTION: Make sure the satellite (DSS) receiver can be operated with an Infrared (IR) remote control and is not set up to receive only Radio Frequency (RF) signals.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 54 KEY INDEX Audio Amplifier Functions Press RCVR/AMP once to control your audio amplifier. Press POWER once to turn on or off the selected device (e.g, RCVR/AMP). Use GUIDE to display your audio amplifier’s program guide or setup menu. Use INFO to display the audio amplifier’s program information. ▲ ▲ Use SELECT to set the surround sound. Use ▲ (or ▼) to adjust the volume higher (or lower). Use (or ) to adjust the balance left (or right).
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 55 Use the transport keys to control your CD player (if applicable). Use SLEEP to activate your audio amplifer’s sleep timer (not available for all devices). After programming, press M1 ~ M3 once to run a desired macro (see Using Macros on page 34). After programming, press L1 ~ L4 once to activate a learned function. See Using Learning on page 29. Use to turn on or off the key backlight.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 56 KEY INDEX Audio Cassette Deck Functions (continued) Press MUTE once to turn the audio cassette deck’s audio off or on (if applicable). Use the keypad (1 ~ 9 and 0) to directly select tracks. If the original remote control required pressing an Enter key to select a track, also press the ENTER key after the track number (e.g., 1-2 -ENTER). Use TV/VID to switch the audio cassette deck between input and output.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 57 Audio Receiver Functions Press RCVR/AMP once to control your audio receiver. Press POWER once to turn on or off the selected device (e.g, RCVR/AMP). Use GUIDE to display your audio receiver’s program guide or setup menu. Use INFO to display the audio receiver’s program information. ▲ ▲ Use SELECT to set the surround sound. Use ▲ (or ▼) to adjust the volume higher (or lower). Use (or ) to adjust the balance left (or right).
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 58 KEY INDEX Audio Receiver Functions (continued) Use the transport keys to control your CD player (if applicable). Use SLEEP to activate your audio receiver’s sleep timer (not available for all devices). After programming, press M1 ~ M3 once to run a desired macro (see Using Macros on page 34). After programming, press L1 ~ L4 once to activate a learned function. See Using Learning on page 29. Use to turn on or off the key backlight.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 59 Use VOL+ (or VOL-) to raise (or lower) the audio turntable’s audio volume (if applicable). Press MUTE once to turn the audio turntable’s audio off or on (if applicable). Use the keypad (1 ~ 9 and 0) to directly select tracks. If the original remote control required pressing an Enter key to select a track, also press the ENTER key after the track number (e.g., 1-2 -ENTER). Use the transport keys to control your audio turntable (if applicable).
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 60 KEY INDEX (Continued) Cable Converter Functions Press CBL once to control your cable converter. Press POWER once to turn on or off the selected device (e.g, SAT). Press MENU once to display your cable converter’s main menu. Use GUIDE to display your cable converter’s program guide or setup menu. Use EXIT to exit from your cable converter’s guide or menu. Use INFO to display the cable converter’s current channel and program information.
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 61 Press ENTER once after entering the channel numbers on some TVs. Use TV/VID to switch the TV’s input to view TV or cable programs. Use the transport keys to control your cable converter’s VOD service (if applicable). Use SLEEP to activate your cable converter’s sleep timer (not available for all devices). After programming, press M1 ~ M3 once to run a desired macro (see Using Macros on page 34).
Producer 2002 IR Mnl 4/4/02 10:02 AM Page 62 KEY INDEX (continued) CD Player Functions Press CD once to control your CD player. Press POWER once to turn on or off the selected device (e.g, CD). Use GUIDE to display your CD player’s program guide. Use INFO to display the CD player’s current channel and program information. ▲ ▲ Use SELECT to select a compact disc. Use ▲ (or ▼) to select the next (or previous) CD. Use (or ) to select the next (or previous) track.
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 63 Use to turn on or off the key backlight. When this feature is activated, keys will remain backlit for 5 seconds after the last key press. In the setup mode, backlighting will remain on for 30 seconds. Use SET for all programming sequences. DVD Player Functions Press DVD once to control your DVD player. Press POWER once to turn on or off the selected device (e.g, DVD). Press MENU once to display your DVD player’s main menu.
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 64 KEY INDEX DVD Player Functions (continued) Use TV/VID to switch the TV’s input to view TV or DVD programs. Use the transport keys to control your DVD player. After programming, press M1 ~ M3 once to run a desired macro (see Using Macros on page 34). After programming, press L1 ~ L4 once to activate a learned function. See Using Learning on page 29. Use to turn on or off the key backlight.
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 65 Home Automation Functions Press AUX once to control home automation. See Re-assigning Device Keys on page 37. Press POWER once to turn on home automation. Use VOL+ (or VOL-) to brighten (or dim) the lights controlled by home automation. Press MUTE once to turn off home automation. Use CH+ (or CH-) to turn home automation on (or off). After programming, press M1 ~ M3 once to run a desired macro (see Using Macros on page 34).
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 66 KEY INDEX LD (Laser Disc) Player Functions Press AUX once to control home automation. See Re-assigning Device Keys on page 37. Press POWER once to turn on or off the selected device (e.g, AUX). Press MENU once to display your LD player’s main menu. Use GUIDE to display your LD player’s program guide. Use EXIT to exit from your LD player’s guide or menu. Use INFO to display the LD player’s current channel and program information.
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 67 After programming, press M1 ~ M3 once to run a desired macro (see Using Macros on page 34). After programming, press L1 ~ L4 once to activate a learned function. See Using Learning on page 29. Use to turn on or off the key backlight. When this feature is activated, keys will remain backlit for 5 seconds after the last key press. In the setup mode, backlighting will remain on for 30 seconds. Use SET for all programming sequences.
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 68 KEY INDEX Satellite Receiver Functions (continued) Use CH+ (or CH-) to select the satellite receiver’s next higher (or lower) channel. Press PREV once to recall the last-viewed channel and to page back one screen on the satellite receiver’s main menu. Use the keypad (1 ~ 9 and 0) to directly select channels (e.g., 009 or 031).
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 69 After programming, use COM SKIP to skip commercials on your satellite receiver. See Using Commercial Skip on page 48. Use to turn on or off the key backlight. When this feature is activated, keys will remain backlit for 5 seconds after the last key press. In the setup mode, backlighting will remain on for 30 seconds. Use SET for all programming sequences. TV Functions Press TV once to control your television.
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 70 KEY INDEX TV Functions (continued) Use CH+ (or CH-) to select the TV’s next higher (or lower) channel. Press PREV once to recall the last-viewed channel and to page back one screen on the TV’s main menu. Use the keypad (1 ~ 9 and 0) to directly select channels (e.g., 009 or 031). If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e.g., 0-3-1-ENTER).
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 71 After programming, use COM SKIP to skip commercials on your TV. See Using Commercial Skip on page 48. Use to turn on or off the key backlight. When this feature is activated, keys will remain backlit for 5 seconds after the last key press. In the setup mode, backlighting will remain on for 30 seconds. Use SET for all programming sequences. VCR Functions Press VCR once to control your VCR. Press POWER once to turn on or off the selected device (e.g, VCR).
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 72 KEY INDEX VCR Functions (continued) Press PREV once to recall the last-viewed channel and to page back one screen on the VCR’s main menu. Use the keypad (1 ~ 9 and 0) to directly select channels (e.g., 009 or 031). If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e.g., 0-3-1-ENTER). Press ENTER once after entering the channel numbers on some VCRs.
Use to turn on or off the key backlight. When this feature is activated, keys will remain backlit for 5 seconds after the last key press. In the setup mode, backlighting will remain on for 30 seconds. Use SET for all programming sequences. LIMITED WARRANTY One For All® warrants, to the original purchaser only, that this product will be free from defects in materials and workmanship, under normal use, for ninety (90) days from the date of original purchase.
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 74 CUSTOMER SUPPORT For assistance, please contact us in any of the following ways: • E-mail: ofasupport@ueic.com • Internet: http://www.oneforall.com • Consumer Help Line: (330) 405-8616 ADDITIONAL INFORMATION As you update your home entertainment system, One For All® has a universal remote control that will fit your needs. Look for these exciting products at a retailer near you. One For All Access 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 75
Producer 2002 IR Mnl 4/4/02 10:03 AM Page 76
