Dust Collector - Baldor Shown with optional bolt together Angle Iron stand and optional 55 gal. steel drum. *Models may vary sligthly in appearance. Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204 Phone 1-800-732-4065 315-476-5151 Fax 315-476-5044 www.oneida-air.
Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualified technicians and sales staff are available 7:30am - 6:00pm EST Mon. - Thur. and 7:30am - 5:00pm EST Fri. to answer any questions concerning OAS products and dust collection. Call for ductwork design and ductwork quotes, including system pricing and shipping cost. Read the entire Owners Manual before installing or operating system! Table of Contents Page I.
I. System Start-Up Information 1. Read the installation and maintenance instructions as well as the recommended safety practices in this manual. 2. Install Ductwork completely before operating collector: A.) Seal ductwork with silicone sealant or duct tape. B.) Have Dust Bin in place and sealed. 3. Have licensed electrician wire Fan / Blower according to wire diagram on pg. 13 in this owners manual. 4. Have licensed electrician check current draw on motor with all gates open.
II. Pro Series 2000 Configurations Caution: If exhaust air is vented outside you must provide make up / return air. Flue gases (carbon monoxide) can be drawn into the shop from furnaces, water heaters or other appliances. 1. External Cartridge Filter - Silencer Included with Filter Cartridge Filter Media 1 Pleated Spun-Bonded Cartridge Filter 62 / 130 Sq. Ft. Accredited, independent lab tested. Bathed in teflon-like coating for easy dust release. Captures 99.9% of Test Material from 0.2 - 2 microns.
III. General Specifications & Fan Performance Curves 1973 CFM @ 2 SP w/c w/o filter Full 16 gauge galvanized cyclone & 14 ga. barrel Rectangular inlet with included Square to Round to 8 Rectangular outlet Cast aluminum fan wheel back inclined non-sparking, non-ferrous dynamic, two-planed balanced to ISO 6.3 specifications. Sound 80 - 82dB @ 10 with Built-in Silencer and Filter 130 Sq. Ft. Filter Media / Spun-Bonded U.S. Made Baldor / TEFC / Class F / 1.
IV. Dimensions For Minimum Mounting Heights w/ 62 Filter. *Dimensions subject to slight variation in manufacturing. 53.00 27.00 18.00 8.00 8.00 100.00 18.00 81.00 62.00 72.00 60.00 Dimensions shown with 5" flex hose between drum and cone collars 35 Gal Shown Add 8" for 55 Gal 4.00 16.00 5 Pro 2000 Owners Manual c O.A.S.
V. General Assembly XXK200001 - 1 phase XXK200003 - 3 phase 15 & 15a (8) 5/16 Washers (8) 5/16 Nuts 1e 1f f7 1a 5 5a 2 5b 5c (8) 5/16 Washers (8) 5/16 Nuts 6 12 (7) 3/8 x 1 Bolts (7) 3/8 Washers (7) 3/8 Nuts Square to Round Connects to Inlet Cyclone Barrel 7 3 f7 11 4 5d Cone 0 1 2 3 4 5 INCHES W.C. 13b 14d 14 13e 14a 14c 14b Optional Angle Iron Stand 13b 13a 13c 30. Optional 55 gal. Angle Iron Stand Part # STG023055 1. Uprights - SXX000068 (4) 2.
VI. General Assembly Instructions There are essentially three ways to assemble your collector and to attach it to the bracket. The way that is right for you should be determined by expertise and manpower available. When the units are all assembled they are very heavy and top weighted. All of this should be taken into account before deciding on the method best suited for you. With all assemblies, make sure rectangular air outlet is oriented on Fan/Blower housing as you are looking down as in Fig.
VII. Bracket Assembly 1. You must determine the direction the fan outlet will point to proceed with this mounting assembly. The collector will seem quieter if the outlet is aimed away from the area people tend to work. Slots in the brackets are .406 x 1.00 Note: Bolts included to mount bracket to collector. Hardware NOT included to mount to wall. 1 16 2. Hold bracket against wall with top of plate at 60. Mark where mounting holes fall. Mount wall bracket.
VIII. Filter Assembly External 62 Filter Assembly *Silencer Included. 1. Attach cartridge with hardware provided making sure gasket is attached. See Fig. 1 2. If Filter requires additional support. Use the plate at the top of the filter to support the filter assembly. Note: If filter cartridge is located away from the cyclone and motor, additional square-to-round connectors and pipe can be purchased. Fig.
IX. Filter Maintenance External Filter Cartridge Cleaning Intervals When unit is turned off, use compressed air to blow dust off from exterior of filter. Hold nozzle at least 8 away from filter pleats*. Do not remove bottom dust pan before or during the blow-off process! Let dust settle into dust pan. Unclip and dump out dust. Filter removal is not required. * WARNING: A close, direct blast with the compressed air nozzle too close to filter, may damage filter media.
X. Filter Efficiency Gauge Mounting Instructions Elbow Plenum (Side View) Air Flow to Filter 0 1 2 3 4 5 INCHES W.C. Mounting Instructions 1. Mount brass static pressure tube in plenum with tip pointed into the air stream. Use mounting bracket and sheet metal screws if interior of plenum is not accessible. Refer to drawings for location of brass static pressure tube. 2. Refer to instructions provided with gauge for mounting to bracket. 3.
XI. Directions for Cleaning External Filter All steps should be done with a dust mask and eye protection. The External Filter can be cleaned using the following methods: 1. Compressed air from outside. Blast air along pleats of the filter at about a 20 angle. Blast air out and away from you or anyone in the general area. Keep air nozzle at least 6 from filter. Closer blasts may damage filter material. 6 Filter must be cleaned regularly or filter damage may result.
XII. Wiring Instructions for Magnetic Starter Always use a licensed, professional electrician. Follow Wiring Diagram on Motor. Note: This Dust Collector is pre-wired at the factory and need only be plugged into a NEMA 6020R dedicated electrical receptacle. 5hp single phase only. 13 Pro 2000 Owners Manual c O.A.S.
XIII. Troubleshooting Unplug unit before servicing or cleaning. 13 14 Pro 2000 Owners Manual c O.A.S.
XIV. Fire Hazards - Read Before Installing and Operating Oneida Collectors are designed for WOOD DUST only!! Wood shaping and cutting processes generate wood chips, shavings, and dust. These materials are considered combustible. Air borne wood dust below 420 microns in size (.017 of an inch) in certain concentration ranges when ignited can deflagrate (burn quickly).
XV. Terms and Conditions Checking in Order Please look over the shipped order very carefully in the presence of the delivery person for damage or incomplete shipment before signing the delivery receipt. Please note any tears or irregularities in shipping packaging, however slight, on the shipping delivery receipt. This could be an indication of extensive concealed damage. The shipping company will not take responsibility if the damage is not noted on the delivery receipt.
XVI. Stand Assembly - STG023055 23 7/8 T F LE 23 7/8 23 7/8 (32) 5/16 Bolts (32) 5/16 Nuts (64) 5/16 Flat Washers 23 7/8 23 7/8 T H RIG 23 7/8 68 FRO lowe NT has r bra n ce a o cros s. 23 7/8 Washer Nut Bolt Stand 17 Pro 2000 Owners Manual c O.A.S.
XVII. Accessories Bolt Together Angle Iron Stand STG023055 - 55 gal. Stand Replacement Filter FCS186200 18 x 62 / 130 Sq. Ft. Spun-Bonded. Filters 99.9% of test material from 0.2 to 2 microns. Dust Containers 35 gal. Fiber 55 gal. Fiber 55 gal. Steel The BAG Gripper ABX000000 The BAG Gripper provides the ability to use convenient plastic bags inside your dust drum.
XVIII. Fan Motor Maintenance Per Baldor specifications, their 2 pole motors (3600 RPM) motors are to be relubricated every 5500 hours. Table 1 - Service Conditions Table 2 - Lubrication Interval Multiplier Per Baldor specifications, add .30 ounces (8.4 grams) of Mobil Polyrex grease by weight or .6 cubic inches (2 teaspoons) of Mobil Polyrex grease by volume. 19 Pro 2000 Owners Manual c O.A.S.
XVIV. Remote Wiring Diagram Retrofit (Wiring) of Wireless Remote into 220V Control Circuit of Square D / Telemecanique Mag Starters Square D Telemecanique Mag Starters AMK Series 1A Plug into 9 pin female Molex on back panel of starter base. 3 Wire Adaptor Molex AMA000000 Important! Remove this factory installed Jumper Wire.
