™ OneSpace is a Trademark of Comfort Products, Inc. ASSEMBLY INSTRUCTIONS MODEL 50-61201 SUPPLIER CODE: PMEX 6 Cube Organizer, White CUSTOMER SERVICE For fastest service on claims, requests for replacement parts, or questions, please visit our website at www.comfortproducts.net/support e-mail: customerservice@comfortproducts.net Keep your sales receipt as documentation of your ownership.
Top maximum weight capacity =40lbs 9 3 7 5 2 8 6 1 7 4 2 OF 11 Shelf maximum weight capacity =10lbs
DESCRIPTION PART STOCK NO QTY PART DESCRIPTION STOCK NO QTY 1 Side Panel Left 51-61201A 1 6 Lower Shelf Panel 51-61201F 1 2 Side Panel Right 51-61201B 1 7 Center Panel Top and Bottom 51-61201G 2 3 Top Panel 51-61201C 1 8 Center Panel Middle 51-61201H 1 4 Bottom Panel 51-61201D 1 9 Back Panel 51-61201J 3 5 Upper Shelf Panel 51-61201E 1 HARDWARE KIT STOCK # 51-61201KIT DESCRIPTION PART A QTY 18 B Cam 18 C Wood Dowel (6 x 30mm) 14 D CSK Screw (M4.
NOTE: Many of the boards are similar in appearance. Pay close attention to the differences between the boards as well as to the placement of the bolts. & Lower Shelf Panel (6), Center Panel Top and Bottom (7) and Center Panel Middle (8). Part # C x 14 7 7 1 5 2 8 6 Top Panel (3), Upper Shelf Panel (5) and Lower Shelf Panel (6).
Use two CSK Screws (D) to attach the Upper Shelf Panel (5) and Center Panel Top (7). Make sure that the grooves for the Back Panel are aligned. Also, make sure that the bolts are facing out and all the grooves are at the bottom as shown below. Part # D x 2pcs 7 Bolts facing out 5 to the Upper Shelf Panel (5), making sure that the grooves for the Back Panel are aligned.
With a screwdriver tighten two CSK Screws (D) to attach the Lower Shelf Panel (6) to Center Panel Middle (8). Make sure that the grooves for the Back Panel are aligned. Part # D x 2pcs 7 8 5 6 to Lower Shelf Panel (6). While doing this make sure that the grooves for the Back Panel are aligned.
Step 7: Slide in one Back Panel (9) with the finished side facing inside the cube. Note that the panels are not square. The long side should meet with the groove of Center Panel Middle (8). 7 8 5 6 7 9 Step 8: NOTE: When attaching a side panel as shown below, you may need to push on the back panel to align it with the groove in the side panel. Insert the Cams (B) into the Upper Shelf Panel (5) and Lower Shelf Panel (6).
Step 9: clockwise and then cover them with Cam Caps (E). Part # B x 4pcs Part # E x 4pcs 5 7 8 6 2 7 1 Step 10: Slide in one Back Panel (9) with the finished side facing inside the cube. Note the orientation of the long and short sides in the drawing below.
Step 11: Use six CSK Screws (D) to attach the Bottom Panel (4) to Side panel Left (1), Side panel Right (2) and Center Panel Bottom (7). Make sure that the groove in the Bottom Panel (4) is aligned with the Back Panel (9). Part # D x 6pcs 7 5 8 6 1 2 7 4 9 Step 12: Note the orientation of the sides in the drawing.
Step 13: Attach the Top Panel (3) to the Side Panel Left (1), Side Panel Right (2) and Center Panel Top (7). While clockwise and then cover them with Cam Caps (E).
• • • • DO NOT stand on the desk. Do not use the desk as a stepladder. ed. Every 6 months, check all bolts and screws to ensure they are tight. This product is California 93120 Compliant for Formaldehyde. PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year.