™ OneSpace is a Trademark of Comfort Products, Inc. ASSEMBLY INSTRUCTIONS MODEL # 50-LD0101 SUPPLIER CODE: LDCZ Essential Computer Desk, White CUSTOMER SERVICE For fastest service on claims, requests for replacment parts, or questions, please visit our website at: www.comfortproducts.net/support e-mail: customerservice@comfortproducts.net Keep your sales receipt as documentation of your ownership.
ASSEMBLY OVERVIEW Hutch maximum weight capacity = 22lbs Desktop maximum weight capacity = 165lbs Middle shelf maximum weight capacity = 22lbs Bottom shelf maximum weight capacity = 44lbs Drawer maximum weight capacity = 11lbs 2 of 16
# .
PARTS LIST 2 OF 2 ITEMS ARE NOT SHOWN TO SCALE.
HARDWARE LIST EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE. HARDWARE KIT STOCK # 51-LD0101HA PART DESCRIPTION QTY. A M4 X 40MM 10 B M4 X 18MM 2 C M4 X 14MM 16 D - READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING. - REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION. - OPEN THE HARDWARE AS NEEDED . - ASSEMBLE IN AN AREA WITH PLENTY OF SPACE. - READ EACH STEP BEFORE BEGINNING CONSTRUCTION. - NEVER FORCE THE SCREWS OR FITTINGS. - KEEP THIS MANUAL FOR FUTURE REFERENCE.
ASSEMBLY INSTRUCTIONS STEP 1 Use a hammer to attach foot pins (G) to the bottom of the left (2), middle (4), and right (3) boards.
ASSEMBLY INSTRUCTIONS STEP 2 Attach a left outer drawer roller (21a) to the left board (2) and a right outer drawer roller (21a) to the right board (3) using small screws (C). Attach two rollers to the middle board (4), a right outer roller (21a) to the left side and a left outer roller (21a) to the right side. Refer to drawing below for which holes in the roller to use.
ASSEMBLY INSTRUCTIONS STEP 3 screw Do not overtighten bolts or cams will not lock properly.
ASSEMBLY INSTRUCTIONS STEP 4 D Insert cams (E) into the bottom shelf (9) and into the two support boards (10). Make sure the arrows are facing the smaller holes which the bolts go into. First, attach shelf and support boards to the middle board (4), and then attach these to the right board (3) by aligning the bolts and cams. With a screwdriver turn the cams about 1/2 turn clockwise to lock into place. CAUTION: Do not overtighten cams. E CAUTION: Do not over tighten cams.
ASSEMBLY INSTRUCTIONS STEP 6 Insert four cams (E) into the left back board (5). Make sure arrows are facing the smaller holes. Attach back board (5) to left board (2) and middle board (4). Turn the cams about 1/2 turn clockwise to lock into place. CAUTION: Do not overtighten cams. CAUTION: Make sure these holes are facing up. Ex4 E STEP 7 Screw minifix bolts (D) into hutch top (17), hutch left board (18), and hutch right board (19).
ASSEMBLY INSTRUCTIONS STEP 8 Insert two cams into the hutch back board (16) and attach to the hutch top board (17). Insert ten cams into the hutch back (16), hutch top (17), and hutch middle board (20). Attach hutch left (18), hutch middle (20), and hutch right (19) to the back and top boards. 19 E x 12 E 16 17 20 16 17 18 STEP 9 Screw eight minifix bolts (D) into desktop (1). Attach hutch to desktop using six screws (A) as shown.
ASSEMBLY INSTRUCTIONS STEP 10 Insert eight cams (E) into the left, middle, and right boards and left back board as shown. Attach desktop (1) with hutch to the lower part of the desk by aligning the eight bolts (D) (already screwed into the desktop) with cams. Tighten cams 1/2 turn.
ASSEMBLY INSTRUCTIONS STEP 12 STEP 11 Insert cams into the left (12) and right (13) drawer boards and attach both boards to the drawer front (11). Make sure the grooves for the drawer bottom are aligned. Dx4 Ex4 13 12 11 11 STEP 13 STEP 14 Insert drawer bottom (15) into grooves. Align groove in drawer back (14) with drawer bottom. Attach drawer back (14) to left and right drawer boards using four screws (A).
ASSEMBLY INSTRUCTIONS STEP 15 STEP 16 Attach drawer handle (F) to drawer front using two screws (B). Attach two inner drawer rollers (21b), one left and one right, to the bottom of drawer using four screws (C) as shown. Make sure rollers are oriented to the back of the drawer. Refer to drawing below for which holes in the roller to use.
ASSEMBLY INSTRUCTIONS STEP 18 Insert shelf supports (H) into any of the four sets of holes, according to desired height. Place middle shelf (8) on supports. Hx4 STEP 19 STEP 20 Align inner and outer rollers to insert drawer and keyboard tray. Place plastic caps (22) over cams at the back of the desk and cams in the hutch middle board (20).
• • • • DO NOT stand on the desk. Do not use the desk as a stepladder. ed. Every 6 months, check all bolts and screws to ensure they are tight. This product is California 93120 Compliant for Formaldehyde. PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year.