HT-S5200_En.book 1 ページ 2009年3月9日 月曜日 午後4時31分 Contents Introduction ...................................2 7.1ch Home Theater System Connections ................................18 HT-S5200 AV Receiver (HT-R570) Speaker Package (HTP-570) Front Speakers (SKF-570 L/R) Center Speaker (SKC-570) Surround Speakers (SKR-570 L/R) Surround Back Speakers (SKB-570 L/R) Subwoofer (SKW-570) Dock for iPod (UP-A1L) Instruction Manual Turning On & First Time Setup .....38 Basic Operations.........................
HT-S5200_En.book 2 ページ 2009年3月9日 月曜日 午後4時31分 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
HT-S5200_En.book 3 ページ 2009年3月9日 月曜日 午後4時31分 Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water.
HT-S5200_En.book 4 ページ 2009年3月9日 月曜日 午後4時31分 Speaker Precautions Package Contents Placement Make sure you have the following accessories: • The subwoofer cabinet is made out of wood and is therefore sensitive to extreme temperatures and humidity, do not put it in locations subject to direct sunlight or in humid places, such as near an air conditioner, humidifier, bathroom, or kitchen. • Do not put water or other liquids close to the speakers.
HT-S5200_En.book 5 ページ 2009年3月9日 月曜日 午後4時31分 Package Contents—Continued Speaker Package HTP-570 4 rubber spacers for center speaker Front speakers (SKF-570 L/R) Dock for iPod UP-A1L Center speaker (SKC-570) Surround speakers (SKR-570 L/R) * In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operation are the same regardless of color.
HT-S5200_En.book 6 ページ 2009年3月9日 月曜日 午後4時31分 Using Two Sets of Speakers Speaker Sets A and B You can use two sets of speakers with the AV receiver: speaker set A and speaker set B. Speaker set A should be used in your main listening room for up to 7.1-channel playback. * While speaker set B is on, speaker set A is reduced to 5.1-channel playback. Speaker set B can be used in another room and offers 2-channel stereo playback. * Only analog input sources are output by speaker set B.
HT-S5200_En.book 7 ページ 2009年3月9日 月曜日 午後4時31分 Features AV Receiver HT-R570 Amplifier • • • • • • 75 Watts/Channel @ 8 ohms (FTC) 130 Watts/Channel @ 6 ohms (IEC) WRAT-Wide Range Amplifier Technology High-Current Low-Impedance Drive Optimum Gain Volume Circuitry H.C.P.S.
HT-S5200_En.book 8 ページ 2009年3月9日 月曜日 午後4時31分 Features—Continued *3 Music Optimizer™ is a trademark of Onkyo Corporation. *4 HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. *5 SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All other marks and logos are the property of their respective owners. All rights reserved. SIRIUS subscription sold separately.
HT-S5200_En.book 9 ページ 2009年3月9日 月曜日 午後4時31分 Contents Introduction Basic Operations Important Safety Instructions .................................... 2 Precautions ............................................................... 3 Speaker Precautions................................................. 4 Package Contents..................................................... 4 AV receiver HT-R570 ............................................ 4 Speaker Package HTP-570...................................
HT-S5200_En.book 10 ページ 2009年3月9日 月曜日 午後4時31分 Front & Rear Panels Front Panel a b c d e f g h i j k l mn o p r s t q u v The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item. a ON/STANDBY button (38) Sets the AV receiver to On or Standby.
HT-S5200_En.book 11 ページ 2009年3月9日 月曜日 午後4時31分 Front & Rear Panels—Continued For detailed information, see the pages in parentheses. p RETURN button Selects the previously displayed setup menu. q MASTER VOLUME control (44) Sets the volume of the AV receiver to Min, 1 through 79, or Max. r PHONES jack (46) This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening. s MUSIC OPTIMIZER button (47, 77) Turns the Music Optimizer on or off.
HT-S5200_En.book 12 ページ 2009年3月9日 月曜日 午後4時31分 Front & Rear Panels—Continued Rear Panel a b jk c d l m e f g h n o p q r a DIGITAL IN COAXIAL 1 and 2 These coaxial digital audio inputs are for connecting components with a coaxial digital audio output, such as a CD player or DVD/BD player. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 42.
HT-S5200_En.book 13 ページ 2009年3月9日 月曜日 午後4時31分 Front & Rear Panels—Continued n CBL/SAT IN A cable or satellite receiver can be connected here. There is composite video input jacks for connecting the video signal, and there are analog audio input jacks for connecting the audio signal. o VCR/DVR IN/OUT A video component, such as a VCR or DVR, can be connected here for recording and playback.
HT-S5200_En.book 14 ページ 2009年3月9日 月曜日 午後4時31分 Speaker Package Subwoofer (SKW-570) For detailed information, see the pages in parentheses. ■ Front a STANDBY/ON indicator Red: Subwoofer in standby mode Blue: Subwoofer on With the Auto Standby function, the SKW-570 automatically turns on when an input signal is detected in Standby mode. When there’s no input signal for a while, the SKW-570 automatically enters Standby mode.
HT-S5200_En.book 15 ページ 2009年3月9日 月曜日 午後4時31分 Speaker Package—Continued Front, Center, Surround, Surround Back speakers (SKF-570, SKC-570, SKR-570, SKB-570) ■ Rear SKF-570 SKR-570/SKB-570 a a b b SKC-570 a b a Keyhole slots These keyhole slots can be used to wall-mount the speaker. See page 21 for mounting instructions. b Speaker terminals These push terminals are for connecting the speaker to the HT-R570 with the supplied speaker cables.
HT-S5200_En.book 16 ページ 2009年3月9日 月曜日 午後4時31分 Remote Controller Controlling the AV receiver To control the AV receiver, press the [RECEIVER] button to select Receiver mode. You can also use the remote controller to control your DVD/BD player, CD player, and other components. See page 78 for more details. d Arrow [q]/[w]/[e]/[r] and ENTER buttons Used to select and adjust settings. e SETUP button Used to change settings. f LISTENING MODE buttons (64) Used to select the listening modes.
HT-S5200_En.book 17 ページ 2009年3月9日 月曜日 午後4時31分 Remote Controller—Continued Installing the Batteries 1 To open the battery compartment, press the small lever and remove the cover. Aiming the Remote Controller When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below. Remote control sensor STANDBY indicator AV receiver 30° 2 3 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment.
HT-S5200_En.book 18 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver Enjoying Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring Dolby Digital or DTS. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes. Front left and right speakers (SKF-570) These output the main sound.
HT-S5200_En.book 19 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Speaker Configuration Speaker Connection Precautions For 7.1-channel surround-sound playback, you need seven speakers and a powered subwoofer. The following table shows which channels you should use based on the number of speakers you have. Read the following before connecting your speakers: • You can connect speakers with an impedance of between 6 and 16 ohms.
HT-S5200_En.book 20 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting Speaker Set A Connecting Speaker Set B 1 Strip 1/2"-5/8" (12-15 1/2"-5/8"(12-15mm) mm) of insulation from the ends of the speaker cables. (Supplied speaker cables are already stripped.) 1 Strip 3/8"-1/2" (10-12 3/8"-1/2"(10-12mm) mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. 2 Unscrew the terminal.
HT-S5200_En.book 21 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Wall Mounting The speakers can easily be wall mounted by using the keyhole slots. To mount the front or surround speakers vertically, use the keyhole slot shown to hang each speaker on a screw that’s securely screwed into the wall. Front speakers (SKF-570) Keyhole slot for wall mounting Leave a gap of between 7/32" (5 mm) and 3/8" (10 mm) between the wall and the base of the screw head, as shown.
HT-S5200_En.book 22 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting the AM Loop Antenna Connecting Antenna This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. The supplied indoor AM loop antenna is for indoor use only.
HT-S5200_En.book 23 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting an Outdoor FM Antenna Connecting an Outdoor AM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
HT-S5200_En.book 24 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued AV Connection Color Coding About AV Connections RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.
HT-S5200_En.book 25 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting Audio and Video Signals to the AV receiver By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver. : Signal Flow Video Video Audio Audio TV, projector, etc. DVD/BD player, etc.
HT-S5200_En.book 26 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting Components with HDMI About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD/BD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
HT-S5200_En.book 27 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Making HDMI Connections If you have an HDMI-compatible player, you can connect it to the AV receiver with an HDMI cable. Step 1: Connect your HDMI-compatible TV to the AV receiver’s HDMI OUT jack. Step 2: Connect your HDMI-compatible player to the AV receiver’s HDMI IN 1, 2, or 3 jack. Step 3: Connect your HDMI-compatible player to an analog and/or digital audio input on the AV receiver.
HT-S5200_En.book 28 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a TV or Projector Step 1: Video Connection Choose a video connection that matches your TV ( A or B ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from your TV. • To enjoy Dolby Digital and DTS, use connection b or c .
HT-S5200_En.book 29 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a DVD/BD player Step 1: Video Connection Choose a video connection that matches your DVD/BD player ( A or B ), and then make the connection. You must connect the AV receiver to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD/BD player ( a , b , or c ), and then make the connection.
HT-S5200_En.book 30 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a VCR or DVR for Playback Hint! With this hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Step 1: Video Connection Choose a video connection that matches your VCR or DVR ( A or B ), and then make the connection. You must connect the AV receiver to your TV with the same type of connection.
HT-S5200_En.book 31 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a VCR or DVR for Recording Step 1: Video Connection Make the video connection A . Step 2: Audio Connection Make the audio connection a . Connection AV receiver Signal flow VCR or DVD recorder A VCR/DVR OUT V ⇒ Composite video input a VCR/DVR OUT L/R ⇒ Audio L/R input a C A L VIDEO IN R AUDIO IN VCR or DVR Notes: • The AV receiver must be turned on for recording.
HT-S5200_En.book 32 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source Hint! With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Step 1: Video Connection Choose a video connection that matches the video source ( A or B ), and then make the connection.
HT-S5200_En.book 33 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a Camcorder, Game Console, or Other Device Step 1: Make the video connection A . Step 2: Make the audio connection a . a AUX INPUT L AUDIO R L AUDIO R OUT Camcorder, game console, etc.
HT-S5200_En.book 34 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a CD Player or Turntable ■ CD Player or Turntable (MM) with Built-in Phono Preamp Step 1: Choose a connection that matches your CD player ( a , b , or c ). Use connection a for a turntable with a built-in phono preamp.
HT-S5200_En.book 35 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches your recorder ( a , b , or c ), and then make the connection. c IN OPTICAL a L 2 (CD) R TV/TAPE COAXIAL a (DVD/BD) L b R TV/TAPE Connect one or the other These connections must be assigned (see page 42) L OPTICAL OUT COAXIAL OUT R L AUDIO IN R AUDIO OUT Cassette, CDR, MD, etc.
HT-S5200_En.book 36 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting an RI Dock Not all iPod models output video. For information about which iPod models are supported by the RI Dock, see the RI Dock’s instruction manual. ■ If Your iPod Doesn’t Support Video: Connect your RI Dock’s audio output jacks to the AV receiver’s TV/TAPE IN L/R jacks.
HT-S5200_En.book 37 ページ 2009年3月9日 月曜日 午後4時31分 Connecting the AV receiver—Continued Connecting Onkyo u Components Step 1: Make sure that each Onkyo component is connected to the AV receiver with an analog audio cable (RCA). Step 2: Make the necessary u connections (see illustration below). Step 3: If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 43).
HT-S5200_En.book 38 ページ 2009年3月9日 月曜日 午後4時31分 Turning On the AV receiver ON/STANDBY STANDBY indicator ON/STANDBY RECEIVER Turning On and Standby AV receiver Remote controller or On the AV receiver, press the [ON/STANDBY] button. On the remote controller, press the [RECEIVER] button, followed by the [ON/STANDBY] button. The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
HT-S5200_En.book 39 ページ 2009年3月9日 月曜日 午後4時31分 First Time Setup This section explains the settings that you need to make before using the AV receiver for the very first time. Audyssey 2EQ™ Room Correction and Speaker Setup With the supplied calibrated microphone, Audyssey 2EQ automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position.
HT-S5200_En.book 40 ページ 2009年3月9日 月曜日 午後4時31分 First Time Setup—Continued Using Audyssey 2EQ™ Notes: • If the AV receiver is muted, it will be unmuted automatically when the Audyssey 2EQ Room Correction and Speaker Setup starts. • Room correction and speaker setup cannot be performed while a pair of headphones is connected. • It takes about 10 minutes to complete the room correction and speaker setup for three positions. Total measurement time varies depending on the number of speakers.
HT-S5200_En.book 41 ページ 2009年3月9日 月曜日 午後4時31分 First Time Setup—Continued 5 When the following display appears, move the speaker setup microphone to measurement point c (page 39), and then press [ENTER]. Audyssey 2EQ™ performs more measurements. This takes a few minutes. When the measurements are complete, the results are calculated and saved automatically. 6 When the room correction and speaker setup is complete, disconnect the speaker setup microphone.
HT-S5200_En.book 42 ページ 2009年3月9日 月曜日 午後4時31分 First Time Setup—Continued Component Video Input Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector. For example, if you connect your DVD/BD player to COMPONENT VIDEO IN 2, you should assign it to the DVD/BD input selector. Digital Input Setup To enjoy Dolby Digital and DTS, you must connect your DVD/BD player to the AV receiver by using a digital audio connection (coaxial or optical). Here are the default assignments.
HT-S5200_En.book 43 ページ 2009年3月9日 月曜日 午後4時31分 First Time Setup—Continued 2 CBL/SAT TV/TAPE Use the Up and Down [q]/[w] buttons to select “2.Digital Audio”, and then press [ENTER]. VCR/DVR 1 4 Use the Up and Down [q]/[w] buttons to select an input selector, and then use the Left and Right [e]/[r] buttons to select: COAX1: Select if the component is connected to DIGITAL IN COAXIAL 1. COAX2: Select if the component is connected to DIGITAL IN COAXIAL 2.
HT-S5200_En.book 44 ページ 2009年3月9日 月曜日 午後4時31分 Basic Operations Basic AV receiver Operation SPEAKERS A/B MASTER VOLUME INPUT SELECTOR Subwoofer’s rear panel RECEIVER VOL MIN MAX OUTPUT LEVEL control OUTPUT LEVEL Input selector 1 AV receiver Remote controller 2 AV receiver Remote controller Use the AV receiver’s input selector buttons to select an input source. To select an input source with the remote controller. Press the [RECEIVER] button, and then press its INPUT SELECTOR buttons.
HT-S5200_En.book 45 ページ 2009年3月9日 月曜日 午後4時31分 Basic Operations—Continued This section explains functions that can be used with any input source. Muting the AV receiver You can temporarily mute the output of the AV receiver. Press [RECEIVER] first MUTING Press the [RECEIVER] button, and then press the remote controller’s [MUTING] button. The output is muted and the MUTING indicator flashes on the display.
HT-S5200_En.book 46 ページ 2009年3月9日 月曜日 午後4時31分 Basic Operations—Continued 7Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver’s PHONES jack. Displaying Source Information You can display various information about the current input source as follows. Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information.
HT-S5200_En.book 47 ページ 2009年3月9日 月曜日 午後4時31分 Basic Operations—Continued Using the Music Optimizer The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that use “lossy” compression, such as MP3. • If the beginnings of tracks from a PCM source are cut off, try the PCM setting. • If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. • The setting is stored individually for each input selector.
HT-S5200_En.book 48 ページ 2009年3月9日 月曜日 午後4時31分 Listening to the Radio AM/FM Frequency Step Setup 4 Use the Left and Right [e]/[r] buttons to select: 200k/10k: Select if 200k/10k steps are used in your area. 50k/9k: Select if 50k/9k steps are used in your area. 5 Press the [SETUP] button. Setup closes. RECEIVER qwer ENTER SETUP For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted.
HT-S5200_En.book 49 ページ 2009年3月9日 月曜日 午後4時31分 Listening to the Radio—Continued ■ Manual Tuning Mode Listening to AM/FM Stations TUNER TUNING TUNING MODE With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection. Use the [TUNER] input selector button to select “AM” or “FM”. In this example, FM has been selected. Band 1 Press the [TUNING MODE] button so that the AUTO indicator disappears from the display.
HT-S5200_En.book 50 ページ 2009年3月9日 月曜日 午後4時31分 Listening to the Radio—Continued ■ Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. Displaying AM/FM Radio Information DISPLAY TUNER Press the [DISPLAY] button to display the available information. Band Frequency Number buttons D.TUN Listening mode 1 Press the [TUNER] button repeatedly to select “AM” or “FM”, followed by the [D.TUN] button. (Actual display depends on country.
HT-S5200_En.book 51 ページ 2009年3月9日 月曜日 午後4時31分 Listening to the Radio—Continued Presetting AM/FM Stations MEMORY Selecting Presets ePRESETr ePRESETr You can store a combination of up to 40 of your favorite AM and FM radio stations. 1 Tune into the AM or FM station you want to store as a preset. 2 Press the [MEMORY] button. The preset number flashes. 3 While the preset number is flashing (about 8 seconds), use the PRESET [e]/[r] buttons to select a preset from 1 through 40.
HT-S5200_En.book 52 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio Listening to Sattellite Radio Indoor/outdoor antenna with 21-foot cable To listen to Satellite Radio, you’ll need to connect a SIRIUS Satellite Radio tuner (sold separately) to your Sirius-Ready receiver. SIRIUS Satellite Radio is available to residents of the US (except Alaska and Hawaii) and Canada.
HT-S5200_En.book 53 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio—Continued 4 TUNER Press the [SETUP] button. Remote controller Selecting SIRIUS Satellite Radio 1 AV receiver TUNER RECEIVER ENTER Remote controller / / / SETUP Setting the Satellite Radio Mode 1 Remote controller Press the [RECEIVER] button, followed by the [SETUP] button. On the AV receiver, press the [TUNER] INPUT SELECTOR button repeatedly to select SIRIUS.
HT-S5200_En.book 54 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio—Continued 3 Remote controller Use the Up and Down [q]/[w] buttons to select “Sirius ID”. Your SIRIUS Satellite Radio ID number is displayed. Write it below. ID: Selecting SIRIUS Satellite Radio Channels There are three ways to select SIRIUS Satellite Radio channels: • Channel Search mode: select any channel. • Category Search mode: select channels by category. • Direct tuning: enter channel number.
HT-S5200_En.book 55 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio—Continued Category Search Mode 1 AV receiver Remote controller TUNING , TUNING MODE Press the [TUNER] button, and then press the [ENTER] button repeatedly to select Category Search mode. MEMORY This procedure can also be performed on the AV receiver by using its [TUNER] button, and [TUNING MODE] button.
HT-S5200_En.book 56 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio—Continued Notes: • If you select an unavailable channel, “INVALID CHANNEL” appears on the display. • If you select a channel that you are not subscribed to, “CALL SIRIUS” appears on the display. • Channels that are locked must be unlocked before you can listen to them. See “Parental Lock” on page 58 for more information.
HT-S5200_En.book 57 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio—Continued ■ Deleting Presets 1 2 Select the preset that you want to delete. See the previous section. AV receiver While holding down the [MEMORY] button, press the [TUNING MODE] button. The preset is deleted and its number disappears from the display. Displaying SIRIUS Satellite Radio Information Press the [DISPLAY] button repeatedly to cycle through the available information.
HT-S5200_En.book 58 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio—Continued 2 2 Use the Up and Down [q]/[w] buttons to select “9. Antenna Aim,” and then press [ENTER]. Note: If the “SATRadio” is set to “None” (see page 53), the “Antenna Aim” item is not available. Use the Up and Down [q]/[w] buttons to select “10. Parental Lock”, and then press [ENTER]. “Enter : <0>” appears on the display.
HT-S5200_En.book 59 ページ 2009年3月9日 月曜日 午後4時31分 Listening to SIRIUS Satellite Radio—Continued 4 Use the number buttons to enter the old PIN number. If you enter the wrong PIN number, “Wrong Code!” appears on the display. You’ll be returned to step 2, and will need to start again. “New : <0>” appears on the display. 5 Use the number buttons to enter the new PIN number. “Confirm: <0>” appears on the display. 6 Enter the new PIN number again.
HT-S5200_En.book 60 ページ 2009年3月9日 月曜日 午後4時31分 UP-A1L Dock for iPod About the UP-A1L Dock With the supplied UP-A1L Dock, you can easily play the music, photo, or movie stored on your Apple iPod through the AV receiver and enjoy great sound. You can use the AV receiver’s remote controller to operate your iPod. For the latest information on the Dock, see the Onkyo Web site at: www.onkyo.com ■ Adjusting the iPod Adapter The iPod adapter needs to be adjusted to match your particular iPod.
HT-S5200_En.book 61 ページ 2009年3月9日 月曜日 午後4時31分 UP-A1L Dock for iPod—Continued Operating Notes: • Before selecting a different input source, stop iPod playback to prevent the AV receiver from selecting the iPod input source by mistake. • If any accessories are connected to your iPod, the AV receiver may not be able to select the input source properly. • While your iPod is in the Dock, its volume control has no effect.
HT-S5200_En.book 62 ページ 2009年3月9日 月曜日 午後4時31分 UP-A1L Dock for iPod—Continued f MUTING button (45) Mutes or unmutes the AV receiver. g ALBUM +/– button Selects the next or previous album. h VOL [q]/[w] button (44) Adjusts the volume of the AV receiver. i PLAYLIST [e]/[r] buttons Selects the previous or next playlist on the iPod. j RETURN button Exits the menu or returns to the previous menu. k Play [1] button Starts playback. If the component is off, it will turn on automatically.
HT-S5200_En.book 63 ページ 2009年3月9日 月曜日 午後4時31分 Recording This section explains how to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. • Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded. • DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.
HT-S5200_En.book 64 ページ 2009年3月9日 月曜日 午後4時31分 Using the Listening Modes Selecting the Listening Modes Selecting with the Remote Controller For a description of each listening mode, see “About the Listening Modes” on page 68. • The Dolby Digital and DTS listening modes can only be selected if your DVD/BD player is connected to the AV receiver with a digital audio connection (OPTICAL, or COAXIAL). • The listening modes you can select depends on the format of the input signal.
HT-S5200_En.book 65 ページ 2009年3月9日 月曜日 午後4時31分 Using the Listening Modes—Continued Listening Modes Available for Each Source Format The Speaker layout illustration shows which speakers are set to active in the “Sp Config” setting (see page 70). Front L Speaker The LISTENING MODE button illustration shows that listening modes can be selected.
HT-S5200_En.
HT-S5200_En.book 67 ページ 2009年3月9日 月曜日 午後4時31分 Using the Listening Modes—Continued 5.
HT-S5200_En.book 68 ページ 2009年3月9日 月曜日 午後4時31分 Using the Listening Modes—Continued About the Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing highfidelity reproduction. All of the source’s audio channels are output as they are.
HT-S5200_En.book 69 ページ 2009年3月9日 月曜日 午後4時31分 Using the Listening Modes—Continued Onkyo Original DSP Modes Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall. Unplugged Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.
HT-S5200_En.book 70 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup Common Procedures in Setup Menu Remote indicator RECEIVER qwer ENTER 1 Press the [RECEIVER] button followed by the [SETUP] button. 2 Use the Up and Down [q]/[w] buttons to select the function, and then press the [ENTER] button. 3 Use the Up and Down [q]/[w] button to select item, and then use the Left and Right [e]/[r] buttons to set them. 4 When you’ve finished, press the [SETUP] button. Setup closes.
HT-S5200_En.book 71 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup—Continued SurrBack*3*4 Small: Select if the surround back speakers are small (default). Large: Select if the surround back speakers are large. None: Select if no surround back speakers are connected. SurrBack Ch*5 2ch: Select if two (left and right) surround back speakers are connected. 1ch: Select if only one surround back L speaker is connected. *3 If the “Surround” setting is set to “None”, this setting does not appear.
HT-S5200_En.book 72 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup—Continued Unit feet: Distances can be set in feet. Range: 1 to 30 feet in 1-foot steps. meters: Distances can be set in meters. Range: 0.3 to 9 meters in 0.3-meter steps. Front, Center, SurrRight, SurrBack Right, SurrBack Left, SurrLeft, Subwoofer Specify the distance from the each speaker to your listening position. 5.
HT-S5200_En.book 73 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup—Continued Audio Adjust Settings With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. 7. Audio Adjust Multiplex/Mono Settings Input (Mux) Main: The main channel is output (default). Sub: The sub channel is output. M/S: Both the main and sub channels are output. This setting determines which channel of a stereo multiplex source is output.
HT-S5200_En.book 74 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup—Continued Dolby EX Input Signal Setting Dolby EX Auto: When the source is Dolby EX, you can select the Dolby EX listening mode. Manual: When the source is Dolby EX, you can select any of the listening modes compatible with this format (e.g., Dolby EX, Dolby Pro Logic IIx, etc.) (default). This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected.
HT-S5200_En.book 75 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup—Continued Hardware Setup This section explains items on the Hardware menu. 8. Hardware Remote ID When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from 1, the default, to 2 or 3.
HT-S5200_En.book 76 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup—Continued Using the Audio Settings You can change various audio settings by pressing the [AUDIO] button. 1 Press the [RECEIVER] button followed by the [AUDIO] button. RECEIVER 2 Use the Up and Down [q]/[w] buttons to select an item. qwer 3 Use the Left and Right [e]/[r] buttons to change the setting. Repeat this step for the other settings.
HT-S5200_En.book 77 ページ 2009年3月9日 月曜日 午後4時31分 Advanced Setup—Continued Audyssey Dynamic Volume™ Dyn Vol See “Dyn Vol” of “Audio Adjust Settings” on page 74. Music Optimizer The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that use “lossy” compression, such as MP3. Note: The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48kHz and analog audio input signals.
HT-S5200_En.book 78 ページ 2009年3月9日 月曜日 午後4時31分 Controlling Other Components You can control your DVD player, CD player, and other components with the AV receiver’s remote controller. To control another component, you must first enter that component’s remote control code to a REMOTE MODE button. This section explains how to enter remote control codes and how to control your other components. 1 Look up the appropriate remote control code in the separate Remote Control Codes list.
HT-S5200_En.book 79 ページ 2009年3月9日 月曜日 午後4時31分 Controlling Other Components—Continued Remote Control Codes for Onkyo Components Connected via u Onkyo components that are connected via u are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. 1 2 Make sure the Onkyo component is connected with an u cable and an analog audio cable (RCA). See page 37 for details.
HT-S5200_En.book 80 ページ 2009年3月9日 月曜日 午後4時31分 Controlling Other Components—Continued Controlling a DVD Player, or DVD Recorder By pressing the REMOTE MODE button that’s been programmed with the remote control code for your DVD player (HD DVD, Blu-ray, or TV/DVD combination), you can control your player with the following buttons. e Playback buttons Play [1], Pause [3], Stop [2], Fast Reverse [5], Fast forward [4], Previous [7], and Next [6].
HT-S5200_En.book 81 ページ 2009年3月9日 月曜日 午後4時31分 Controlling Other Components—Continued Controlling a CD Player, CD Recorder, or MD Player By pressing the REMOTE MODE button that’s been programmed with the remote control code for your CD player, CD recorder, or MD player, you can control your player with the following buttons. a ON/STANDBY button Set the component to On or Standby. The [CD] button is preprogrammed with the remote control code for controlling an Onkyo CD player.
HT-S5200_En.book 82 ページ 2009年3月9日 月曜日 午後4時31分 Controlling Other Components—Continued Controlling a Cassette Recorder By pressing the REMOTE MODE button that’s been programmed with the remote control code for your cassette recorder, you can control your cassette recorder with the following buttons. The [TV/TAPE] button is preprogrammed with the remote control code for controlling an Onkyo cassette recorder when used with an u connection.
HT-S5200_En.book 83 ページ 2009年3月9日 月曜日 午後4時31分 Controlling Other Components—Continued Controlling an RI Dock By pressing the REMOTE MODE button that’s been programmed with the remote control code for your Dock, you can control your iPod in the Dock with the following buttons. For some RI docks, the “ON/STANDBY” button may not work with a remote control code 82990 (without u). In this case, make an u connection and enter a remote control code 82351 (with u).
HT-S5200_En.book 84 ページ 2009年3月9日 月曜日 午後4時31分 Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting your Onkyo dealer. To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [ON/STANDBY] button.
HT-S5200_En.book 85 ページ 2009年3月9日 月曜日 午後4時31分 Troubleshooting—Continued The subwoofer produces no sound • The subwoofer outputs no sound while only speaker set B is on. Turn on speaker set A. • If the source material contains no audio in the LFE channel, the subwoofer produces no sound. • Check the “3. Sp Config” (page 70). • On the AV receiver, the subwoofer setting in the “3. Sp Config” is set to “No”. Set the subwoofer setting to “Yes”.
HT-S5200_En.book 86 ページ 2009年3月9日 月曜日 午後4時31分 Troubleshooting—Continued • Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary. • If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed. • Make sure you’ve selected the correct remote controller mode (pages 16 and 80–83). • Make sure you’ve entered the correct remote control code (page 78).
HT-S5200_En.book 87 ページ 2009年3月9日 月曜日 午後4時31分 Troubleshooting—Continued The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. 1. While holding down the input selector button for the input source that you want to set, press the [SETUP] button. 2. Use the Left and Right [e]/[r] buttons to change the setting. 3. Press the [SETUP] button when you’ve finished.
HT-S5200_En.book 88 ページ 2009年3月9日 月曜日 午後4時31分 Specifications HT-R570 Amplifier Section General Rated Output Power 130 watts minimum continuous power per channel, 6 ohms, at 1 kHz with a maximum total harmonic distortion of 1% Dynamic Power 180 W (3Ω, Front) 160 W (4Ω, Front) 100 W (8Ω, Front) THD (Total Harmonic Distortion) 0.08% (1 kHz 1 W) Damping Factor 60 (Front, 1 kHz, 8Ω) Input Sensitivity and Impedance 200 mV/ 47 kΩ (LINE) Output Level and Impedance 200 mV/ 2.
HT-S5200_En.book 89 ページ 2009年3月9日 月曜日 午後4時31分 Specifications—Continued HTP-570 ■ Subwoofer (SKW-570) Type: Bass-reflex Input sensitivity/ Impedance: 140 mV/20 kΩ Maximum output power: 290 W (Dynamic power) Frequency response: 25 Hz–150 Hz Cabinet capacity: 38 L (1.34 cubic feet) Dimensions (W × H × D): 317.5 × 460 × 398 mm (12-1/2" × 18-1/8" × 15-11/16") (incl. projection) Weight: 10.9 kg (24.0 lbs.
HT-S5200_En.
HT-S5200_En.
HT-S5200_En.book 92 ページ 2009年3月9日 月曜日 午後4時31分 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.