Operation Manual
Advanced Settings (Setup Menu)
En-41
● Default values vary depending on the regions.
● The speaker "Distance" may be unable to be changed depending on the settings in "Configuration" -
"Speaker Channels" / "Subwoofer".
Level Calibration
Adjust the level of each speaker with the built-in test tone. Settings are automatically
configured if you use the Automatic Speaker Setup.
Setting Item Default Value Setting Details
Front Left 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
Center 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
Front Right 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
Height Left 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
● This cannot be selected in the following
conditions.
– The setting for "Configuration" - "Bi-Amp"
is "Yes"
– "Configuration" - "Powered Zone 2" is set
to "Yes" and ZONE 2 is on
Height Right 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
● This cannot be selected in the following
conditions.
– The setting for "Configuration" - "Bi-Amp"
is "Yes"
– "Configuration" - "Powered Zone 2" is set
to "Yes" and ZONE 2 is on
Setting Item Default Value Setting Details
Surround Right 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
Back Right 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
● This cannot be selected in the following
conditions.
– The setting for "Configuration" - "Bi-Amp"
is "Yes"
– "Configuration" - "Powered Zone 2" is set
to "Yes" and ZONE 2 is on
Back Left 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
● This cannot be selected in the following
conditions.
– The setting for "Configuration" - "Bi-Amp"
is "Yes"
– "Configuration" - "Powered Zone 2" is set
to "Yes" and ZONE 2 is on
Surround Left 0.0dB Select a value between "-12.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
Subwoofer 0.0dB Select a value between "-15.0 dB" and "+12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select
the desired level.
● The speaker "Level Calibration" may be unable to be changed depending on the settings in
"Configuration" - "Speaker Channels" / "Subwoofer".
● "Level Calibration" cannot be changed while muting is on.