User's Manual

ManualsBrandsONN ManualsAutomotiveCar Cup Holder Phone Mount with 10w Wireless Phone Charger

IMPORTANT

Please read this manual before using the unit to ensure safe and proper use.

 The unit will generate the magnetic/electric field; never place any medical

equipment; watches; credit card; magnetic record card or any magnetic

sensitive products close to the unit.

 Only phones with built-in QI wireless system can recharged by this unit. For

details, please refer the user’s manual of your phone.

 The design of the unit is indoor use. Never spill or spray any type of liquid on the

product.

 Do not use this product near water and moisture, for example: near a bathtub,

washbowl, kitchen sink or laundry tub; in a wet basement; or near a swimming

pool.

 Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

 Clean only with dry cloth. Unplug this product from external USB Charging

Devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry

cloth for cleaning.

 Do NOT place any heavy object on the Charging Surface. It may damage the unit.

 When replacement parts are required, be sure the service technician uses

replacement parts specified by the manufacturer or those that have the same

characteristics as the original parts. Unauthorized substitutions may result in fire

or electric shock or other hazards.

August 27, 2021_V1

Summary of content (9 pages)

PAGE 1
IMPORTANT Please read this manual before using the unit to ensure safe and proper use.  The unit will generate the magnetic/electric field; never place any medical equipment; watches; credit card; magnetic record card or any magnetic sensitive products close to the unit.  Only phones with built-in QI wireless system can recharged by this unit. For details, please refer the user’s manual of your phone.  The design of the unit is indoor use. Never spill or spray any type of liquid on the product.
PAGE 2
FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 3
INSTALLATION Before use, assembled the Car Mount to the Charger as follows: 1. Loosen the Knob on the Charger by turning it counterclockwise as illustrated below: 2. Insert the Car Cup Holder Phone Mount into the Charger as illustrated below: 3.
PAGE 4
. Loosen the Knob on the Mount by turning it counterclockwise as illustrated below: 5. Pull out the pivot arm to the needed height then tighten it by turning the knob clockwise as illustrated below: MOUNTING Mount the charger into your vehicle as follows: 1. Rotate the striped Circle counterclockwise to outspread the three Squares.
PAGE 5
2. Outspread the three Squares to suitable position based on the diameter of Car Cup Holder, Put the charger into the Car Cup Holder. CONNECTION Connect the Charger to your Car USB Charger (not included) as follows: 1. Connect the Type-C USB Plug from the supplied USB connection cable to the Type-C USB Port on the Charger as illustrated below: 2. Connect the full size USB Plug to the USB Port on your Car USB Charger (not included) as illustrated below: 3.
PAGE 6
WIRELESS CHARGING 1. Mount the unit into your vehicle then connect it to your Car USB Charger as previously instructed. 2. Press the Release Button on the rear of Charger to release the Clip as illustrated below: 3. Place your cell phone onto the Charging surface as illustrated below: 4.
PAGE 7
5. Closed the Clip to hold the cell phone as illustrated below: Notes: 1. To charge a cell phone with the Charger, the cell phone must be compatible with the Qi standard for wireless charging. 2. During charging, if the cell phone has a cover or case, it may disturb or prevent the wireless charging function of the cell phone. 3. The charging transmission distance of the unit is less than 5mm, the thickness of cell phone cover of case can NOT over 8mm. 4.
PAGE 8
DISCLAIMER This device only supports smartphones with wireless charging capability. If your smartphone does not have wireless charging capability, you may need to purchase a compatible wireless receiver. SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE Need help? We’re here for you every day from 7 a.m. - 9 p.m. CST.
PAGE 9
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.