OPEL Antara Operation, Safety, Maintenance
Data specific to your vehicle Please enter your vehicle’s data here to keep it easily accessible. This information is available under the section "Technical data" as well as on the identification plate.
Your Antara Make use of the Owner's Manual: is an intelligent combination of forwardlooking technology, impressive safety, environmental friendliness and economy. z Its "In brief" section will give you an initial overview. It now lies with you to drive your vehicle safely and ensure that it performs perfectly. This Owner's Manual provides you with all the necessary information to that end.
Back to overview
Contents Handling characteristics All Wheel Drive vehicles have a high centre of gravity due to the increased ground clearance required for off-road use. As with other vehicles of this type, failure to operate the vehicle correctly may result in loss of control or an accident. Please read the sections "All Wheel Drive" on page 121 and "Driving hints" on page 127. In brief .........................................................6 Locks, doors, windows ............................ 21 Seats, interior ...
In brief In brief To unlock and open the vehicle: Press button q, pull door handle 6 Door locks - see pages 30, 72, keys - see page 21, electronic immobiliser - see page 22, radio frequency remote control see page 23, central locking system - see page 25, anti-theft locking system - see page 27, anti-theft alarm system - see page 27.
In brief Front seat adjustment: Pull handle, slide seat, release handle Adjusting front seat backrests: Lift release lever on outboard side of seat 6 Seats - see page 36, seat position - see page 38. Move seat backrest to suit seating position. 7 Adjusting the lumbar support 3: Turn handwheel Adjust lumbar support to suit personal requirements. Do not lean on seat backrest whilst adjusting it. 6 Seats - see page 36, seat position - see page 38.
In brief Adjusting seat height 3: Raise or lower lever on outboard side of seat Adjusting head restraint height: Press release button, adjust height, then release Lever pumping action 6 Head restraints - see page 39, head restraint position – see page 39. upward: downward: raises seat lowers seat 6 Seats - see page 36, seat position – see page 38. Fitting seat belt: Draw seat belt smoothly from inertia reel, guide over shoulder and engage in buckle The belt must not be twisted at any point.
In brief To adjust interior mirror: Swivel mirror housing Swivel lever on underside of mirror housing to reduce dazzle at night. Take care when driving with interior mirror adjusted for night vision. Rear view may be slightly distorted in this position. 6 Mirrors - see page 31, automatic anti-dazzle interior mirror see page 32. Electrically adjustable exterior mirrors: Four way switch in driver’s door Move selector switch to L or R; four way switch adjusts corresponding mirror.
In brief Back to overview
In brief 1 Page Side air vents ................................... 104 2 Door window defroster vents ......... 104 3 Headlamp flash and main beam .... 14 turn signal lamps .............................. 14 Peripheral lighting............................. 98 cruise control 3 ............................... 140 11 Page Centre air vents............................... 104 Page 17 Accelerator pedal........................... 127 18 Driver’s airbag ..................................
In brief Control indicators u ABS (Anti-lock Brake System): see page 148. g Trailer indicator 3: see page 70. o Electronic immobiliser: see pages 22, 72. N 9 Door open: see page 72. C Change engine oil 3: 3 Engine electronics, transmission electronics 3: see pages 72, 134. N Preheating for diesel engines 3: see pages 19, 73. v Airbag systems 3, belt tensioners: see pages 44, 52. I DPF (Diesel particle filter) 3: see pages 73, 135. m Cruise control 3: see page 140.
In brief Steering column lock and ignition: Turn key to position ACC. To release lock, rotate steering wheel slightly Steering wheel adjustment: Move lever down, adjust height and distance, move lever up and engage Positions: Adjust steering wheel only with vehicle stationary and steering column lock released.
In brief Headlamp flash, main and dipped beam: Headlamp = Pull lever flash towards steering wheel Main beam = Push lever forwards Dipped beam = Pull lever back towards steering wheel Turn signal lamps: Lever in rest position Upwards = Right turn Downwards = Left turn 6 Turn signal lamps - see page 95. Hazard warning lamps: On = Press ¨ Off = Press ¨ again 6 Hazard warning lamps - see page 97. 6 Main beam, headlamp flash see page 95.
In brief Activate horn j: Press either side of the steering wheel The horn will sound regardless of ignition switch position. 6 Airbag systems - see page 52, remote control on steering wheel see page 101. Windscreen wipers: Move lever upwards J = Off $ = Timed interval wipe % = Slow & = Fast Press lever down from position J: Single swipe. 6 Windscreen wipers - see page 92, adjustable wiper interval - see page 92, further information - see pages 198, 202, 205.
In brief Operating windscreen and headlamp washer systems 3: Pull lever towards steering wheel 6 Windscreen and headlamp washer systems - see page 93, further information - see pages 199, 202, 205.
In brief Drying misted up or iced up windows: Set air distribution to position l, set the temperature rotary knob to red and fan to position 4, switch on heated rear window Ü To set automatic mode of Electronic Climate Control 3: Press AUTO button, set temperature using rotary knob Close centre air vents, open side air vents and direct them towards the door windows. 6 Electronic Climate Control (ECC) see page 111. 6 Heating, ventilation and air conditioning system - see pages 106, 109.
In brief Before starting-off, check: z Tyre pressures and condition. z Engine oil level and fluid levels in engine compartment (see page 192). z All windows, mirrors, exterior lighting and license plates are free from dirt, snow and ice and are operational. z Objects are securely located and will not be thrown forward in the event of sudden braking. z Seats, seat belts and mirrors are correctly adjusted.
In brief 19 Start attempts should not last longer than 15 seconds. If engine does not start, wait 10 seconds before repeating starting procedure. The increased engine speed automatically returns to normal idling speed as the engine temperature rises. Drive at a moderate speed, especially in cold weather, until normal engine operating temperatures have been reached.
In brief Advice when parking: z Always apply hand brake firmly and as firmly as possible on slopes. z Push key into ignition switch before removing (vehicles with automatic transmission 3: depress foot brake and shift into P before removing key). Turn steering wheel until lock is felt to engage (anti-theft protection).
Locks, doors, windows Locks, doors, windows Replacement keys Replacement keys .............................. Car Pass............................................... Key with foldaway key section 3 ...... Electronic immobiliser......................... Radio frequency remote control ....... Central locking system ....................... Tailgate ............................................... Mechanical anti-theft locking system 3 ........................................... Anti-theft alarm system 3 .....
Locks, doors, windows Note The immobiliser does not lock the doors. Therefore, after leaving the vehicle, always lock it and switch on the anti-theft alarm system 3 - see pages 25, 27. Electronic immobiliser The system checks whether the vehicle may be started using the key that has been inserted. If the key is recognised as "authorised", the vehicle can be started. The check is carried out via a transponder housed in the key.
Locks, doors, windows Treat the remote control unit with care: it should be protected against moisture, kept out of direct sunlight and should not be operated unnecessarily. Do not place heavy objects on the remote control unit, and avoid dropping it. The hazard warning lamps come on to indicate that the remote control is operational. 23 Central locking system see page 25. Mechanical anti-theft locking system 3 see page 27. Anti-theft alarm system 3 see page 27.
Locks, doors, windows Fault If the central locking system cannot be operated with the remote control, this may be due to the following reasons: Key with fixed key section: insert a small screwdriver in the notch on the cover and prise it open. Remove used battery, taking care to avoid touching the circuit board to other components. z The remote control is out of range. z The battery voltage of the remote control is too low. Change the battery in the remote control unit.
Locks, doors, windows 25 To unlock: Press button q on remote control - or Press central locking switch m in driver’s door. If no door is opened within approx. 30 seconds after the vehicle has been unlocked via the remote control, the vehicle is relocked automatically and anti-theft alarm 3 is reactivated. Central locking system For front doors, rear doors, tailgate and tank flap. To lock: Press button p on remote control - or With the doors closed, press central locking switch m in driver’s door.
Locks, doors, windows 9 Warning Ensure there are no obstructions and that there is adequate clearance when opening the tailgate. Do not drive with tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases could penetrate the vehicle interior. Tailgate To unlock and open Press button q on remote control - or Press central locking switch m in driver’s door.
Locks, doors, windows Mechanical anti-theft locking system 3 9 Warning Do not use the system if there are people in the vehicle. The doors cannot be unlocked from inside. To lock: All doors and the tailgate must be closed; press button p on remote control again within 3 seconds after locking - or Turn key in driver's door lock towards rear of vehicle again within 3 seconds after locking, then turn it back to the vertical position and remove.
Locks, doors, windows 9 Warning Do not use the system if there are passengers in the vehicle. The doors cannot be unlocked from the inside when the alarm is activated. The remote control unit is used to operate the anti-theft alarm system. To activate Always ensure that the doors, bonnet, tailgate, sun roof 3 and windows are properly closed and that there are no passengers left in the vehicle before activating anti-theft alarm system.
Locks, doors, windows To deactivate Press button q on remote control - or Unlock driver’s door by turning key in door lock towards front of vehicle, then turn it back to the vertical position and remove: Alarm While the alarm system is switched on, the alarm can be triggered, indicated by: z Hazard warning lamps flash twice, z All doors are unlocked, z Anti-theft system is deactivated. The number and duration of the alarms are legally established.
Locks, doors, windows Child safety locks 9 Warning Use the child safety locks whenever children are occupying the rear seats. Disregard may lead to injuries or endanger life. Vehicle passengers must be informed accordingly. To engage lock, open door, insert key into child safety lock and turn lock from the vertical to the horizontal position. Door cannot then be opened from inside. To unlock door while child safety lock is activated, pull up lock button and open door from outside.
Locks, doors, windows For the safety of pedestrians, the exterior mirrors will swing out of their normal mounting position in the event of an accident-like impact. As exterior mirrors are convex, objects are closer than they appear. Use interior mirror to judge size and distance of objects. Do not scrape ice from exterior mirrors or force them if frozen. Use a de-icer. 31 Automatic anti-dazzle exterior mirrors 3 Dazzle is automatically reduced.
Locks, doors, windows Electric windows 9 Warning Care must be taken when operating the electrically operated door windows. There is a risk of injury, particularly for children, and a danger that articles could become trapped. Vehicle passengers must be informed accordingly. Automatic anti-dazzle interior mirror 3 Dazzle is automatically reduced. If there are children on the rear seats, press the switch in the driver’s door to lock rear window operation.
Locks, doors, windows 33 Safety function 3 If the window glass encounters resistance above the middle of the window during automatic closing, it will stop immediately and will be opened again. In the event of difficulty due to frost or the like, press the relevant window switch several times until the window is closed. Additional switches are located in the front passenger’s door and the rear doors. The rear windows do not open fully.
Locks, doors, windows To open Press switch rearwards; it will open automatically unless the switch is pressed again in another direction, or released. To close Press and hold switch forwards. Release switch when sun roof reaches desired position. To tilt Press and hold switch upwards. Release switch when sun roof reaches desired position. Sun visors Slide/tilt sun roof 3 Use the sun visor to protect from glare by pulling it up, down or swivelling it to the side.
Locks, doors, windows 35 Note z If the top of the sun roof is wet, tilt it to allow water to run off before opening the sun roof. z When carrying a roof load, check the clearance of the sun roof, to avoid damage. 9 Warning Care must be taken when operating the sun roof. Do not place any objects or body parts in the sun roof opening. Keep sun roof clear of debris. Do not place heavy objects on or around sun roof. When leaving the vehicle unattended, ensure the sun roof is fully closed.
Seats, interior Seats, interior Front seats .......................................... Rear seats............................................ Seat belts............................................. Child restraint systems 3 ................... Airbag systems ................................... Storage ................................................ Drink holders ....................................... Ashtrays 3........................................... Warning triangle ¨ 3, First aid kit + 3 ......
Seats, interior 37 Electrically adjustable front seat 3 9 Warning Care must be taken when operating electrically adjustable seats. There is a risk of injury, particularly for children and a danger that articles could become trapped. Keep a close watch on the seats when adjusting them. Vehicle passengers must be informed accordingly. Adjusting the lumbar support 3 To adjust, turn the handwheel whilst relieving the load on the backrest. Adjusting seat height 3 To adjust, operate lever on side of seat.
Seats, interior Seat position Adjust driver’s seat such that, with the driver sitting upright, the steering wheel is held in the area of its upper spokes with the driver’s arms slightly bent. Slide front passenger’s seat as far back as it will go. The seat backrests must not be tilted back too far (recommended maximum tilting angle approx. 25°). 9 Warning Adjustment The seat position can be adjusted by means of switches on the outboard side of the seat.
Seats, interior 39 Active head restraints 3 In the event of a rear-end impact, the active head restraints automatically tilt forwards. The head is more effectively supported by the head restraint and the danger of hyperextension in the area of the cervical vertebra is reduced. Do not attach objects or components that are not approved for your vehicle to the head restraints.
Seats, interior Removing the head restraints Insert a suitable tool into the small hole in the side of the guide sleeve without the release button and depress the lock. Press the release button on the other guide sleeve and pull up the head restraint. Stow head restraints securely in luggage compartment. Front seat armrest 3 The armrest can be slid forwards. Pull up and hold upper lever and slide the armrest forwards.
Seats, interior 41 To raise the seat, lift backrest release lever and push backrest to upright position. Push and pull on seat backrest to ensure it is locked, thus avoiding excessive forward movement in the event of a collision. 9 Warning If longer objects, e.g. skis, are to be carried on the back of the front passenger’s seat backrest, ensure they are not in the area in which the front passenger’s airbag inflates or in the area between the seat backrest and the vehicle body.
Seats, interior Seat belts 9 Warning Three-stage restraint system The system comprises: When folding the backrest, use caution beware of moving parts. z Three-point seat belts. z Belt tensioners, with load limiters, on the front seats. Safety net 3 - see page 60. z Airbag systems for driver, front passenger and rear outboard seat occupants. Restoring rear seat backrests Lift and push backrest up and backwards to restore it to its original position.
Seats, interior z The airbag system is additionally triggered in the event of a serious accident involving a frontal impact, and forms a safety cushion for the driver and front passenger. In the event of a side impact, the side airbag system 3 protects the occupants in the front of the vehicle, and the curtain airbag system protects both front and rear outboard seat occupants. 9 Warning The airbag system serves to supplement the three-point seat belts and belt tensioners.
Seats, interior Belt force limiters Load limiters on the front seats reduce the impact on the seat occupant’s body from a tensioning belt, in the event of a severe frontal collision. The belt force is controlled, to reduce the risk of belt-inflicted injury. Actuation of belt tensioners The belt tensioners actuate only once and must be replaced by a workshop after activation.
Seats, interior The system’s integrated self-diagnostics allows faults to be quickly remedied. Important z Accessories not released for your vehicle type and other objects must not be fixed or placed within the action zone of the belt tensioners, as they may result in injury if the belt tensioners are triggered.
Seats, interior Using the belts Fitting the belt Pull the belt out evenly from the retractor and guide it over the shoulder, making certain that it is not twisted. Insert the latch plate into the buckle. The seat backrest must not be tilted back too far (the recommended maximum tilting angle is approx. 25°). The lap belt must not be twisted and must fit snugly across the body. Tension the belt frequently whilst driving by tugging the diagonal part of the belt.
Seats, interior 47 Child restraint systems 3 Opel child restraint systems are designed specifically for your vehicle and thus provide optimum safety for your child in the event of an impact. The use of an Opel child restraint system is therefore recommended. If a different child safety seat is used, follow the manufacturer’s instructions for fitting and use. 9 Warning Seat belt height adjustment of front seat belt upper anchorage points z Do not adjust height whilst driving.
Seats, interior Note z Children under 12 years or under 150 cm tall should only travel in an appropriate child safety seat. z Never carry a child whilst travelling in the vehicle. The child will become too heavy to hold in the event of a collision. z When transporting children, use a child restraint system that is suitable for the child's weight, age and height. z Ensure that the child restraint system to be installed is compatible with the vehicle type.
Seats, interior Permissible options for fitting a child safety seat Weight and age class On front passenger’s seat 0: up to 10 kg or approx. X 10 months 0+: up to 13 kg or approx. X 2 years I: 9 to 18 kg or approx. X 8 months to 4 years II: 15 to 25 kg or approx. X 3 to 7 years III: 22 to 36 kg or approx. X 6 to 12 years U = On outboard rear seats On centre rear seat U, + X U, + X U, +, ++ X U X U X + = ++ = X = 49 Universal suitability in conjunction with the three-point seat belt.
Seats, interior ISOFIX child restraint systems 3 The instructions accompanying the ISOFIX child restraint system are to be expressly followed. IL = Suitable for particular ISOFIX child restraint systems specified in the list. These ISOFIX systems are of the ’vehicle-specific’, ’restricted’ or ’semiuniversal’ type. IUF = X = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight and age class.
Seats, interior 51 Permissible options for fitting an ISOFIX child safety seat Weight and age class 0: up to 10 kg or approx. 10 months 0+: up to 13 kg or approx. 2 years I: 9 to 18 kg or approx.
Seats, interior Mounting brackets for ISOFIX child restraint systems The brackets located between the backrest and seat cushion are used for mounting ISOFIX child restraint systems. The instructions accompanying the ISOFIX child restraint system are to be expressly followed. Only ISOFIX child restraint systems approved for the vehicle may be used.
Seats, interior When triggered, the driver’s and front passenger’s airbags inflate in milliseconds and form safety cushions for the driver and front passenger. Forward movement of driver and front passenger is checked and the risk of injuries to the upper body and head thereby substantially reduced. z No impairment of view will occur, as airbags inflate and deflate so quickly.
Seats, interior When triggered, the side airbag inflates in milliseconds and forms a safety cushion for the driver and/or front passenger in the respective door area. The risk of injury to the upper body and pelvis in the event of a side impact is thereby substantially reduced. 9 Warning There must be no objects in the area in which the airbag inflates or in the area between the seat backrests and the vehicle body.
Seats, interior 55 The side airbags will not be triggered in the event of: z the ignition being switched off, z frontal collisions, z accidents in which the vehicle overturns, if lateral impact is insufficient for side airbag deployment, z collisions involving a rear impact, z collisions involving a side impact outside the passenger cell.
Seats, interior When triggered, the curtain airbag inflates in milliseconds and provides a safety barrier in the head area on the respective side of the vehicle. This reduces the risk of injury to the head considerably in the event of a side impact. 9 Warning There must be no objects in the area in which the airbag inflates. Do not place hands, arms or other body parts on the covers of the airbag systems.
Seats, interior 9 Warning Have the cause of the fault remedied by a workshop. The system's integral self-diagnosis facility allows faults to be quickly remedied. 9 Warning Disregard of these instructions may lead to injuries or endanger life. Important z Accessories not released for your vehicle type and other objects must not be affixed or placed in the area in which the airbags inflate, as they could cause injury when the airbags are triggered.
Seats, interior z After airbags deflate, you may notice a burning smell, smoke and white powder in the interior, which is normal. Although they may cause skin or eye irritation, these substances are non-toxic. z Hazard warning lamps may flash and locked doors may be unlocked automatically when airbags deploy 3.
Seats, interior 59 Notes on loading the vehicle: See page 63. 9 Warning Do not place any heavy or sharp objects on the cover. Loose objects in the luggage compartment should be secured safely. Storage Luggage compartment cover To close Pull luggage compartment cover towards rear of vehicle using handle and insert retainers into brackets on either side of luggage compartment. To remove Open luggage compartment cover.
Seats, interior Safety net 3 The safety net can be mounted behind the rear seats or, if the rear seat backrests are folded, in front of the rear seats. Passengers must not be transported behind the safety net. Fitting There are four installation openings in the roof frame, two located in front of and two behind the rear seats. In front of and behind the rear seats on both sides of the vehicle are the hook holders (lashing eyes) for the lower strap hooks.
Seats, interior Designed for carrying small, light items only, the luggage floor net 3 helps keep loads from moving during sharp turns or quick starts and stops. 9 Warning Do not stack loads higher than the upper end of the safety net. To install: attach the four net hooks to the lashing eyes mounted on the luggage compartment floor. Avoid applying excessive force to the safety net or hanging heavy items from it.
Seats, interior FlexOrganizer 3 Flexible system for dividing the luggage compartment or securing loads. The system consists of: z z z z adapters variable partition net mesh pockets for the side walls hooks in the luggage compartment Components are mounted in the two guide rails in the side walls of the luggage compartment by means of adapters or hooks.
Seats, interior 63 Notes on loading the vehicle z Heavy objects in the luggage compartment should be placed as far forward as possible. If objects are to be stacked, the heavier objects should be placed at the bottom. With rear seats in the folded position, or with safety net 3 installed behind rear seats, objects must not be stacked higher than the seat backrests. Luggage compartment storage 3 Trays on both sides of the luggage compartment floor.
Seats, interior z Close the luggage compartment cover to prevent the objects from being reflected in the rear window. z If the backrests are not folded down when transporting objects in the luggage compartment, they must be engaged in their upright position see page 41. z Do not allow the load to protrude above the upper edge of the rear seat backrests, or if the rear seat backrests have been folded down onto the seat cushions, above the upper edge of the front seat backrests.
Seats, interior Sunglass holder To open: push the rear part of the front reading lamps cover. To close: pull up cover and push it until it latches into place. Do not store heavy items in the stowage compartment. 65 Console box in front armrest 3 To open: pull up lower lever and lift the lid. Console box in rear armrest 3 To open: pull up lid of rear centre armrest. To close: lower lid and push it down until it latches into position. To close: lower lid and push it down until it latches into position.
Seats, interior Console net 3 Located in the front passenger’s footwell. Front passenger’s seat undertray 3 Pull up on front of tray then pull it forwards. Push the tray towards the seat to return it to its original position. Storage compartment 3 Located in rear of centre console. To open: press button above the storage compartment.
Seats, interior 67 Ashtrays 3 Card holder Located below instrument panel on driver’s side. Insert a card into the slot for convenient use. To be used only for ash and not for combustible rubbish. 9 Warning Coin storage Open by pulling handle on coin storage door (located below card holder) towards you. Push door firmly to close. Disregard of these instructions may lead to injuries or endanger life. Vehicle passengers must be informed accordingly.
Seats, interior Warning triangle ¨ 3, First aid kit + 3 Your first aid kit and warning triangle can be accommodated below the floor cover in the luggage compartment. Portable front ashtray 3 Located in front drink holder. To open: gently lift up lid. Illuminates depending on outside light conditions. To empty: rotate upper part of ashtray anti-clockwise and remove. After use, close lid firmly.
Seats, interior Accessory sockets Located in the rear centre console between the front seats and in the right-hand side of the luggage compartment 3. Operational with ignition switch in positions ACC or ON. Pull the cap out to use the accessory socket, and replace it when not in use. The socket for the cigarette lighter can also be used to connect electrical accessories when the ignition is switched on. Use of accessory sockets while the engine is not running will discharge the battery.
Instruments, controls Instruments, controls Control indicators ............................... Instrument display .............................. Information display ............................ Display of current tyre pressure 3 .... Check control 3 .................................. Warning buzzers................................. Windscreen wipers.............................. 70 75 76 91 91 92 92 Control indicators 4 The control indicators described here are not present in all vehicles.
Instruments, controls r B If it stays illuminated while driving, there is a fault in the system - see page 142. If it flashes during driving, the AWD system is temporarily disabled. 5 If it illuminates, there is a fault in the system. Consult a workshop as soon as possible. Park pilot 3 Illuminates in yellow when ignition is switched on, then extinguishes. DCS (Descent Control System) Both control indicators illuminate when ignition is switched on, then extinguish.
Instruments, controls o 1 O If it remains illuminated after the ignition is on, there is a fault in the immobiliser system; the engine cannot be started see page 22. Illuminates when tailgate is open or not securely latched. Rapid flash; failure of a turn signal bulb or the corresponding fuse or failure of a trailer turn signal bulb 3. Both control indicators flash when the hazard warning lamps are active. Electronic immobiliser Illuminates in red when ignition is switched on, then extinguishes.
Instruments, controls > C Front fog lamps Illuminates in green when front fog lamps are switched on - see page 96. Change engine oil 3 Illuminates in yellow when ignition is switched on, then extinguishes. r Illuminates to indicate that engine oil needs changing within approx. 1000 km (600 miles). Engine power may be decreased. Fog tail lamp Illuminates in yellow when the fog tail lamp is switched on - see page 96.
Instruments, controls a Anti-theft alarm system activation without monitoring of passenger compartment and vehicle tilt 3 see page 28. I Engine oil pressure Illuminates in red when ignition is switched on. Extinguishes after engine is started. Can illuminate intermittently when idling with hot engine; must extinguish when engine speed is increased.
Instruments, controls Instrument display Tachometer Making use of the tachometer helps to save fuel; it indicates the engine speed in revolutions per minute (rpm). Red warning zone on right; maximum permissible engine speed exceeded, danger to engine. If possible, drive in each gear in the low engine speed range (between approx. 2000 and 3000 rpm) and maintain an even vehicle speed to maximise fuel efficiency. Speedometer Indicates the vehicle speed.
Instruments, controls 11:25 } 21 .5°C Range RDS [TP] 257km Fuel gauge Indicates fuel level when the ignition is on. After adding fuel and restarting engine, fuel gauge pointer slowly moves to show new fuel level. When fuel gauge indicates that fuel supply is low, control indicator Y illuminates: fill up fuel tank as soon as possible see page 132. Transmission display 3 Display of the selected gear or mode with automatic transmission 3. P Park position. R Reverse gear. N Neutral. D Automatic mode.
Instruments, controls The type of information and how it is displayed depends on the equipment of the vehicle and the settings of the trip computer 3 and Infotainment system. Range Some information appears on the display in an abbreviated form. 257 km Aver. Consump. 7.0 Ltr./100km Inst. Consumpt. 7.6 Ltr./100km 19,5° 19:36 Infotainment system – see Infotainment system instruction manual. An F in the display indicates a fault. Have the cause of the fault remedied by a workshop. 77 : 11:25 } -1 .
Instruments, controls 11:25 } Slippery road -2,5°C 21 .5°C Range 257km OK In vehicles with graphical information display 3 or colour information display 3, a warning message appears on the display as a warning for icy road surfaces. There is no message below -5 °C. Board information display, selecting functions Functions and settings of some equipment can be accessed via the board information display.
Instruments, controls 79 The functions are displayed in the following order: 11:25 } 21 .5°C System To select using the left adjuster wheel on the steering wheel: Turn up Turn down Press Previous menu item. Next menu item. Select marked item, confirm command. If check control 3 issues a warning message, the display is blocked from other functions. Acknowledge the message by pressing the OK button or the left adjuster wheel. If there are several warning messages, acknowledge them one at a time.
Instruments, controls The automatic setting is indicated by } in the display. 11:25 } 21 .5°C Clock Sync.On To correct time with the help of RDS, select the menu item for time synchronisation from the Settings menu. Make the desired setting. Setting date and time Select the menu item for time and date setting from the Settings menu. 11:25 } 21 .5°C English Make the desired setting. The setting is saved when the menu item is exited.
Instruments, controls 11:25 } 21 .5°C Unit Europe-SI Board information display, trip computer 3 The trip computer provides information on driving data, which is continually recorded and evaluated electronically. Access trip computer vehicle data by pressing the BC button on the Infotainment system or the left adjuster wheel on the steering wheel. Some of the functions appear on the display in an abbreviated form. Setting units of measure You can select which units of measure are to be used.
Instruments, controls Average consumption Display of average consumption. The measurement can be restarted at any time – see "Resetting trip computer information". Effective consumption Displays amount of fuel consumed. The measurement can be restarted at any time – see "Resetting trip computer information". Average speed Display of average speed. The measurement can be restarted at any time - see "Resetting trip computer information".
Instruments, controls 11:25 } 21 .5°C Stop Watch 01:22:32 h Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. Range To start, press left arrow button to select menu item Start and press OK button to start/stop. To reset, press left arrow button to select menu item Reset and press OK button.
Instruments, controls To select using the arrow buttons: To select using the multifunction knob: Select menu items via menus and with the buttons on the Infotainment system. Turn If check control 3 issues a warning message, the display is blocked from other functions. Acknowledge the message by pressing the right or left arrow button. If there are several warning messages, acknowledge them one at a time. Press Mark menu items or commands, select functions. Select marked item, confirm command.
Instruments, controls 7 FM [TP] CDin Settings Time, Date 19,5° 19:36 7 Time, Date 85 19,5° 19:36 19:36 Time 19:36 10 . 07 . 2004 Date 10 . 07 . 2004 Language 90.6 MHz Units Contrast Day / Night 19,5° 19:36 For each functional area there is a main page (Main), which is selected at the top edge of the display: z z z z Audio Navigation 3 Telephone 3 Trip computer 3 For audio, navigation 3 and telephone 3 functions – see Infotainment system instruction manual. 6 Synchron.
Instruments, controls Correcting time 3 With the navigation system, date and time are set automatically upon receipt of a GPS1) satellite signal. If the displayed time does not match local time, it can be corrected manually or automatically by receiving an RDS2) time signal 3. Some RDS transmitters do not send correct time signals. If the incorrect time is displayed often, deactivate automatic time synchronisation 3 and set the time manually.
Instruments, controls 7 Settings 19,5° 19:36 7 Contrast 19,5° 19:36 Time, Date Language ~ Europe-SI Units | | | Japan Contrast Day / Night 12 Great Britain 6 Ign. logic Select menu item Units from the Settings menu. The available units are displayed. Select the desired unit. Setting display mode 3 The display can be adjusted to suit the light conditions: black or coloured text on a light background or white or coloured text on a dark background.
Instruments, controls Ü Board Computer BC 1 BC 2 Timer 19,5° 19:36 All values 1 257.0 Ø 40 8 31.0 Ø 7.0 Tyres Range km km/h Ltr. Ltr./100km Graphical information display 3 or colour information display 3, trip computer 3 The trip computers provide information on driving data, which is continually recorded and evaluated electronically. The trip computer main page provides information on range, average consumption and instantaneous consumption.
Instruments, controls Distance travelled Displays number of kilometres (miles) driven. The measurement can be restarted at any time - see "Resetting trip computer information". Ü Board Computer BC 1 Average speed Display of average speed. The measurement can be restarted at any time - see "Resetting trip computer information". BC 2 Timer Tyres Average consumption Display of average consumption. The measurement can be restarted at any time - see "Resetting trip computer information". 257.0 40 1 Ø 31.
Instruments, controls Ü Reset BC 1 19,5° 19:36 All values 257.0 Ø 40 31.0 Ø 7.0 Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. Ü Board Computer BC 2 km km/h 19,5° 19:36 BC 1 00:00:00 Timer Tyres Start Ltr. Reset Ltr./100km Options To reset all information of a trip computer, select menu item All values.
Instruments, controls Check control 3 The desired stop watch display can be selected from the Options menu 3: Driving Time excl. Stops The time the vehicle is in motion is recorded. Stationary time is not included. Driving Time incl. Stops The time the vehicle is in motion is recorded. The time the vehicle is stationary with the key in the ignition switch is included. Travel Time Measurement of the time from manual activation via Start to manual deactivation via Reset.
Instruments, controls Warning buzzers While driving: z when operating the turn signals. z if driver’s or passenger’s seat belt 3 is not engaged when the seat is occupied and vehicle speed exceeds approx. 22 km/h (14 mph). When the vehicle is parked and driver’s door is opened: z with exterior lamps switched on. z when the key is in the ignition switch. 6 Seat belt warning chimes see pages 46, 72, driving hints - see page 127, save fuel, protect the environment see page 129.
Instruments, controls Automatic wiping with rain sensor 3 To activate, move lever upwards to automatic wiping with rain sensor position $. The rain sensor detects the amount of water on the windscreen and automatically regulates the windscreen wipers. The wipers operate for one cycle to check the system when the ignition switch is turned to ACC. To turn wipers off, move lever to position J. Keep the rain sensor area clean by activating the windscreen washer system.
Lighting Lighting Main beam, headlamp flash ............. 95 Automatic dipped beam activation 3 95 Turn signal lamps ............................... 95 Front fog lamps > ............................. 96 Fog tail lamp r .................................. 96 Reversing lamps.................................. 96 Centre high-mounted stop lamp....... 96 Hazard warning lamps ...................... 97 Headlamp range adjustment q........ 97 Peripheral lighting ..............................
Lighting Main beam, headlamp flash To switch from dipped beam to main beam, push lever forwards. To switch back to dipped beam, pull lever back towards steering wheel. To activate the headlamp flash, pull lever towards steering wheel. Main beam is engaged for the duration of activation. The blue control indicator P is illuminated when main beam or headlamp flash is on.
Lighting Reversing lamps Come on when reverse gear is engaged and ignition is switched on. Centre high-mounted stop lamp Comes on when the brakes are applied, acting as a third stop lamp, to supplement the brake lamps. Front fog lamps > On = Off = Press button >, > illuminates in instrument panel. Press button > again, > extinguishes in instrument panel. The front fog lamps can only be switched on when both the ignition and headlamps are on.
Lighting 97 Vehicles with level control system z Front seats occupied = 0 z All seats occupied = 1 z All seats occupied and load in luggage compartment = 1 z Driver’s seat occupied and load = in luggage compartment 2 Automatic headlamp range adjustment 3 On vehicles with Xenon headlamps, the range of the headlamps is adjusted automatically based on vehicle load. Hazard warning lamps Headlamp range adjustment q To switch on, press button ¨.
Lighting Peripheral lighting The dipped beam and reversing lamps illuminate for approx. 30 seconds after the driver exits the vehicle and closes the door. To activate function: 1. 2. 3. 4. Switch off ignition. Remove ignition key. Open driver’s door. Pull turn signal lever towards steering wheel. If the driver’s door is left open, the lamps will extinguish after two minutes.
Lighting Courtesy lamps can be turned off immediately by pressing button K. 99 Front reading lamps Left and right reading lamps are individually operable. With ignition on: Rear interior lamps Press button to turn on left and right rear interior lamps individually. On Off Press button again to turn the lamp off. = Press button L or M = Press button again 9 Warning Avoid using interior lamps while driving in the dark, as they can reduce driver visibility.
Lighting Front door lamps Come on when a door is opened. Once all doors are closed, the front door lamps extinguish after approx. 10 seconds. If the doors are left open, the lamps will stay on for approx. 10 minutes. Front door lamps can also be turned off immediately by pressing button K in the roof lining. Ignition switch illumination Comes on when you open a door. Luggage compartment lamps Come on when a door or the tailgate is opened.
Infotainment system Infotainment system 101 Radio reception 3 The radio is operated as described in the operating instructions supplied. Vehicle radio reception will differ from that obtained with domestic radios. Radio reception 3............................... Steering wheel mounted remote control ............................................... Mobile telephones and radio equipment (CB) 3 ............................ Infotainment and navigation systems 3..........................................
Infotainment system Mobile telephones and radio equipment (CB) 3 The Opel installation instructions and the operating guidelines provided by the telephone manufacturer must be observed when fitting and operating a mobile telephone. Failure to do so could invalidate the vehicle’s operating permit (EU Directive 95/54/EG). Requirements to ensure trouble-free operation: z Professionally installed exterior antenna, to obtain the maximum range possible z Maximum transmission power 10 W.
Climate control 103 Climate control Heating and ventilation system, air conditioning system ................... Electronic Climate Control (ECC) 3 ... Air vents .............................................. Heated rear window, heated exterior mirrors 3 ................ Heated front seats 3.......................... Glove compartment cooling 3 .......... Heating and ventilation system ........ Air recirculation mode........................ Air conditioning system......................
Climate control Door window defroster vents Air distribution rotary knob set to l or J; cooled or heated air will be directed onto the windscreen and onto the door windows (mainly in the area of the exterior mirrors). Rear air vents Operational when air distribution rotary knob is set to L, K or J. Cooled or heated air is directed into the footwell area of the rear passenger compartment.
Climate control Heated rear window, heated exterior mirrors 3 Operational only in ignition switch positions ACC or ON. Press button Ü Press button Ü again = = On Off Control indicator in button. Turn off as soon as vision is clear. Rear window and exterior mirror heating is switched off automatically after approx. 15 minutes. To avoid discharging the battery, do not operate when you are just starting the vehicle, or if there is a build up of snow or ice. Operate only with the engine running.
Climate control Heating and ventilation system Left-hand rotary knob: Air distribution M To head area via adjustable air vents L To head area via adjustable air vents and to footwell K To footwell J To windscreen, front door windows and footwell l To windscreen, front door windows and head area via adjustable air vents Central rotary knob: Temperature To red = Warm To blue = Cold Right-hand rotary knob: Air flow Four fan speeds: x 4 = Off = Maximum air flow The rate of air flow is determine
Climate control Heating The amount of heat is dependent on the engine temperature and is thus not fully attained until the engine is warm. For rapid warming of the passenger’s compartment: z Activate air recirculation mode 4. z Set the air distribution rotary knob to K or L. z Turn temperature rotary knob to red area for warm air. z Set fan to 4. Ventilation z Turn air recirculation mode 4 off. z For maximum ventilation to head area: set air distribution rotary knob to M.
Climate control z Set fan to 4. z Close centre air vents. z Open adjustable side air vents and direct them towards door windows. z Switch on heated rear window Ü. For simultaneous warming of the footwell, set air distribution rotary knob to J. Air conditioning n and air recirculation 4 are turned on automatically to improve defrosting efficiency when position J or l is selected. Heating the footwell z Set air distribution rotary knob to K. z Turn temperature rotary knob to red area for warm air.
Climate control 109 Air recirculation mode should only be used for brief periods, due to gradual deterioration in air quality and an increase in humidity, causing windows to mist up. Driving with air recirculation mode on for extended periods may cause vehicle occupants to feel drowsy. Press button 4 again to turn air recirculation mode off; control indicator in the button extinguishes and outside air is drawn into the vehicle.
Climate control Once activated, the air conditioning system is operated via the normal heating and ventilation controls. Even with air conditioning on, if temperature rotary knob is set to warm, the vehicle will still produce warm air in the passenger compartment. To improve efficiency of the air conditioning, always close the windows, to prevent chilled air from escaping.
Climate control 111 Electronic Climate Control (ECC) 3 Provides the greatest amount of comfort in the vehicle interior, regardless of the weather, outside temperature or season. Maximum cooling Open windows and sun roof 3 briefly so that warm air can escape rapidly. z Press button n (to switch on air conditioning system).
Climate control Temperature preset The central rotary knob can be used to set the temperature; 22 °C, 24 °C and 26 °C appear on the rotary knob. Intermediate settings are possible. The selected temperature is maintained. At the lowest or highest temperature setting, the system works at maximum cooling or heating.
Climate control 113 Air recirculation mode 4 is automatically switched off. Air conditioning n switches on. To switch off window demisting and defrosting, press button V again, press AUTO button, adjust fan speed or air distribution rotary knob. Manual settings Under certain circumstances (e.g. iced or misted windows), the functions of the system can be modified manually.
Climate control Note Maintenance If the windscreen mists up in damp weather, temporarily set the system as described under "Window demisting and defrosting" - see pages 108, 113. To ensure continuously efficient performance and prolong the life of the air conditioning system, it must be switched on for a few minutes once a week, irrespective of the weather and time of year. Cooling is most efficient when the windows are closed.
Driving and operation Driving and operation Automatic transmission 3 ................. All Wheel Drive.................................... Driving hints ........................................ Save fuel, protect the environment... Fuels, refuelling................................... Catalytic converter, exhaust emissions........................................... Drive control systems ......................... Brake system....................................... Anti-lock Brake System (ABS) u.......
Driving and operation Selector lever can only be moved out of P or N with the ignition switched on and the foot brake depressed (selector lever lock). To engage P or R, press selector lever button. Never shift to P or R while the vehicle is moving. The engine can only be started when the selector lever is in position P or N. Depress foot brake or apply hand brake before starting. Transmission display Display of mode or current gear. P Park position. R Reverse gear. N Neutral.
Driving and operation 117 When upshifting in manual mode, take heed of prevailing road conditions, keeping engine speed below the red zone. Downshifts must be made in accordance with vehicle speed. Gears can be skipped by moving the selector lever repeatedly at short intervals. When starting on slippery surfaces, move selector lever forwards to engage 2nd gear. The selected gear is displayed in the transmission display.
Driving and operation Engine braking assistance Automatic mode The automatic transmission automatically selects the driving programs with the best possible braking effect. If necessary, lower gears can also be selected in manual mode to increase the braking effect. 1st gear has the greatest braking effect. Manual mode In order to utilize the engine braking effect when driving downhill, select drive range 3, 2 or, if necessary, 1 in good time.
Driving and operation Parking Before leaving the vehicle: z z z z z z z Depress and hold foot brake, Apply hand brake, Move selector lever to position P, Turn key to LOCK position, Remove ignition key, Engage steering column lock, Lock the vehicle. When the ignition is switched off, the automatic transmission no longer responds to movements of the selector lever.
Driving and operation If the cause of the interruption to the power supply is not a discharged battery, release selector lever: 1. Turn off ignition and remove key. 2. Depress and hold foot brake. 3. Remove cap on console with a suitable screwdriver. 4. Insert ignition key and press gently into shift lock release slot. 5. Shift to neutral (N). 6. Remove key from shift lock release slot. 7. Start engine and shift to chosen gear. 8. Reinstall cap on console.
Driving and operation All Wheel Drive On-road driving The increased traction of All Wheel Drive vehicles offers greater driving control in adverse road conditions, particularly heavy snow and ice. However, All Wheel Drive vehicles are not "skid-proof" and do not decrease stopping distances. All Wheel Drive (AWD) is an active-ondemand system that engages automatically, with no action required by the driver.
Driving and operation Always exercise caution when in slippery conditions (caused by sand, gravel, water, snow or ice on the road), in order to maintain vehicle control. Off-road driving During off-road driving, you will encounter a variety of driving conditions and circumstances too numerous to list here. Use the accelerator to control the vehicle keep brake pedal use to a minimum. Always use good judgement and common sense.
Driving and operation 123 Check the jack and wheel changing tools, and include a board or plate for supporting the jack on soft ground. Carry emergency equipment, i.e. tow rope, spade, first aid kit etc., which may be desirable if you intend entering unfamiliar off-road terrain. A tow rope should be carried, to allow the recovery vehicle to be placed clear of any adverse ground. Your Opel Partner will assist you in assessing any special requirements.
Driving and operation The ground clearance, ramp angle, angle of approach and departure and wading depth need to be considered, especially in hilly conditions and when wading, to prevent the vehicle becoming stuck and possibly damaged. Driving through water Do not exceed the maximum wading depth. Technical data - see page 215. Maintain a steady engine speed, to help prevent water from entering the exhaust system, but do not exceed 5 km/h (3 mph), to avoid splashing the water.
Driving and operation Self-help Recovery and towing When recovering or towing a vehicle off-road, observe the following: z A greater force is required to move a vehicle from or through mud than when on a hard surfaced road. z Attach a tow rope to the towing eye of the vehicle, not to the axle see pages 164, 174. z Where possible, drive both vehicles forward to affect a recovery, using an appropriate gear to avoid wheelspin. z Avoid the use of reverse gear because of possible resultant wheelspin.
Driving and operation Maintenance Certain maintenance operations, e.g. changes of engine oil, oil filter, air cleaner element and brake pads, are required more frequently for severe operating conditions, e.g. driving on unsurfaced roads, during thick dust or mud accumulation, etc. All Wheel Drive summary Do z Check fuel and tyres, water and oil levels before venturing off-road. If the vehicle is driven off-road to a great extent, the chassis will need regular inspection.
Driving and operation Driving hints The first 1000 km (600 miles) Drive your vehicle at various speeds. Do not use full throttle. Never allow the engine to labour at low revs. Make good use of all gears. Depress the accelerator pedal a maximum of around three quarters of the available pedal travel in all gears and drive ranges. Do not drive faster than three quarters of maximum speed. Avoid quick starts, sudden acceleration and prolonged high-speed driving, to avoid engine damage and to conserve fuel.
Driving and operation Switching off the engine If the engine temperature is very high, e.g. after driving in mountainous terrain: allow engine to idle for approx. 2 minutes, in order to prevent heat accumulation. Engine rpm Under all driving conditions, drive in a favourable engine speed range. When you switch off, fans in the engine compartment may continue running for a time, to cool the engine. Warming up Allow engine to warm up while driving. Do not warm it up by letting it run at idling speed.
Driving and operation Save fuel, protect the environment Trend-setting technology When developing and manufacturing your vehicle, Opel used environment-friendly and, in the main, recyclable materials. The production methods used to make your vehicle are likewise environmentallycompatible. Recycling of production wastes keeps the circulation of material closed. Reduction of energy and water requirements also helps to conserve natural resources.
Driving and operation Overrun z The fuel supply is automatically shut off during overrun, e.g. when the vehicle is being driven down long gradients or during braking - see page 128. Tyre pressure z Inadequate tyre pressure, leading to higher road resistance, costs money in two ways; for more fuel and increased tyre wear. z To enable the overrun cut-off to take effect and save fuel, do not accelerate or declutch. z Regular checks (every 14 days) pay off.
Driving and operation Fuels, refuelling Fuel consumption Optional equipment (e.g. wide tyres, towing equipment) increases the kerb weight and, in some cases, also the permissible Gross Vehicle Weight. This in turn increases fuel consumption and reduces the maximum speed of the vehicle. When the vehicle is new, there is increased friction between the engine and transmission components lasting for several thousand kilometres. This also increases fuel consumption.
Driving and operation Fuel filler cap If replacing the fuel filler cap, be sure to use the original fuel filler cap for your model, to ensure full functionality. Correct refuelling is largely dependent on correct operation of the dispensing pump: Refuelling z After the first automatic cut-off, do not fill the tank any further. z Insert dispensing pump as far as it will go and switch it on. 9 Warning Replace the fuel filler cap and turn it clockwise until you hear several clicks.
Driving and operation Damage to the catalytic converter or the vehicle may result if the following points are not observed: z If the engine misfires or runs roughly after a cold start, the engine power has reduced significantly or other unusual operating problems occur that indicate a fault in the ignition system, please contact a workshop as quickly as possible. Drive at a slower speed and with less engine revs for a short time, if necessary.
Driving and operation Controlling exhaust emission Through design-related measures, primarily in the fuel injection and ignition systems (in combination with the catalytic converter), the proportion of noxious materials in the exhaust, such as carbon monoxide (CO), hydrocarbons (CH) and nitrogen oxides (NOx), is reduced to a minimum. Control indicator for exhaust emissions Control indicator Z illuminates for a few seconds when the ignition is switched on.
Driving and operation Exhaust gases 9 Warning Engine exhaust gases contain poisonous carbon monoxide, which has no colour or odour and can be lethal if inhaled. If exhaust fumes penetrate the vehicle interior, open the windows and consult a workshop immediately. Do not run engine in enclosed spaces, e.g. in a garage, or sit in a parked vehicle for an extended period with the engine running. Do not drive with tailgate open.
Driving and operation Drive control systems Electronic Stability Control (ESC) The Electronic Stability Control improves driving stability when necessary, independently of the type of road surface and the tyre grip. It also prevents the drive wheels from spinning. The system monitors vehicle movements. As soon as the vehicle starts to swerve (understeers/oversteers), engine output is reduced (the sound of the engine changes) and individual wheels are specifically braked.
Driving and operation 137 ESC Not Ready control indicator A The control indicator illuminates in yellow for approx. 4 seconds when the ignition is switched on. Switching off Control indicator J illuminates in yellow for approx. 4 seconds when the ignition is switched on. Turn off ESC function to allow engine rpm to increase, by pressing button J. Control indicator J illuminates in the instrument panel. Illuminates to indicate that the system is not ready for conditions to operate.
Driving and operation Hydraulic Brake Assist (HBA) When the ESC function comes into action and recognises any emergency situations requiring hard braking, it automatically delivers increased braking pressure to the wheels. Active Rollover Protection (ARP) If the vehicle moves in an unstable manner, this function helps the vehicle maintain normal stability. Trailer Stability Assist (TSA) 3 TSA monitors vehicle movements when towing a caravan or trailer.
Driving and operation To deactivate Press DCS button again. The green DCS control indicator 5 will extinguish. 139 Flashing or illumination of the yellow DCS control indicator 5 reminds the driver that the friction material needs to cool down: drive the vehicle without braking as much as possible. Depressing the foot brake or accelerator will also cause the DCS function to be deactivated. If the control indicator does not extinguish, have the cause of the fault remedied by a workshop.
Driving and operation Cruise control 3 Cruise control can store and maintain speeds over approx. 30 km/h (20 mph). Deviation from the stored speed may occur when driving uphill or downhill. For safety reasons, cruise control cannot be activated until the foot brake has been depressed once. Cruise control is operated with buttons d, c and e on the turn signal lever. Do not use cruise control if it is not advisable to maintain a constant speed (e.g.
Driving and operation Increase speed With cruise control active, press and hold the c button and release it when the desired vehicle speed is reached. To deactivate Switch off cruise control when not needed, to avoid accidental activation. To increase the speed in steps of 2 km/h (1.2 mph), tap the c button and release it. Control indicator m extinguishes and the vehicle slowly decelerates. To continue driving, depress the accelerator pedal in the usual manner.
Driving and operation The acoustic signal may differ depending on the type of object detected. If the vehicle approaches an obstacle when in a forward gear or while reversing, a series of signals can be heard in the vehicle interior. The interval between the signals becomes shorter as the distance is reduced. If the distance is less than 30 cm, the signal will be continuous.
Driving and operation 143 To ensure the safety of other road users and people in the vicinity and to avoid damage to the vehicle, remember: z The park pilot should only be considered as a supplementary function. Normal precautions should be maintained when reversing. Check the rear view and use the mirrors when reversing. z Do not push, scratch or otherwise damage the sensors. z Do not use high-pressure jet cleaners to clean the sensors. Clean only with a soft sponge and clean water.
Driving and operation Tyre pressure monitoring system 3 The tyre pressure monitoring system continually checks the pressure of all four wheels while driving. A pressure sensor is integrated in each wheel. Once a minute, the pressure of each tyre is sent to a control unit, where it is compared. If the system detects one or more pressure differences, a message appears on the information display. Current tyre pressures can be shown in the information display.
Driving and operation 145 Brake system Ü Board Computer Tyre pressure check rear left (value in bar) OK A graphic indicating the left rear tyre is shown together with the current tyre pressure; slight pressure deviation. Reduce speed. Check pressure at next opportunity with appropriate gauge and correct if necessary. On the colour information display 3, this report will appear in yellow.
Driving and operation Foot brake The brake system comprises two separate brake circuits. If one brake circuit should fail, the vehicle can still be braked with the second remaining circuit. If this happens, the brake pedal must be fully depressed with greater pedal pressure. The distance required for braking will be greater.
Driving and operation 147 If the control indicator stays lit, the brakes do not operate as normal or leaks are found in the brake system, do not attempt to drive the vehicle. Have the vehicle towed to a workshop for inspection and repair. If the control indicator does not illuminate when the ignition is switched on or when the hand brake is applied (with ignition on), stop and consult a workshop. Hand brake Always apply hand brake firmly. On slopes, apply the hand brake as firmly as possible.
Driving and operation Anti-lock Brake System (ABS) u If control indicator u illuminates during driving along with brake system control indicator 4, there is a serious fault in the brake system. Have the system checked immediately by a workshop. The ABS continually monitors the vehicle's brake system and prevents the wheels from locking, irrespective of the road condition and tyre grip. It starts to regulate the braking pressure as soon as a wheel shows a tendency to lock.
Driving and operation Wheels, tyres See page 223 for suitable tyres and restrictions. Factory-fitted tyres are matched to the chassis and offer optimum driving comfort and safety. Changing tyre/wheel type Note the necessary modifications before switching to different tyres or wheels. 9 Warning Use of unsuitable tyres or wheels may lead to accidents and render the vehicle unroadworthy. If wheel rims of a different type are to be installed, the wheel nuts may also need to be changed.
Driving and operation Tyre pressure Check tyre pressures when cold, at least every 14 days and prior to any long journey. Don't forget to check the spare. Use the valve cap key 3 to make unscrewing the valve caps easier. The valve cap key is located on the inside of the tank flap. Tyre pressures - see page 224. Increased pressure resulting from tyre warm-up must not be reduced, otherwise the pressure may drop below the permissible minimum when the tyres cool down.
Driving and operation 151 General information Note that the danger of aquaplaning is greater if the tyres are worn and if the tyre pressures are not correct. Tyres age, even if they are used only very little or not at all. A spare wheel which has not been used for six years should be used only in emergencies: drive slowly when using such tyres. Never fit used tyres the previous history and use of which you do not know. Tread depth Check tread depth regularly.
Driving and operation Tyre designations Meanings: Winter tyres 3 See page 223 for restrictions. e.g. 235/60 R 17 102 H Winter tyres improve safety at extremely low outside temperatures and should therefore be fitted on all wheels. 235 = Tyre width in mm 60 = Aspect ratio (tyre height to tyre width in %) R = Belt type: Radial 17 = Rim diameter in inches 102 = Load index e.g.
Driving and operation Always use fine-linked chains that add no more than 15 mm to the tyre tread and the inboard sides (including chain lock). Temporary spare wheel The temporary spare wheel is designed for use on your vehicle only. Tyre chains may only be used at speeds of up to 50 km/h (30 mph)1) or up to the tyre chain manufacturer’s recommended maximum speed, whichever is lower.
Driving and operation Flex-Fix system 3 The Flex-Fix system allows up to two bicycles to be attached to a pull-out carrier integrated beneath the vehicle floor. The maximum load is 40 kg. If not in use, the Flex-Fix system has to be collapsed back beneath the vehicle floor. There must not be any objects on the bicycles that could become loose during transportation. A multifunction box 3 is offered as an accessory for the carrier system. The transportation of other objects is not permitted.
Driving and operation Pull up license plate holder and fully insert the holder supports into the retainers. Install the tail lamps Remove the left tail lamp (1), then the right tail lamp (2) from the storage bay. 155 Open out the lamp support on the back of the tail lamp all the way.
Driving and operation Push the clamping lever and insert the lamp support into the retainer until it hits the stop. Perform this procedure for both tail lamps. Check the cable and lamp position to make sure these are correctly installed and are securely located. Lock the Flex-Fix system Swivel the left clamping lever (1) outwards first, followed by the right clamping lever (2) until they stop. Both clamping levers must point backwards, otherwise safe functionality is not guaranteed.
Driving and operation Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. Remove the pedal crank mounts from the pedal crank recesses. 157 Adapting the Flex-Fix system to a bicycle With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit all the way (position 5), see illustration.
Driving and operation If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1), see illustration. Press the release lever and withdraw the wheel recesses. Push the release lever on the strap retainer and remove the strap retainer.
Driving and operation Prepare the bicycle for attachment Rotate the left pedal (opposite the chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal. Attaching a bicycle to the Flex-Fix system Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. 159 Insert pedal crank mount into outer rail of each pedal crank recess from above and slide downwards as far as it will go, see Fig. 18454 S on page 160.
Driving and operation Attach the pedal crank by rotating the attachment screw on the pedal crank mount. Place the wheel recesses such that the bicycle is more or less horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Setting the wheel recesses - see page 158. Both bicycle tyres must be in the wheel recesses. In order to prevent damage, neither the pedal bearing housing on the bicycle nor the pedal crank should be touching the pedal crank recess.
Driving and operation Tighten the attachment screw for the pedal bearing mount to its maximum point. Secure both bicycle wheels to wheel recesses using strap retainers. Check the bicycle to make sure it is secure. The settings for the wheel recesses and the rotary lever on the pedal crank recess should be noted and saved for each bicycle. Correct presetting will facilitate refitting of the bicycle. Removing a bicycle from the Flex-Fix system Undo strap retainers on both bicycle tyres.
Driving and operation Secure the strap retainer and pull tightly downwards as far as possible. Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Caution; risk of trapping fingers.
Driving and operation Swivel first the right clamping lever (1), inwards, followed by the left clamping lever (2), until they can be engaged in their respective recesses. Push the clamping lever and pull both lamp supports out of the recesses. 163 Fold in the lamp supports on the backs of the tail lamps. First place the right tail lamp (1), then the left tail lamp (2) in their respective recesses and push down as far as possible. Push cables all the way into all guides in order to prevent damage.
Driving and operation Towing equipment 3 If the vehicle is not equipped with a trailer hitch, we recommend having this retrofitted by a workshop, who will advise you on any possible towed load increases. The workshop has instructions on how to install the trailer hitch and making any changes to the vehicle that are needed that affect the cooling system, heat shields or other equipment. 9 Warning Pull up license plate holder and fold down into horizontal position. Open the tailgate.
Driving and operation 165 Towing equipment with detachable coupling ball bar 3 Stowage of coupling ball bar The coupling ball bar is kept in a bag, fastened with a strap and is stowed below the floor cover in the luggage compartment. Fitting the coupling ball bar Remove sealing plug from the hole for the coupling ball bar and stow it in the luggage compartment. Confirm that the colour marking on the lever is red.
Driving and operation Important Check that the coupling ball bar is correctly attached: z Green marking must be visible on lever. z Coupling ball bar must be seated firmly in coupling housing. Coupling ball bar must be locked and key must be removed. 9 Warning Inserting the coupling ball bar Insert the coupling ball bar into the coupling housing and push firmly downwards until the coupling ball bar audibly engages. If it does not engage, repeat fitting procedure.
Driving and operation Towing Since engine power decreases as altitude increases because of the air becoming thinner, therefore reducing climbing ability, it may not be possible for permissible trailer loads to be fully utilized in mountainous territory. The actual caravan/trailer load is the difference between the actual gross weight of the caravan/trailer and the actual coupling socket load with the caravan/ trailer coupled.
Driving and operation Coupling socket load The coupling socket load is the load exerted by the caravan/trailer on the coupling ball. It can be varied by changing the weight distribution when loading the caravan/trailer. The maximum permissible coupling socket load for the towing vehicle (80 kg) is stated on the towing equipment identification plate and should always be aimed for, particularly in the case of heavy caravans/ trailers. The coupling socket load should never be below 25 kg.
Driving and operation Driving characteristics, towing tips In the case of caravans/trailers with brakes 3, attach the breakaway stopping cable to the eye 3 or loop around coupling ball bar if no eye is available. Ensure cable is crossed under the coupling socket to ensure the caravan/trailer nose cannot drop to the ground if it becomes separated from the trailer hitch. Do not allow the cable to drag along the ground and always allow enough slack to permit full turning.
Driving and operation Block the wheels of both the caravan/trailer and the vehicle when parking and always apply the hand brake firmly. If possible, do not park on slopes. 9 Warning Have someone provide assistance when removing blocks. Always remove blocks from wheels while standing to one side. Do not remove blocks while standing behind the caravan/trailer; risk of injury and damage to both the vehicle and caravan/trailer.
Self-help, vehicle care Self-help, vehicle care Diesel fuel system, bleeding .............. 171 Bonnet ................................................. 171 Starting................................................ 172 Starting the engine with jump leads 3 172 Towing ................................................. 174 Jack and vehicle tools ........................ 176 Warning triangle ¨ 3, 177 First aid kit + 3 ................................ Temporary spare wheel .....................
Self-help, vehicle care Starting Do not start with quick charger This prevents damage to electronic components. 9 Warning If the vehicle battery requires charging whilst still in the vehicle, ensure there is adequate ventilation in and around the battery compartment, to prevent risk of explosion. To open completely, locate the safety catch, found slightly left of centre on the underside of the bonnet, push the catch upwards and lift the bonnet gently. The bonnet is held open automatically.
Self-help, vehicle care 173 z Use auxiliary battery with same voltage (12 volts). Its capacity (Ah) must not be considerably less than that of the discharged battery. Voltage and capacity information can be found on the batteries. z Use jump leads with insulated terminals and a width of at least 16 mm2 (25 mm2 for diesel engines). z Do not disconnect the discharged battery from the vehicle. z Never expose the battery to naked flames or sparks. z Switch off all unnecessary electrical consumers.
Self-help, vehicle care Place gearshift lever in neutral. Switch on the ignition to release the steering column lock and to permit operation of the brake lamps and windscreen wipers. 9 Warning Care must be taken to ensure that the leads do not inadvertently contact metal surfaces within the compartment area. Drive off slowly and avoid jerky movements. Impermissible tractive forces could damage the vehicles. z Do not connect leads to negative terminal of discharged battery.
Self-help, vehicle care Keep tow rope 3 clear of front bumper, and ensure it is securely fixed to the towing eye at both ends. Pull on the tow rope 3 to check. To prevent entry of exhaust fumes from towing vehicle, switch on air recirculation mode (see page 109) and close the windows. Never let passengers ride in a vehicle that is being towed. Never tow a vehicle with damaged parts that are not secured to the vehicle or if wheels, brakes or steering are damaged.
Self-help, vehicle care Screw the rear towing eye attachment anticlockwise until it is firmly in place. 9 Warning Never lift vehicle using the towing eye. Drive off slowly and avoid jerky movements. Impermissible tractive forces could damage the vehicles. To prevent damage, do not take up slack in the tow rope too quickly. After towing, unscrew the rear towing eye attachment clockwise to remove, and reinstall the cover.
Self-help, vehicle care Warning triangle ¨ 3, First aid kit + 3 177 General information If you use winter tyres 3, the spare wheel may still be fitted with a summer tyre. Your first aid kit and warning triangle can be accommodated below the floor cover in the luggage compartment. If you use the spare wheel when it is fitted with a summer tyre, the vehicle's driveability may be affected, especially on slippery road surfaces.
Self-help, vehicle care Notes on temporary spare wheel z Using a temporary spare wheel may change the driving behaviour of the vehicle, particularly if using winter tyres 3. Replace defective tyre as quickly as possible, balance wheel and fit to vehicle. z Fit only one temporary spare wheel. z Do not drive faster than 80 km/h (50 mph). z Take curves slowly. z Do not use the temporary spare wheel for a lengthy period. z Replace temporary spare wheel with full specification wheel without delay.
Self-help, vehicle care z Remove wheel trim 3. z Slacken wheel nuts one turn only before raising the vehicle, but do not totally unscrew or remove the nuts until the wheel is off the ground. z Never change more than one wheel at a time. z Block wheel diagonally opposite the wheel to be changed, by placing wedge blocks or equivalent in front and behind the wheel. z Do not jack-up the vehicle when traffic is too close. z Use jack only when changing wheels. z Never exceed jack maximum working load (900 kg).
Self-help, vehicle care 3. The location of front and rear jacking points is indicated by notches on the bottom edge of the vehicle, under the doors. 4. Before positioning the jack, set it to the necessary height by rotating the eye by hand. Position jack at the front or rear jacking point located nearest to the wheel concerned so that the jack claw spans the vertical base. Make sure it is properly positioned.
Self-help, vehicle care 11. Stow replaced wheel in luggage compartment. 12. Stow the jacking equipment and warning triangle 3 - see pages 176, 177. 13. Check the tyre pressure of the newly fitted wheel - see page 224. Adjust as necessary. 7. Change the wheel. Notes on spare wheel - see page 178. 8. Screw on wheel nuts and tighten slightly by hand until wheel is held against the hub. 9. Rotate wrench anti-clockwise and lower vehicle to the ground. 14.
Self-help, vehicle care Only install fuses of the specified rating. Each fuse has its rating written on it, in addition the fuses are colour coded. Fuses, Colour Grey Light brown Dark brown Red Light blue Yellow White Light green Orange Dark blue When replacing a fuse, turn off the respective switch and the ignition. A defective fuse can be recognized by its melted wire. A new fuse should only be installed after the cause of the trouble has been eliminated.
Self-help, vehicle care Some circuits may be protected by several fuses. No. 1 2 3 4 5 6 7 8 9 10 11 12 Circuit Accessory socket Seat heating Audio Trailer Parking lamp (right side) Air conditioning Power steering Body Control Module Anti-theft alarm Central door locking Turn signal (right side) Turn signal (left side) Rating 20 A 20 A 15 A 10 A 10 A 10 A 10 A 10 A 10 A 20 A 15 A 15 A No.
Self-help, vehicle care Engine compartment fuse box The fuse box is located next to the coolant reservoir in the engine compartment. 9 Warning Switch off engine before opening the engine compartment fuse box; risk of injury. To open, disengage cover and tilt upwards. To help in replacing fuses, a fuse extractor is located in the engine compartment fuse box. Some circuits may be protected by several fuses. No.
Self-help, vehicle care No. 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Circuit Electric seat Battery Defogger Dipped beam (left side) Dipped beam (right side) Parking lamp (left side) Front fog lamps Main beam Rear wipers Headlamp washer Transmission Control Module Trailer/parking lamp (left side) Spare Spare Spare Spare Rating 30 A 60 A 30 A 15 A 15 A 10 A 15 A 15 A 20 A 20 A 15 A 10 A 25 A 20 A 15 A 10 A 185 Bulb replacement Before replacing a bulb, switch off ignition and relevant switch.
Self-help, vehicle care Halogen headlamp system Dipped and main beam Main beam 1 (inner bulbs) and dipped beam 2 (outer bulbs). 1. Remove headlamp assembly see page 185. 2. Remove headlamp cap. 3. Release bulb retaining spring and remove bulb from reflector housing. 4. When fitting a new bulb, ensure the lugs engage correctly with the recesses on the reflector. Do not touch the glass. 5. Engage bulb retaining spring and replace headlamp cap. Parking lamps 1. Remove headlamp assembly see page 185.
Self-help, vehicle care Xenon headlamp system 3 Halogen headlamps A can be identified from Xenon headlamps B by the different lens layout. 9 Warning Xenon headlamps operate at very high voltages. Do not touch; risk of fatal injury. Have dipped beam and main beam repaired by a workshop only. 187 Parking lamps 1. Remove headlamp assembly see page 185. Front turn signal lamps 1. Remove headlamp assembly see page 185. 2. Rotate bulb holder anti-clockwise and withdraw bulb holder from lamp assembly. 2.
Self-help, vehicle care Front fog lamps 1. Remove 2 screws from panel on underside of vehicle below front fog lamps and remove panel. Side repeater lamps 1. Using a suitable screwdriver, pry lamp assembly away from wing. 2. Disconnect harness connector from bulb holder and rotate bulb holder anticlockwise. 3. Remove bulb from lamp assembly by pulling bulb straight out of bulb holder. 3. Remove bulb holder from lamp assembly, rotate bulb anti-clockwise and remove from bulb holder. 4.
Self-help, vehicle care 189 6. Replace lamp assembly by guiding lugs on lamp assembly into their holes (see black arrows in illustration). License plate lamps 1. Remove 4 screws (arrowed) and remove lamp covers. Front reading lamps 1. Using a suitable screwdriver, pry lamp lens away from roof lining. 7. Replace 2 screws removed earlier and close the tailgate. 2. Remove bulb holder from lamp assembly by rotating it anti-clockwise. 2. Remove bulb. 3. Pull bulb straight out of bulb holder. 4.
Self-help, vehicle care Rear interior lamps 1. Using a suitable screwdriver, pry lamp lens away from roof lining. Luggage compartment lamps 3 1. Using a suitable screwdriver, remove lens from lamp assembly. Front door lamps 1. Using a suitable screwdriver, pry lamp lens away from front door trim. 2. Remove bulb. 2. Remove bulb. 2. Remove bulb. 3. Install new bulb. 3. Install new bulb. 3. Install new bulb. 4. Reinstall lamp lens in roof lining. 4. Reinstall lens to lamp assembly. 4.
Self-help, vehicle care Centre high-mounted stop lamp, instrument panel and glove compartment illumination We recommend having bulb replacements carried out by a workshop. Never carry out any repairs or adjustment and maintenance work on the vehicle yourself. This especially applies to the engine, chassis and safety parts. You may, out of ignorance, infringe the provisions of the law and, by not performing the work properly, you may endanger yourself and other road users.
Self-help, vehicle care Engine oil Information on engine oils - see page 213. Engine oil level and consumption It is normal for every engine to consume some oil, and it is sometimes necessary to check and top up the engine oil level between oil changes. 9 Warning Do not allow the engine oil level to drop below the minimum level. For this reason, the engine oil level should be checked every 500 km (300 miles) or before starting a long trip.
Self-help, vehicle care Top up if the engine oil level has dropped to the "add oil" lower mark (or MIN mark). The oil level must not go above the upper (or MAX) mark on the dipstick. This would lead, for example, to increased oil consumption, excessive formation of carbon residue and a possible risk of damage to the catalytic converter or the engine. When replenishing, attempt to use the same type of engine oil as used at the last oil change. 193 Capacities - see page 225.
Self-help, vehicle care 9 Warning Used engine oil filters and empty oil containers should not be disposed of as domestic refuse. We recommend that you entrust oil and oil filter changes to a workshop who is familiar with legal requirements regarding disposal of used oil and can thus help to protect both the environment and your health. Engine oil is a danger to health; avoid prolonged contact with skin and wash exposed areas thoroughly.
Self-help, vehicle care Check diesel fuel filter at shorter intervals if the vehicle is subjected to extreme operating conditions such as high humidity (primarily in coastal areas), extremely high or low outside temperatures and substantially varying daytime and nighttime temperatures. If there is water in the diesel fuel filter, control indicator N illuminates in the instrument panel - see page 73. Drain the water immediately. 195 Coolant During operation, the system is pressurized.
Self-help, vehicle care 9 Warning Allow engine to cool down before removing coolant filler cap. If steam is visible, move away from the vehicle until the engine is cool. Remove coolant filler cap carefully so that pressure can escape slowly, otherwise there is a risk of scalding. When the engine is at operating temperature, coolant level rises. It falls again when the system cools. If it falls below the MIN mark when the system is cold, the coolant must be replenished. Top up antifreeze.
Self-help, vehicle care The brake fluid level in the reservoir must not be higher than the MAX mark or lower than the MIN mark. Do not overfill the brake fluid reservoir, as this may cause an engine fire due to fluid burning; risk of injury and damage to the vehicle. Use of some brake fluids could cause damage or impair braking effectiveness. Stay well informed. We recommend that you use Opel-approved high performance brake fluid.
Self-help, vehicle care Windscreen wipers Clear vision is essential for safe driving. Perform regular checks on the wipers to ensure they are operating correctly. We recommend wiper blade replacement at least once a year. If the windscreen is dirty, operate the windscreen washer system before switching on the wipers or setting the wipers to automatic operation with the rain sensor 3. This will avoid wiper blade wear.
Self-help, vehicle care 199 In cold weather, do not fill the windscreen washer fluid reservoir more than threequarters full, to allow enough room for expansion if the fluid freezes, and to prevent damage to the reservoir. In freezing conditions, use windscreen washer fluid with sufficient antifreezing properties. Do not use coolant antifreeze or tap water, to avoid freezing the solution and damaging the windscreen washer system. When closing the container, press the lid down firmly all the way round.
Self-help, vehicle care Laying up the vehicle for more than 6 weeks can lead to battery discharge, which may reduce the service life of the battery. Disconnect battery from on-board power supply by detaching negative terminal (anti-theft alarm system 3 is then disabled). Ensure that ignition is switched off before connecting the battery. Then perform the following actions: z Set date and time in the information display - see pages 80, 86. Battery The battery is maintenance-free.
Self-help, vehicle care Disconnecting/connecting the battery from/to the electrical system Disconnect the battery from the vehicle electrical system before charging: first detach the negative and then the positive lead. Do not reverse the polarity of the battery, i.e. do not confuse the terminals for the positive and negative leads. When connecting, start with the positive lead and then connect the negative lead.
Self-help, vehicle care Vehicle care aids 3 Vehicle wash: z Car Shampoo z Sponges z Chamois Leather z Wheel Cleaners z Engine Cleaners z Glass Cleaners Washing The paintwork of your vehicle is exposed to environmental influences, e.g. continuous changes in weather conditions, industrial waste gases and dust or thawing salts, so wash and wax your vehicle regularly. When using automatic car washes, select a program which includes waxing.
Self-help, vehicle care Waxing Wax your vehicle regularly, in particular after it has been washed using Car Shampoo and at the latest when water no longer forms beads on the paintwork, otherwise the paintwork will dry out. Also wax aluminium trim parts, edges and folds on opened doors and flaps as well as the areas they cover. Polishing Polishing is necessary only if the paint has become dull or if solid deposits have become attached to it.
Self-help, vehicle care Plastic and rubber parts For additional cleaning of plastic and rubber parts, use a cleaner suitable for vehicle interiors. Do not use any other agent, and in particular do not use solvents or petrol. Wheels and tyres Do not use high-pressure jet cleaners on wheels and tyres. Interior and upholstery Clean the vehicle interior regularly, including the instrument panel fascia, using Interior/Upholstery Cleaner. Clean fabric upholstery with a vacuum cleaner and brush.
Self-help, vehicle care Windscreen wiper blades Wax, such as that used in car washes, can cause streaks to form on the windscreen when the wipers are used. Smearing wiper blades can be cleaned with a soft cloth and Opel Cleaning Solvent and Antifreeze, and replaced if necessary – see page 198. Do not use abrasive cleaners. Locks The locks are lubricated with a high-grade lock cylinder grease at the factory. Opel Lock Cylinder Grease prevents the locks from freezing up.
Service, maintenance Service, maintenance European service schedule ................ International service schedule ........... Additional servicing............................ Recommended fluids and lubricants 207 209 213 213 European service intervals Confirmations Engine oil change - Z 24 XE only Due every 15,000 km (10,000 miles). Confirmation of Service is recorded in the spaces provided in the Service and Warranty Booklet.
Service, maintenance 207 European service schedule (Antara Z 20 DM, Z 20 DMH, Z 24 XE, Z 32 SE) by year 1) km ( x 1000)1) miles ( x 1000)1) Controls, lighting, signalling equipment and airbags: visual check steering lock and ignition lock: check Remote control batteries: replace Service operations 15 10 1 30 20 x 2 60 40 x 75 50 3 90 60 x Every 2 years Windscreen wipers, windscreen washer system: check, correct x x x Coolant level and antifreeze: check, correct Hoses: check for tightness and se
Service, maintenance Service operations by year 1) km ( x 1000)1) miles ( x 1000)1) ⊕ Diesel fuel filter: drain water o (If relative humidity is high and/or fuel is of lower quality) Fuel filter: replace and drain water - diesel (grade EN 590) 15 10 1 30 20 2 45 60 30 40 Annually 75 50 3 90 60 Every 2 years/60 000 km/40 000 miles Parking brake: check and adjust Wheel mounting and suspension front and rear, brake lines, brake pressure hoses, fuel lines and exhaust system: visual check Corrosio
Service, maintenance 209 International service schedule (All except Z 24 XE) by year 1) km ( x 1000)1) miles ( x 1000)1) Controls, lighting, signalling equipment and airbags: visual check steering lock and ignition lock: check Remote control batteries: replace Service operations Windscreen wipers, windscreen washer system: check, correct 15 10 x 1 30 20 x 2 60 40 x x x x 3 90 60 x x x x Annually x x Battery terminals: check for secure connections and battery eye Annually Vehicle system che
Service, maintenance Service operations by year 1) km ( x 1000)1) miles ( x 1000)1) 15 10 ⊕ Diesel fuel filter: drain water o (If relative humidity is high and/or fuel is of lower quality) Fuel filter: replace and drain water - diesel (grade EN 590) 1 30 20 2 45 60 30 40 Annually 75 50 3 90 60 Every 2 years/60 000 km/40 000 miles Parking brake: check and adjust Wheel mounting and suspension front and rear, brake lines, brake pressure hoses, fuel lines and exhaust system: visual check Corrosio
Service, maintenance 211 International service schedule (Antara Z 24 XE) by month 1) km ( x 1000)1) miles ( x 1000)1) Controls, lighting, signalling equipment and airbags: visual check steering lock and ignition lock: check Remote control batteries: replace Service operations 6 10 6.5 12 20 13 x 24 40 26.
Service, maintenance Service operations by month 1) km ( x 1000)1) miles ( x 1000)1) Parking brake: check and adjust Wheel mounting and suspension front and rear, brake lines, brake pressure hoses, fuel lines and exhaust system: visual check Corrosion protection: check and record in Service and Warranty Booklet Front and rear wheel brakes: check visually 6 10 6.5 12 20 13 x 18 30 20 24 40 26.
Service, maintenance Additional servicing Additional operations ⊕ Additional work is work that is not required every service but can be performed in conjunction with a regular service. Time allowances for such work are not included in the scope of regular services and will be charged for additionally. It is more economic if these operations are performed as part of a scheduled service than having them performed separately.
Service, maintenance Brake and clutch fluid Not every engine oil available on the market meets the quality requirements, always check the required specification and rating is marked on the container. Only use DOT4 brake fluid. 9 Warning If engine oil of the required quality is not available, a maximum of 1 litre of ACEA A3/B4 or A3/B3 grade may be used (only once between each oil change). The viscosity should be of the correct rating.
Technical data 215 Technical data Vehicle documents, identification plate........................... Coolant, brake fluid, oils .................... Engine data......................................... Performance........................................ Fuel consumption, CO2 emissions ..... 215 216 217 218 219 221 223 225 225 226 Weights, payload and roof load ....... Tyres .................................................... Electrical system ................................. Capacities ..............
Technical data Coolant, brake fluid, oils Use approved fluids only. Use of unsuitable fluids could cause serious damage to the vehicle. Engine oils Information on engine oils is available on page 213. The Vehicle Identification Number (VIN) is also engraved on the top right-hand side of the bulkhead near the centre of the engine firewall.
Technical data 217 Engine data Sales designation Engine stamp Engine identifier code 2.4 Petrol Z 24 SE Z 24 XE 3.2 V6 Petrol 10 HM Z 32 SE 2.0 Diesel Z 20 S Z 20 DMH 2.0 Diesel Z 20 S Z 20 DM Number of cylinders 4 6 4 4 Bore dia. (mm) 87.5 89.0 83.0 83.0 100.0 85.6 92.0 92.0 Piston displacement (cm ) 2405 3195 1991 1991 Max. engine power (kW) at rpm 103 5200 167 6600 110 4000 93 4000 Torque (Nm) at rpm 220 2400 297 3200 320 2000 295 2000 Compression ratio 9.6 10.3 17.
Technical data Performance (approx. km/h / mph) Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM 175/109 - 203/126 180/112 178/111 174/108 - 2) Maximum speed Manual transmission Automatic transmission 1) 2) Sales designation - see page 217. The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
Technical data Fuel consumption, CO2 emissions Directive 80/1268/EEC (last changed by 2004/3/EG) has applied for the measurement of fuel consumption since 1996. The directive is oriented to actual driving practices: Urban driving is rated at approx. 1/3 and extra-urban driving with approx. 2/3 (urban and extra-urban consumption). Cold starts and acceleration phases are also taken into consideration. The specification of CO2 emission is also a constituent of the directive.
Technical data Fuel consumption (approx. l/100 km), CO2 emission (approx. g/km) Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Manual transmission/Automatic transmission urban extra-urban total CO2 13.3/7.3/ 9.6/ 229/- - /16.4 - / 8.9 - /11.6 - /278 8.7/10.9 6.8/ 7.3 7.6/ 8.6 198/238 8.8/6.7/7.5/200/- 1) Sales designation – see page 217.
Technical data Weights, payload and roof load The payload is the difference between the permissible Gross Vehicle Weight (see vehicle identification plate on page 215) and the EC kerb weight. To calculate the EC kerb weight, enter the data from your vehicle below: z Kerb weight from + ............. kg page 222 z Weight of heavy + ............. kg accessories The total 221 The combined total of front and rear axle loads must not exceed the permissible Gross Vehicle Weight.
Technical data Weights (kg), Kerb weights Model Engine1) Kerb weight2)3) Manual transmission Kerb weight3) Automatic transmission Enjoy/Edition Z 24 XE 1805 - Z 32 SE - 1845 Z 20 DMH 1845 1865 Z 20 DM 1845 - Z 24 XE 1805 - Z 32 SE - 1845 Z 20 DMH 1845 1865 Z 20 DM 1845 - Cosmo 1) 2) 3) Sales designation - see page 217. The Gross Train Weight (GTW), along with the Gross Vehicle Weight (GVW) are shown on the VIN plate - see page 215.
Technical data Tyres Tyre chains Wheels Restrictions Not all tyres available on the market currently meet the structural requirements. We recommend that you consult an Opel Partner concerning suitable tyre makes. Restrictions We recommend the use of Opel-tested fine-mesh tyre chains that add no more than 15 mm to the tyre tread and the inboard sides (including chain lock). Wheel nut tightening torque: 125 Nm.
Technical data Tyre pressures in kPa/bar The tyre pressures given are valid for cold tyres. The increased tyre pressure resulting from extensive driving must not be reduced. The tyre pressures specified apply to both summer and winter tyres. Always inflate the spare wheel to the tyre pressure for full load. Further information - see pages 149 to 153.
Technical data 225 Electrical system Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Voltage 12 V 12 V 12 V 12 V Amp hours 60 Ah 70 Ah 90 Ah 90 Ah CR 2032 or equivalent CR 2032 or equivalent CR 2032 or equivalent CR 2032 or equivalent Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Engine coolant 9.0 10.0 9.0 9.0 Fuel tank 65 65 65 65 Engine oil with filter change 4.7 7.4 6.2 6.2 Engine oil between MIN and MAX on dipstick 1.0 1.0 1.0 1.
Technical data Dimensions Overall length (mm) 4576 Width (mm) 1850 Overall height with roof rails (mm) 1747 Wheelbase (mm) 2707 Track width (mm): Front Rear 1562 1572 Turning circle diameter, wall to wall (m) 12.78 Maximum wading depth (mm) (at 5 km/h (3 mph)) 450 Approach angle 24° Ramp angle 17.
Technical data 227 Mounting dimensions of caravan/ trailer towing equipment Dimension A B C D E F (fully laden) G (at kerb weight) mm 416 507 482 734 1039 353 446 9 Warning Only use towing equipment approved for your vehicle. We recommend entrusting fitting of towing equipment at a later date to a workshop.
Index Index A ABS ......................................................... 148 Accessories ......... 45, 57, 69, 169, 191, 200 Accessory sockets ................................... 69 Active Rollover Protection (ARP) .......... 138 Air conditioning system ................ 103, 109 Air distribution ....................................... 106 Air intake ............................................... 114 Air quality sensor .................................. 112 Air recirculation mode .................
Index Brakes ..................................................... 145 ABS ..................................................... 148 Brake assist ........................................ 146 Brake fluid .......................................... 196 Brake lamps ....................................... 188 Brake servo unit ................................. 127 Foot brake .......................................... 146 Hand brake ........................................ 147 Bulb replacement ....................
Index D Dashboard - see Instrument panel ........ 10 Data .................................................21, 215 Date .......................................................... 80 Daytime running lamps .......................... 94 DCS (Descent Control System) ............. 138 Demisting and defrosting Windows ............................................... 17 With air conditioning system ............ 108 With Electronic Climate Control ....... 113 Descent Control System ........................
Index Fuel gauge ............................................... 76 Fuel system, diesel ................................ 194 Fuse extractor ........................................ 182 Fuses ....................................................... 181 G Gears ........................................................ 17 Generator, see Alternator ....................... 74 Glasses compartment ............................. 65 Glove compartment ................................ 64 Bulb replacement ...............
Index K Key ............................................................ 21 Extending ............................................. 21 Ignition lock .......................................... 13 Locking doors ................................27, 28 Removing ............................................. 92 Replacement keys ............................... 21 Starting ...........................................13, 19 Kickdown ........................................117, 118 L Language selection .........
Index Power steering .................................73, 127 Fluid .................................................... 198 Preheating .........................................19, 73 Pushing, towing ..................................... 172 R Radio ...................................................... 101 Radio equipment (CB) .......................... 102 Radio frequency remote control Central locking system ..............6, 23, 25 Fault .....................................................
Index Tank Fuel gauge ........................................... 76 Technical data ....................................... 215 Telephone, see Mobile telephones ...... 102 Temperature regulation ...............106, 112 Temporary spare wheel ................153, 177 The first 1000 km ................................... 127 Tightening torque ................................. 223 Time ....................................................80, 85 Tools .......................................................
