Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 32 Storage ........................................ 52 Instruments and controls ............. 70 Lighting ...................................... 102 Infotainment system ................... 111 Climate control ........................... 113 Driving and operating ................. 119 Vehicle care ..........
Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". We wish you many hours of pleasurable driving.
Introduction 5
In brief In brief Vehicle unlocking Seat adjustment Seat positioning Initial drive information Press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, operate button above number plate. Radio remote control 3 18, Central locking system 3 20, Load compartment 3 22. Pull handle, slide seat, release handle. Seat position 3 33, Seat adjustment 3 34.
In brief Seat backrests Seat height Power seat adjustment Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it. Seat position 3 33, Seat adjustment 3 34. Lever pumping motion up = seat higher down = seat lower Operate switches. Seat position 3 33, Seat adjustment 3 34.
In brief Positioning = move front switch forwards/backwards Height of = move front part of front part of front switch seat upwards/ downwards Height of = move rear part of rear part of front switch seat upwards/ downwards Height of = move entire front entire seat switch upwards/ downwards Backrest = move upper part of rear switch forwards/backwards Seat position 3 33, Power seat adjustment 3 35. Head restraint adjustment Seat belt Press release button, adjust height and engage. Head restraints 3 32.
In brief Mirror adjustment 9 Exterior mirrors Steering wheel adjustment Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 26, Electric adjustment 3 26, Folding exterior mirrors 3 27, Heated exterior mirrors 3 27, Automatic anti-dazzle exterior mirrors 3 28. Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released.
In brief
In brief Instrument panel overview 1 2 3 4 5 6 7 8 Side air vents ..................... 117 Fixed air vents .................... 117 High beam .......................... 103 Headlight flash ................... 103 Turn and lane-change signals ................................ 105 Exit lighting ......................... 109 Parking lights ..................... 106 Cruise control ....................... 87 Remote control on steering wheel ...................... 70 Trip computer .......................
In brief Exterior lighting Turn light switch AUTO = Automatic light control: Headlights are switched on and off automatically. = Off (or deactivation of 7 automatic light control) = Sidelights 8 = Headlights 9 Press button > = Front fog lights r = Rear fog light Lighting 3 102. Headlight flash, high beam and low beam headlight flash high beam low beam = pull lever = push lever = pull lever back towards steering wheel Automatic light control 3 102, High beam 3 103, Headlight flash 3 103.
In brief Hazard warning flashers Horn Washer and wiper systems Windscreen wiper Operated with the ¨ button. Hazard warning flashers 3 104. 13 Press j. & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 71, Wiper blade replacement 3 152.
In brief Windscreen and headlight washer systems Rear window wiper and washer system Pull lever. Windscreen and headlight washer system 3 71, Washer fluid 3 149. Wiper on = push lever Wiper off = pull lever Wash = press and hold button Rear window wiper and washer system 3 73, Wiper blade replacement 3 152, Washer fluid 3 149. Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the Ü button. Heated rear window 3 30, Heated exterior mirrors 3 27.
In brief Demisting and defrosting the windows Air distribution to l. Cooling n and air recirculation 4 are switched on automatically to improve defrosting efficiency. Set temperature to highest level. Set fan speed to highest level. Switch on heated rear window Ü. Close centre air vents, open side air vents and direct them towards the door windows. Climate control system 3 113.
In brief Starting off Starting the engine Parking ■ Turn key to position ACC ■ move the steering wheel slightly to release the steering wheel lock ■ manual transmission in neutral ■ operate clutch and brake pedals ■ automatic transmission in P or N ■ do not accelerate ■ diesel engines: turn key to ON for preheating and wait until control indicator ! extinguishes ■ turn key to START and release Starting the engine 3 120. ■ Always apply the electrical parking brake. Pull switch m.
In brief off the ignition. Turn the front wheels towards the kerb. ■ Lock the vehicle with button p on the radio remote control 3 20 and activate the anti-theft alarm system 3 23. ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Close windows and sunroof. ■ Switch off exterior lights, otherwise the headlight warning device will sound when the driver's door is opened.
Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 22 Vehicle security ............................ 23 Exterior mirrors ............................ 26 Interior mirrors ............................. 28 Windows ...................................... 29 Roof ............................................. 31 Keys, locks Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag.
Keys, doors and windows Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system The radio remote control has a range of approx. 6 metres. This range can be affected by outside influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation. ■ Overload of the central locking system by operating at frequent intervals, the power supply is interrupted for a short time.
Keys, doors and windows Central locking system Unlocks and locks doors, load compartment and fuel filler flap. Note In the event of an accident of a certain severity, the vehicle unlocks automatically. Unlocking Note If no door is opened within 5 minutes after the vehicle has been unlocked, the vehicle is relocked automatically (and the anti-theft alarm is reactivated). When button q is pressed, the instrument panel illuminates for approx.
Keys, doors and windows With the engine running, the tailgate will only unlock when the electrical parking brake is applied or automatic transmission is in position P. Central locking buttons Locks or unlocks all doors, the load compartment and fuel filler flap from the passenger compartment. Fault in radio remote control system Unlocking Manually unlock the driver's door by turning the key in the lock.
Keys, doors and windows Doors Load compartment Tailgate Opening Caution Closing Ensure there are no obstructions and that there is adequate clearance when opening the tailgate. 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, which can not be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Operate the button above the number plate and lift the tailgate.
Keys, doors and windows Fault Vehicle security 23 Activating Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. To open the tailgate in the event of power interruption: Remove the interior trim cover from the central latch area, then push the lever using a suitable tool. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated.
Keys, doors and windows ■ Siren power supply ■ Ignition Activation Ensure the doors, tailgate, fuel filler flap, bonnet, windows and sunroof are closed. Press button p on radio remote control or manually lock the driver's door.
Keys, doors and windows 3. Close doors. 4. Activate the anti-theft alarm system. Press button o again to cancel. Control indicator o extinguishes. Status LED Status during the first 30 seconds of anti-theft alarm system activation: LED = test, arming delay. illuminates LED flashes = doors, tailgate or quickly bonnet not completely closed, or system fault. Status after system is armed: LED flashes = system is slowly armed. LED flashes = system is quickly 3 times disarmed.
Keys, doors and windows Immobiliser The system is integrated into the ignition switch and checks whether the vehicle is allowed to start with the key being used. If the transponder in the key is recognized, the engine can be started. The electronic immobiliser is activated automatically after the key has been removed from the ignition switch. Control indicator d illuminates in the instrument cluster when the ignition is switched on, then extinguishes.
Keys, doors and windows 27 Folding Electric folding Heated For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. With ignition switch in positions ACC or ON, press button n and both exterior mirrors will fold in. Press button n again - both exterior mirrors return to their original position.
Keys, doors and windows Do not use sharp instruments or abrasive cleaners on the exterior mirrors and avoid scratching or damaging the heating elements. Interior mirrors Automatic anti-dazzle Manual anti-dazzle Automatic dimming To reduce dazzle, adjust the lever on the underside of the mirror housing. Exterior mirrors dim to reduce glare automatically in conjunction with the automatic anti-dazzle interior mirror 3 28.
Keys, doors and windows Windows Manual windows After switching off the ignition, window operation is disabled when the driver's door is opened. The door windows can be opened or closed with the window winders. If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again. 9 Warning Power windows can be operated: ■ with ignition on, ■ within 10 minutes of switching ignition off.
Keys, doors and windows Child safety system for rear windows Heated rear window Do not use sharp instruments or abrasive cleaners on the rear window and avoid scratching or damaging the heating elements. Sun visors Press switch z to deactivate rear door power windows. To reactivate, press z again. With the child safety system on, rear door windows can only be operated via the switches in the driver's door.
Keys, doors and windows Roof For incremental operation, briefly press the switch in the required direction. For automatic opening or closing, press and hold the switch. Sunroof 9 Warning Take care when operating the sunroof. Risk of injury, particularly to children. Keep a close watch on the movable parts when operating them. Ensure that nothing becomes trapped in them as they move.
Seats, restraints Seats, restraints Head restraints ............................ 32 Front seats ................................... 33 Rear seats ................................... 37 Seat belts ..................................... 39 Airbag system .............................. 42 Child restraints ............................. 46 Head restraints Height adjustment Position 9 Warning Only drive with the head restraint set to the proper position.
Seats, restraints Stow head restraints securely in load compartment. Active head restraints on front seats In the event of a rear-end impact, the active head restraints automatically tilt forwards. The head is more effectively supported by the head restraint and the risk of whiplash injury is reduced. Do not attach objects or components that are not approved for your vehicle to the head restraints.
Seats, restraints Seat adjustment 9 Danger Pull handle, slide seat, release handle. Seat height Seat backrests Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it.
Seats, restraints Lumbar support Seat folding 35 Folding the backrest forwards is possible only when the backrest is in an upright position. Do not operate lever to adjust lumbar support with backrest tilted forward. Power seat adjustment 9 Warning Adjust lumbar support to suit personal requirements using the lever. To increase or decrease lumbar support, move lever forwards or backwards. Push head restraint all the way down. Slide seat as far back as it will go.
Seats, restraints Seat backrests Armrest Front armrest Seat positioning Move front switch forwards/ backwards. Seat height Move front of switch upwards/ downwards to adjust height of front part of seat cushion. Move rear of switch upwards/ downwards to adjust height of rear part of seat cushion. Move front and rear of switch upwards/downwards to adjust height of entire seat cushion. Move upper part of rear switch forwards/backwards.
Seats, restraints Heating Adjust heating to the desired setting by pressing the ß button for the respective seat one or more times with the ignition switch set to ACC or ON. The control indicator in the button indicates the setting. To deactivate heating, set the heating level to its lowest setting and press the ß button. The control indicator in the button will extinguish. Prolonged use of the highest setting for people with sensitive skin is not recommended.
Seats, restraints 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat folding Push head restraints all the way down, lift backrest release lever and fold backrest forwards and down onto seat cushion. Do not allow passengers to sit on a folded backrest, or place any unrestrained loads on it. To move backrest to its original position, lift and push the backrest into place and ensure the backrest engages. Safety net 3 67.
Seats, restraints Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the seated position. Thereby the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. Seat belts are designed to be used by only one person at a time. They are not suitable for people smaller than 150 cm.
Seats, restraints Three-point seat belt Height adjustment Fastening Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt. Seat belt reminder X 3 81. Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body.
Seats, restraints Removing Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving. To release belt, press red button on belt buckle. 41 Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen.
Seats, restraints Front passenger seat belt reminder Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning When the engine is running, control indicator k flashes then illuminates if the passenger seat is occupied and the seat belt is not engaged.
Seats, restraints 43 Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The warning label reminds that the use of rear-facing child restraint systems on the front passenger seat is not permitted. Risk of fatal injury. The front airbag system is triggered in the event of a front-end impact of a certain severity and functions independently of the side airbag system and curtain airbag system. The ignition needs to be switched on.
Seats, restraints Curtain airbag system The inflated airbags cushion the impact, thereby considerably reducing the risk of injury to the upper body and pelvis in the event of a sideon collision. 9 Warning Keep the area in which the airbag inflates clear of obstructions. Note Only use protective seat covers that have been approved for the vehicle. Be careful not to cover the airbags. The curtain airbag system consists of an airbag in the roof frame on each side.
Seats, restraints The front passenger airbag system can be deactivated via a keyoperated switch on the right side of the instrument panel. Use the ignition key to choose the position: = front passenger airbag * OFF systems are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously on the passenger side of the instrument panel. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 48.
Seats, restraints no person is allowed to occupy the front passenger seat. Contact a workshop immediately. Consult a workshop immediately if neither of the two control indicators is illuminated. Change status only when the vehicle is stopped with the ignition off. Status remains until the next change. Control indicators V and * for front passenger airbag 3 78. Child restraints Child restraint systems We recommend the Opel child restraint system which is tailored specifically to the vehicle.
Seats, restraints Ensure that the child restraint system to be installed is compatible with the vehicle type. Ensure that the mounting location of the child restraint system within the vehicle is correct. Allow children to enter and exit the vehicle only on the side facing away from the traffic. When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle.
Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system On front passenger seat Weight and age class activated airbag deactivated airbag On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months X U1 U, < X Group 0+: up to 13 kg or approx. 2 years X U1 U, < X Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U, < X Group II: 15 to 25 kg or approx.
Seats, restraints 49 Permissible options for fitting an ISOFIX child restraint system On front passenger seat On rear On rear outboard seats centre seat Weight and age class Size class Fixture Group 0: up to 10 kg or approx. 10 months E ISO/R1 X IL X Group 0+: up to 13 kg or approx. 2 years E ISO/R1 X IL X D ISO/R2 X IL X C ISO/R3 X IL X Group I: 9 to 18 kg or approx.
Seats, restraints ISOFIX size class and seat device A - ISO/F3 B - ISO/F2 B1 - ISO/F2X C - ISO/R3 D - ISO/R2 E - ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Permitted installation positions for specific vehicle ISOFIX child restraint systems are marked in the table by IL. No more than two ISOFIX child restraint systems can be installed on the rear seats at the same time, though not on the rear centre seat. ISOFIX mounting brackets are indicated by a label on the backrest.
Storage Storage Storage compartments Glovebox Storage compartments ................ 52 Load compartment ....................... 64 Roof rack system ......................... 68 Loading information ..................... 68 Lockable glovebox Lock and unlock the glovebox with the key. Cupholders Cupholders are located in the front of the centre console. The cupholder is flexible, allowing different size drink containers to be stored. Additional cupholders are located in the centre rear seat armrest.
Storage Front storage 53 Coin storage Sunglasses storage Pull handle to open. Push door firmly to close. To open: push the rear part of the cover. To close: pull up cover and push it until it latches into place. Do not use for storing heavy objects. Console net Located in the front passenger foot well. Card holder Located above the coin storage compartment. A card can be retained in the slot for convenient use.
Storage Underseat storage Armrest storage Front passenger seat undertray Console box in front armrest Pull up on front of tray then pull it forwards. Push the tray towards the seat to return it to its original position. To open: pull up lower lever and lift the lid. To close: lower lid and push it down until it latches into position. To use the tray: ensure armrest is in its rearmost position, pull up on upper lever and lift the lid. Centre console storage Located in rear of centre console.
Storage Rear carrier system 55 There must not be any objects on the bicycles that could become loose during transportation. Caution Do not attach bicycles with carbon pedal cranks to bicycle carriers. The bicycles might get damaged. Extending Open the tailgate. The rear carrier system (Flex-Fix system) allows up to two bicycles to be attached to a pull-out carrier integrated into the vehicle floor. The maximum load is 40 kg. The maximum load per bicycle is 20 kg.
Storage Completely pull out the rear carrier system until it engages. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again. Pull up license plate holder and fully insert the holder supports into the retainers. Install the tail lamps 9 Warning It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged.
Storage Push the clamping lever and push the bulb holder into the retainer until it hits the stop. Perform this procedure for both tail lamps. Check the cable and lamp position to make sure these are correctly installed and are securely located. 57 Lock the rear carrier system Unfold pedal crank recesses Swivel the left clamping lever (1) back first, followed by the right clamping lever (2) until they stop. Both clamping levers must point backwards, otherwise safe functionality is not guaranteed.
Storage Adapting the rear carrier system to a bicycle Remove the pedal crank mounts from the pedal crank recesses. With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit completely (position 5). If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1).
Storage Press the release lever and withdraw the wheel recesses. Push the release lever on the strap retainer and remove the strap retainer. Prepare the bicycle for attachment Note The maximum width for the pedal crank is 38,3 mm and the maximum depth is 14,4 mm. Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal. The front bicycle must have its front wheel facing left. The rear bicycle must have its front wheel facing right.
Storage Attach the pedal crank by rotating the attachment screw on the pedal crank mount. Insert pedal crank mount into outer rail of each pedal crank recess from above and slide downwards as far as it will go. Place the wheel recesses such that the bicycle is more or less horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses.
Storage Tighten the attachment screw for the pedal bearing mount to its maximum point by hand. Secure both bicycle wheels to wheel recesses using strap retainers. Check the bicycle to make sure it is secure. The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle. Correct presetting will facilitate refitting of the bicycle.
Storage Press release lever and slide in wheel recesses all the way as far as they will go. Insert the strap retainer and pull tightly downwards as far as possible. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching. Swivel first the right clamping lever (1) forwards, followed by the left clamping lever (2), until they can be engaged in their respective recesses.
Storage Push the clamping lever and pull both lamp supports out of the recesses. 63 Raise the release lever up and push the system into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop. Pull up license plate holder and fold down into horizontal position. Fold in the bulb holders on the backs of the tail lamps.
Storage Load compartment Closing the cover Removing the cover Pull load compartment cover towards rear of vehicle using handle and insert retainers into brackets on either side of load compartment. Open load compartment cover. Pull socket on either side of cover towards centre of vehicle, lift and remove cover from the side guides. Fit in reverse order. Storage compartments in the load compartment Located on both sides of the load compartment floor.
Storage Rear floor storage cover To access the rear floor storage compartment, push both levers on the floor cover towards the handle and pull up the cover by the handle. 65 Lashing eyes Hang the hook to the upper part of the tailgate opening. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. Jack and vehicle tools 3 166. Tyre repair kit 3 172. Temporary spare wheel 3 177.
Storage Cargo management system Variable partition net The FlexOrganizer is a flexible system for dividing the load compartment or securing loads. The system consists of: ■ adapters, ■ variable partition net, ■ mesh pockets, ■ hooks. The components are fitted in two guide rails in the side walls of the load compartment using adapters and hooks. To remove, press the net rod together and remove from the adapters.
Storage Safety net The safety net can be mounted behind the rear seats or, if the rear seat backrests are folded down, in front of the rear seats. Passengers must not be transported behind the safety net. Fitting When fitting in front of the rear seats, push head restraints of the rear seats down and fold down rear seat backrests 3 37. Open aperture covers on the roof frame and insert top corners of safety net into large apertures in roof frame and secure by sliding them into the smaller apertures.
Storage First aid kit Stow the first aid kit below the floor cover in the load compartment. Roof rack system Loading information Roof rack ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. Ensure the backrests are securely engaged. If objects can be stacked, the heavier objects should be placed at the bottom.
Storage ■ Do not allow the load to protrude above the upper edge of the backrests. ■ Do not place any objects on the load compartment cover or the instrument panel, and do not cover the sensor on top of the instrument panel. ■ The load must not obstruct the operation of the pedals, electrical parking brake and gear selector, or hinder the freedom of movement of the driver. Do not place any unsecured objects in the interior. ■ Do not drive with an open load compartment.
Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 70 Warning lights, gauges and indicators ..................................... 77 Information displays ..................... 88 Vehicle messages ........................ 96 Trip computer ............................... 97 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Instruments and controls Horn Windscreen wiper/washer 71 Adjustable wiper interval Windscreen wiper Press j. & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Do not use if the windscreen is frozen. Switch off in car washes. To set the wiping interval to a value between 1 and 10 seconds: ■ Switch on ignition. ■ Push lever down from position §.
Instruments and controls In this mode, wiping frequency is also affected by vehicle speed. As vehicle speed increases, wiping will become more frequent. Automatic wiping with rain sensor $ = automatic wiping with rain sensor The rain sensor detects the amount of water on the windscreen and automatically regulates the frequency of the windscreen wiper. The wiper operates for one cycle to check the system when the key is turned to ignition switch position ACC.
Instruments and controls Control indicator G illuminates in the instrument cluster when the washer fluid level is low. Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically. Rear window wiper/washer Move lever to activate the rear window wiper: Push lever = wiper on Pull lever = wiper off To activate rear window washer system, press and hold button on end of lever.
Instruments and controls Automatic time synchronisation 9 Warning Board-Info-Display The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Graphic-Info-Display, Colour-Info-Display 3 91. Date and time are shown in the Info-Display. Board-Info-Display 3 88. The RDS (Radio Data System) signal of most VHF transmitters automatically sets the time, identified by } in the display. Some RDS transmitters do not send a correct time signal.
Instruments and controls Deactivate (Clock Sync.Off) or activate (Clock Sync.on) automatic time synchronisation with the arrow buttons on the Infotainment system. To set date and time manually, select the menu item for time and date setting from the Settings menu and make the desired setting. The value ready for modification is marked with arrows. Use the arrow buttons to make the required setting. The setting is saved when the menu item is exited.
Instruments and controls A 12 Volt power outlet is located in the rear centre console. An additional 12 Volt power outlet is located on the right-hand side of the load compartment. Pull the cap out to use the accessory socket, and replace the cap when not in use. Do not exceed the maximum power consumption of 120 watts. Operational with ignition switch in positions ACC or ON. Use of accessory sockets while the engine is not running will discharge the battery.
Instruments and controls The portable front ashtray can be placed in the front console cupholder. To open: gently lift up lid. Illuminates depending on outside light conditions. To empty: rotate upper part of ashtray anticlockwise and remove. After use, close lid firmly. To replace battery: remove screw on ashtray lid and replace with CR 2032 (or equivalent) battery. Warning lights, gauges and indicators 77 Odometer Speedometer The bottom line displays the recorded distance. Indicates vehicle speed.
Instruments and controls Tachometer Fuel gauge Transmission display Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Displays the fuel level in the tank. Control indicator Y illuminates if the level in the tank is low. Refuel immediately 3 139. Never run the tank dry. Erratic fuel supply can cause catalytic converter to overheat 3 123. Diesel engines: if the tank has been run dry, bleed the fuel system 3 151.
Instruments and controls When the ignition is switched on, most control indicators will illuminate briefly as a functionality test. The control indicator colours mean: red = danger, important reminder yellow = warning, information, fault green = confirmation of activation blue = confirmation of activation Control indicators on the instrument panel V illuminates yellow. The front passenger airbag is activated. * illuminates yellow. The front passenger airbag is deactivated 3 44.
Instruments and controls Control indicators in the instrument cluster
Instruments and controls Turn signal O illuminates or flashes green. The relevant control indicator flashes when the turn signal is switched on 3 105. Rapid flashing: failure of a turn signal bulb or the associated fuse or failure of a turn signal light on trailer. Both control indicators flash when the hazard warning flashers are active 3 104. Bulb replacement 3 152, Fuses 3 159. Turn signals 3 105. Seat belt reminder X illuminates or flashes red.
Instruments and controls Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. If it does not illuminate, seek the assistance of a workshop. Can illuminate briefly when driving; this is normal and does not indicate a system fault. Illuminates when the engine is running Fault in the emission control system. The permitted emission limits may be exceeded. Fuel economy and vehicle driveability may be impaired. Seek the assistance of a workshop immediately.
Instruments and controls When the engine is started, m illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates Electrical parking brake is applied 3 131. Flashes Electrical parking brake is not fully applied or released. Switch on ignition, depress brake pedal and attempt to reset the system by first releasing and then re-applying the electrical parking brake. If m remains flashing, do not drive and seek the assistance of a workshop.
Instruments and controls Descent control system u illuminates yellow and/or green. Both the yellow and green control indicators illuminate briefly when the ignition is switched on. Green Illuminates when system is ready for operation. Flashes during driving when system is in operation, after pressing the u button. When the ignition is switched on, 2 illuminates briefly. If it does not illuminate, stays lit or illuminates during driving, there is a fault in the system.
Instruments and controls Illuminates when ESC has been switched off manually by pressing button t on the centre console. Electronic Stability Control 3 133. Engine coolant temperature W illuminates red. When the engine is started, W illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates when the engine is running Stop vehicle and switch off engine. Caution Coolant temperature too high. Check coolant level 3 148.
Instruments and controls 1. Depress clutch. 2. Select neutral gear, set selector lever to N. 3. Move out of the flow of traffic as quickly as possible without impeding other vehicles. 4. Switch off ignition. 9 Warning When the engine is off, considerably more force is needed to brake and steer. Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly. Check oil level before seeking the assistance of a workshop 3 147.
Instruments and controls Residual water in the diesel fuel filter must be drained 3 151. Seek the assistance of a workshop as soon as possible. Immobiliser d illuminates red. When the engine is started, d illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates to indicate a fault in the immobiliser system. The engine cannot be started. Electronic immobiliser 3 26. Apply footbrake - illuminates yellow.
Instruments and controls Trailer indicator g illuminates green. Illuminates when a trailer is connected to the vehicle 3 141. Door open Information displays Board-Info-Display The Info-Display is located in the instrument panel above the Infotainment system. 9 illuminates red. Illuminates when a door is open or not securely latched. Selecting functions Tailgate open 1 illuminates red. Illuminates when tailgate is open or not securely latched 3 22. Anti-theft alarm system a illuminates yellow.
Instruments and controls Select using the Infotainment system buttons Select using the left adjuster wheel on the steering wheel In the Settings menu, use the OK button to call up the required function. Use the arrow buttons to change settings. In the BC menu, use the OK button to call up the required function. Use the OK button to operate the stop watch or restart measurement and calculation. Turn the adjuster wheel to call up the required function.
■ ■ ■ ■ ■ ■ ■ Instruments and controls Time, setting minutes Date, setting day Date, setting month Date, setting year Ignition logic Language selection Setting units of measure Automatic time synchronisation The RDS (Radio Data System) signal of most VHF transmitters automatically sets the time, identified by } in the display. Some transmitters do not send a correct time signal. In such cases, switch off automatic time synchronisation and set the time manually. Deactivate (Clock Sync.
Instruments and controls Setting units of measure Select the required unit of measurement with the arrow buttons. Graphic-Info-Display, Colour-Info-Display Depending on the vehicle configuration the vehicle has a Graphic-Info-Display or Colour-Info-Display. The Info-Display is located in the instrument panel above the Infotainment system. 91 The type of information and how it is displayed depends on the equipment of the vehicle and the settings of the trip computer and Infotainment system.
Instruments and controls wheel. If there are several warning messages, acknowledge them one at a time. Check control 3 96. Select using the Infotainment system buttons Select a function via the Infotainment system arrow buttons. The menu of the selected function is displayed.
Instruments and controls Function areas System settings 93 ■ Contrast ■ Day / Night ■ Ignition logic Setting date and time For each function area there is a main page (Main), which is selected at the top edge of the display: ■ Audio, ■ Navigation, ■ Telephone, ■ Trip computer. See Infotainment system instruction manual for further information. The settings are accessed via the Settings menu.
Instruments and controls Some RDS transmitters do not send a correct time signal. In such cases, switch off automatic time synchronisation and set the time manually. To set date and time manually, select menu item Time, Date from the Settings menu. The menu is displayed. Select the menu items required and make the desired setting. To correct time with the help of RDS, select menu item Synchron. clock automatical. from the Time, Date menu. The box in front of Synchron. clock automatical.
Instruments and controls Setting units of measure Adjusting contrast (Graphic-Info-Display) 95 Always day design; black or coloured text on a light background. Always night design; white or coloured text on a dark background. Selections are indicated by a o in front of the menu item. Ignition logic See Infotainment system instruction manual. Select menu item Units from the Settings menu. The available units are displayed. Select the desired unit.
Instruments and controls Vehicle messages Warning chimes When starting the engine or whilst driving ■ If seat belt is not fastened. ■ When operating the turn and lanechange signals. ■ When the vehicle is being driven and the electrical parking brake is applied 3 131. ■ When releasing the electrical parking brake without applying the foot brake 3 87. ■ If there is a fault in the braking system 3 82. ■ If the parking assist detects an object 3 137.
Instruments and controls Trip computer Trip computer in BoardInfo-Display The trip computer provides information on driving data, which is continually recorded and evaluated electronically. Access trip computer vehicle data by pressing the BC button on the Infotainment system or the left adjuster wheel on the steering wheel. Some of the functions appear on the display in an abbreviated form. Once a function has been selected, the subsequent rows of the trip computer function are displayed.
Instruments and controls After refuelling, the range is updated automatically after a brief delay. If the fuel in the tank allows less than 50 km of travel, the warning Range appears on the display. If the fuel in the tank allows less than 30 km of travel, the warning Refuel! appears on the display. Acknowledge the menu item 3 88. Stop watch If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost.
Instruments and controls page provides information on range, average consumption and instantaneous consumption. To display other trip computer data, press the BC button on the Infotainment system and select the trip computer menu in the display. The information of the two trip computers can be reset separately, making it possible to display different trip distances. Graphic-Info-Display, Colour-Info-Display 3 91. Range is calculated from current fuel tank content and instantaneous consumption.
Instruments and controls Stop watch Average consumption Display of average consumption. The measurement can be reset at any time. Resetting trip computer information To reset all information of a trip computer, select menu item All values. After resetting, "- - -" is displayed for the trip computer information selected. The recalculated values are displayed after a brief delay. Select BC 1 or BC 2 from the trip computer menu.
Instruments and controls Travel Time: Measurement of the time from manual activation via Start to manual deactivation via Reset. Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost.
Lighting Lighting Exterior lighting Light switch Exterior lighting .......................... 102 Interior lighting ........................... 107 Lighting features ........................ 109 Tail lights Tail lights illuminate together with the headlights and sidelights. Automatic light control Turn light switch: AUTO = Automatic light control: Headlights are switched on and off automatically depending on external lighting conditions. = Off (or deactivation of 7 automatic light control).
Lighting To ensure automatic light control functions properly, do not cover the light sensor on top of the instrument panel. High beam Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically. Headlight range adjustment Manual headlight range adjustment Daytime running lights Daytime running lights increase visibility of the vehicle during daylight.
Lighting Vehicles without automatic level control system Turn thumb wheel to required position: 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 = driver's seat occupied and load compartment laden Vehicles with automatic level control system Turn thumb wheel to required position: 0 = front seats occupied 1 = all seats occupied 1 = all seats occupied and load compartment laden 2 = driver's seat occupied and load compartment laden Automatic level contro
Lighting Turn and lane-change signals For three flashes, e.g. when changing lanes, press the lever until resistance is felt and then release. Move the lever to the resistance point and hold for longer indication. The volume of the turn signal audible warning is dependent upon vehicle speed. Switch the turn signal off manually by moving the lever to its original position. Control indicators O 3 81.
Lighting Rear fog lights The vehicle rear fog light is deactivated when towing. Parking lights Confirmed by a signal tone and the corresponding turn signal control indicator. To deactivate, switch on the ignition or move the turn signal lever in the opposite direction. Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected. Centre high-mounted brake light Operated with the r button.
Lighting Interior lighting Instrument panel illumination control automatically for 30 seconds until ignition switch is turned to position ACC. Display mode 3 91. Interior lights Front courtesy light The instrument panel illuminates when the ignition is switched on. Brightness can be adjusted when the exterior lights are on: Turn thumb wheel to the right or left until the desired brightness is obtained.
Lighting Front door lights Illuminates when a door is opened. Once all doors are closed, the front door lights extinguish after 10 seconds. If the doors are left open, the lights will stay on for 10 seconds. Switch off immediately by pressing button K in the roof lining. Load compartment lighting Reading lights Front reading lights Ignition switch illumination Illuminates when you open a door. Switch off immediately by pressing button K in the roof lining.
Lighting Rear reading lights Lighting features 109 Switching on Entry lighting Welcome lighting Depending upon outside light conditions, when unlocking the vehicle with the remote control the hazard warning lights flash twice and the exterior and interior lights illuminate for 20 seconds. This function facilitates locating the vehicle when it is dark. Left and right rear reading lights are individually operable. Press to activate and deactivate.
Lighting Battery discharge protection To prevent the battery from becoming discharged, the exterior lights turn off automatically 10 minutes after the ignition is switched off. Battery discharge protection will not work if the lights are turned on 10 minutes after the ignition has been switched off; the key cannot be removed from the ignition switch until the battery is recharged.
Infotainment system Infotainment system Introduction ................................ 111 Radio ......................................... 111 Phone ........................................ 112 Introduction Radio Operation Radio reception Infotainment and navigation systems The systems are operated as described in the instruction manuals supplied. The navigation system is supplied with a CD or DVD detailing the local territory.
Infotainment system Phone Mobile phones and CB radio equipment Installation instructions and operating guidelines The vehicle specific installation instructions and the operating guidelines of the mobile phone and handsfree manufacturer must be observed when installing and operating a mobile telephone. Failure to do so could invalidate the vehicle type approval (EU directive 95/54/ EC).
Climate control Climate control Climate control systems ............. 113 Air vents ..................................... 117 Maintenance .............................. 118 Climate control systems Heating and ventilation system 113 Temperature red = warm blue = cold Heating will not be fully effective until the engine has reached normal operating temperature. Air distribution Controls for: ■ Temperature ■ Air distribution ■ Fan speed Heated rear window Ü 3 30. Heated seats 3 37.
Climate control Air conditioning system In addition to the heating and ventilation system, the air conditioning system has: n = cooling 4 = air recirculation Ü = demisting and defrosting Cooling n Operated with the n button and is functional only when the engine and fan are running. freezing point. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required, switch the cooling system off to save fuel.
Climate control Electronic climate control system 115 Do not cover the interior temperature sensor (located below the fan switch) or the sunlight sensor (located in front of the windscreen defroster vents) as this could cause the system to malfunction. Automatic mode AUTO Basic setting for maximum comfort: ■ Set the air distribution switch to l or J. ■ Set temperature control to warmest level. ■ Set fan to highest level. ■ Close centre air vents.
Climate control Recommended comfort setting is 22 °C. Intermediate settings are possible. To deactivate automatic mode, turn fan to position off x. All air vents are actuated automatically in automatic mode. The air vents should therefore always be open. Operated with the t button. The automatic air recirculation system is only operational if the engine is running.
Climate control Air vents 117 The area underneath the front seats must be kept clear, to allow air flow to the rear passenger foot well. Adjustable air vents Glovebox cooler Cooled air is fed into the glovebox through an air opening when the air conditioning is turned on. Direct the flow of air by tilting and swivelling the slats. To open and close the vents, turn the horizontal adjuster wheel to the left or right. Open air vents when air distribution switch is set to M or L.
Climate control Maintenance Air intake Active carbon filter In addition to the particle filter the active carbon filter reduces odours. Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a week, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
Driving and operating Driving and operating Driving hints ............................... 119 Starting and operating ............... 119 Engine exhaust .......................... 122 Automatic transmission .............. 123 Manual transmission .................. 127 Drive systems ............................ 128 Brakes ........................................ 130 Ride control systems ................. 133 Cruise control ............................. 135 Object detection systems ........... 137 Fuel ......
Driving and operating Ignition switch positions Starting the engine Before restarting or to switch off the engine, turn key back to LOCK. Start attempts should not last longer than 15 seconds. If engine does not start, wait 10 seconds before repeating starting procedure. The increased engine speed automatically returns to normal idling speed as the engine temperature rises. Drive at a moderate speed, especially in cold weather, until normal engine operating temperatures have been reached.
Driving and operating Ensure the engine oil is of the correct viscosity, the correct fuel is used, vehicle services are performed regularly and the battery is sufficiently charged. ■ Overrun cut-off The fuel supply is automatically cutoff during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released. Parking ■ Always apply the electrical parking brake. Pull switch m. For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice.
Driving and operating Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases enter the interior of the vehicle, open the windows. Have the cause of the fault rectified by a workshop. Avoid driving with an open load compartment, otherwise exhaust gases could enter the vehicle. The filter is cleaned by periodically burning off the soot particles at high temperature.
Driving and operating may be a fault in the diesel particle filter 3 81. Seek the assistance of a workshop immediately. Caution If the cleaning process is interrupted, there is a risk of provoking severe engine damage. Cleaning takes place quickest at high engine speeds and loads. Control indicator % extinguishes as soon as the self-cleaning operation is complete. Catalytic converter The catalytic converter reduces the amount of harmful substances in the exhaust gases.
Driving and operating D = drive position (automatic mode) 1-6 = selected gear in manual mode Selector lever P = park position, wheels are locked, engage only when the vehicle is stationary and the electrical parking brake is applied R = reverse gear, engage only when vehicle is stationary N = neutral or idle D = drive position (automatic mode with all gears) The selector lever is locked in position P and N and can only be moved when the ignition is on and the foot brake is applied.
Driving and operating Manual mode Move selector lever out of position D towards the left and then forwards or backwards. < = Shift to a higher gear. ] = Shift to a lower gear. Tip selector lever in the appropriate direction. It then returns to the centre position. Gearshifting in manual mode can be achieved whilst accelerating. If the engine speed is too low, the transmission will automatically shift to a lower gear, even in manual mode, to prevent the engine from stalling.
Driving and operating Activation In automatic mode, press button s; control indicator s illuminates in the instrument cluster 3 86. The settings of certain electronic systems are adapted to reduce fuel consumption: ■ The engine reacts less quickly to the accelerator pedal. ■ Automatic upshift points occur sooner and downshift points occur later. ■ The transmission locks itself to the engine at cruising speeds, to improve efficiency and increase power and torque.
Driving and operating 3. Remove trim cover. Manual transmission 127 Caution It is inadvisable to drive with hand resting on the selector lever. 4. Press and hold shift lock release button. 5. Shift to neutral (N). 6. Replace trim cover. 7. Start engine and shift to chosen gear. Have the cause of the power supply interruption remedied by a workshop. To engage reverse, with the vehicle stationary depress clutch pedal and engage the gear.
Driving and operating Drive systems All-wheel drive All-wheel drive is an active-ondemand system that engages automatically, with no action required by the driver. Depending on the driving environment, the vehicle switches between two-wheel drive and four-wheel drive, to give the vehicle more traction and stability when necessary. If the front wheels begin to slip, the rear wheels will automatically begin to drive the vehicle as required.
Driving and operating Towing the vehicle 3 180. Driving through water Do not exceed the maximum wading depth 3 193. Check the depth of water: choose the lowest entry and departure angles before entering. Maintain a steady engine speed, to help prevent water from entering the exhaust system, but do not exceed 5 km/h, to avoid splashing the water. Drive with the flow wherever possible, not against it.
Driving and operating ■ Transfer box and underguard ■ Engine oil pan and underguard Observe the following: ■ Do not spray high-pressure water directly at the vehicle seals ■ The wheels must be removed to clean all mud and stones from the brake calipers and to check brake pad wear ■ The areas on the upper side of the underguards must be cleared of stones, to prevent damage to the engine oil pan and the fuel tank Brakes The brake system comprises two independent brake circuits.
Driving and operating Parking brake Fault 9 Warning Electrical parking brake If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During hard braking, the vehicle can no longer be steered and may swerve. You can continue driving, provided you drive with care and anticipation. Have the cause of the fault remedied by a workshop.
Driving and operating This function also helps driving away on inclines. Aggressive drive away may reduce life time of wear parts. Dynamic braking when vehicle is moving When the vehicle is moving and the switch m is kept pulled, a warning chime will sound and the electrical parking brake system will decelerate the vehicle, but will not apply statically. As soon as the switch m is released, dynamic braking will be stopped.
Driving and operating Ride control systems Electronic Stability Control Electronic Stability Control (ESC) improves driving stability when necessary, regardless of the type of road surface or tyre grip. It also prevents the drive wheels from spinning. As soon as the vehicle starts to swerve (understeer/oversteer), engine output is reduced and the wheels are braked individually. This considerably improves the driving stability of the vehicle on slippery road surfaces.
Driving and operating Trailer stability assist If the system detects snaking movements, engine power is reduced and the vehicle/trailer combination is selectively braked until the snaking ceases. While system is working keep steering wheel as still as possible. Descent control system The Descent control system (DCS) allows the vehicle to travel at a low speed without depressing the foot brake.
Driving and operating temperatures may differ according to vehicle conditions or outside conditions. Flashing or illumination of the yellow control indicator u reminds the driver that the friction material needs to cool down: drive the vehicle without braking as much as possible. If the control indicator does not extinguish, have the cause of the fault remedied by a workshop. DSC control indicators u 3 84. Headlight range adjustment 3 103.
Driving and operating With automatic transmission, only activate cruise control in automatic mode. Control indicator m 3 87. Alternatively accelerate to the desired speed and store by pressing the SET button. Activation With cruise control active, press and hold the - SET button or tap the SET button repeatedly: speed decreases continuously or in small increments. Press the e button; control indicator m illuminates yellow in the instrument cluster.
Driving and operating Object detection systems Control indicator r 3 84. Activation Parking assist The parking assist system makes parking easier by measuring the distance between the vehicle and obstacles to the front and rear, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre. The system consists of four ultrasonic parking sensors in both the front and rear bumpers. 137 When the distance is less than 30 cm, the signal is continuous.
Driving and operating If the acoustic signal sounds 3 times continuously when there are no obstacles near the front or rear bumper, there is a fault in the system. Have the cause of the fault remedied by a workshop. Important hints for using the parking assist system 9 Warning Under certain circumstances, various reflective surfaces on objects or clothing as well as external noise sources may cause the system to fail to detect obstacles.
Driving and operating Fuel for diesel engines Only use diesel fuel that complies with DIN EN 5902). The fuel must have low sulphur content (max. 10 ppm). Equivalent standardised fuels with a biodiesel (= FAME according to EN14214) content of max. 7 % by volume (such as DIN 51628 or equivalent standards) may be used. Country-specific exception for Morocco: use Diesel 50 ppm only.
Driving and operating To unlock fuel filler cap: turn it anticlockwise. If hissing occurs, wait until it stops before completely unscrewing the cap. The fuel filler cap can be retained in the holder on the inside of the fuel filler flap. After refuelling, replace the fuel filler cap and turn it clockwise until you hear several clicks. Ensure the cap is screwed in completely, otherwise control indicator Z may illuminate in the instrument cluster 3 81. Close fuel filler flap.
Driving and operating Towing General information The coupling ball bar is kept in a bag, fastened with a strap and is stowed below the floor cover in the load compartment. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Only use towing equipment that has been approved for your vehicle. Control indicator g illuminates in the instrument cluster when a trailer is connected to the vehicle 3 88.
Driving and operating The permitted trailer load applies up to the specified incline and up to an altitude of 1000 metres above sea level. Since engine power decreases as altitude increases due to the air becoming thinner, therefore reducing climbing ability, the permissible gross train weight also decreases by 10 % for every 1000 metres of additional altitude. The gross train weight does not have to be reduced when driving on roads with slight inclines (less than 8 %, e.g. motorways).
Driving and operating Remove sealing plug from the hole for the coupling ball bar and stow it in the load compartment. Confirm that the colour marking on the lever is red. 143 Inserting the coupling ball bar Insert the coupling ball bar into the coupling housing and push firmly downwards until the coupling ball bar audibly engages. If it does not engage, repeat fitting procedure. Do not swing the coupling ball bar to the left or right, or upwards and downwards, to avoid disrupting correct fitting.
Driving and operating 9 Warning Towing a trailer is permitted only when the coupling ball bar is fitted correctly. If the coupling ball bar cannot be properly attached, seek the assistance of a workshop. Eye for break-away stopping cable In the case of trailers with brakes, attach the break-away stopping cable to the eye - not to the coupling ball bar. Dismounting the coupling ball bar Unlock coupling ball bar and remove key.
Vehicle care Vehicle care General Information ................... 145 Vehicle checks ........................... 146 Bulb replacement ....................... 152 Electrical system ........................ 159 Vehicle tools .............................. 166 Wheels and tyres ....................... 168 Jump starting ............................. 179 Towing ....................................... 180 Appearance care .......................
Vehicle care Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level. ■ Check the coolant level. ■ Fit the number plate if necessary. Seek the assistance of a workshop for further advice.
Vehicle care 147 Engine oil Locate the safety catch, found slightly left of centre on the underside of the bonnet, push the catch upwards and lift the bonnet gently. The bonnet is held open automatically. Air intake 3 118. Closing Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 186.
Vehicle care Control indicators for engine oil pressure I 3 85, low engine oil S 3 86 and engine oil life C 3 86. Once the engine oil has been changed, the engine oil life monitor needs to be reset. Seek the assistance of a workshop. Engine coolant The coolant provides freeze protection down to approx. -28 °C. We recommend the use of the same grade of engine oil that was used at the last oil change. The engine oil level must not exceed the MAX mark on the dipstick.
Vehicle care the coolant concentration checked and have the cause of the coolant loss remedied by a workshop. Engine coolant temperature control indicator W 3 85. Washer fluid Power steering fluid 149 Do not spray washer fluid onto windscreen in freezing weather, to avoid ice forming and impairing vision. In cold weather, do not fill the washer fluid reservoir more than three quarters full, to allow enough room for expansion if the fluid freezes, and to prevent damage to the reservoir.
Vehicle care Brake fluid 9 Warning Brake fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces. Only use high-performance brake fluid approved for the vehicle. Brake fluid 3 186. Brake fluid level control indicator R 3 82. Clutch fluid 9 Warning Clutch fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces. The brake fluid level must be between the MIN and MAX marks.
Vehicle care battery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery. Retrofitted electrical or electronic accessories can place an additional load on the battery or discharge the battery. Seek the assistance of a workshop regarding technical possibilities, such as fitting a more powerful battery. Ensure the ignition is switched off before reconnecting the battery. Then perform the following actions: 1. Set date and time in the information display 3 74. 2.
Vehicle care Wiper blade replacement Bulb replacement Wiper blades on the windscreen Switch off the ignition and turn off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment. Headlights Lift wiper arm, press and hold retaining clip and detach wiper blade. Lower wiper arm carefully.
Vehicle care Halogen headlights Low and high beam 153 5. Engage bulb retaining spring and replace headlamp cap. 6. Reinstall headlamp assembly. Front turn signal Halogen headlights A can be identified from Xenon headlights B by the different lens layout. Halogen headlights have separate systems for high beam 1 (inner bulbs) and low beam 2 (outer bulbs). 1. Remove headlamp assembly 3 152. 2. Remove headlamp cap. 3. Release bulb retaining spring and remove bulb from reflector housing. 4.
Vehicle care 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6. Reinstall headlamp assembly. Sidelights 5. Reinstall bulb holder in lamp assembly and replace headlamp cap. 6. Reinstall headlamp assembly. Xenon headlights Low and high beam 9 Danger Xenon headlights work under extremely high electrical voltage. Do not touch. Have bulbs replaced by a workshop. Front turn signal 1. Remove headlamp assembly 3 152. 2.
Vehicle care 3. Press and rotate bulb anticlockwise to remove it from bulb holder. 4. Insert new bulb into bulb holder by pressing and rotating it clockwise. 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6. Reinstall headlamp assembly. Sidelights 1. Remove headlamp assembly 3 152. 2. Rotate bulb holder anticlockwise and withdraw bulb holder from lamp assembly. 3. Remove bulb from bulb holder by pulling it straight out. 4. Insert new bulb, using a lint-free cloth to hold bulb. 5.
Vehicle care Tail lights Side turn signal lights Rear brake, tail, turn signal, reverse and fog tail light 1. Open the tailgate and remove 2 screws and lamp assembly. 2. Remove bulb holder by rotating it anticlockwise. 3. Remove bulb from bulb holder by pressing the bulb in and rotating it anticlockwise. 4. Insert new bulb into bulb holder. 5. Reinstall bulb holder into lamp assembly. Rotate bulb holder clockwise and ensure it is secure. 6.
Vehicle care Centre high-mounted brake light Have bulbs replaced by a workshop. Number plate light 5. Reinstall bulb holder into lamp assembly, rotate bulb holder clockwise and ensure it is secure. 6. Replace lamp covers using the 4 screws removed earlier. 157 Rear reading lights Interior lights Front reading lights 1. Remove 4 screws (arrowed) and remove lamp covers. 2. Remove bulb holder from lamp assembly by rotating it anticlockwise. 3. Pull bulb straight out of bulb holder. 4. Insert new bulb.
Vehicle care Load compartment light Front door lights Instrument panel illumination Have bulbs replaced by a workshop. 1. Using a suitable screwdriver, remove lens from lamp assembly. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lens to lamp assembly. 1. Using a suitable screwdriver, pry lamp lens away from front door trim. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lamp lens to front door trim. Glovebox light Have bulbs replaced by a workshop.
Vehicle care Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are two fuse boxes in the vehicle: ■ in the engine compartment next to the coolant reservoir, ■ in the instrument panel, on the lefthand side of the front passenger seat foot well, or, in right-hand drive vehicles, on the left-hand side of the driver's seat foot well. Before replacing a fuse, turn off the respective switch and the ignition. A blown fuse can be recognized by its melted wire.
Vehicle care Engine compartment fuse box Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. The fuse box is located next to the coolant reservoir in the engine compartment. To open, disengage cover and tilt upwards.
Vehicle care 161
Vehicle care Fuse Circuit Fuse Circuit Fuse Circuit ABS Anti-lock Brake System FAN1 Cooling fan LO BEAM LH A/C Climate control, air conditioning system FAN3 Cooling fan Low beam (lefthand) FRT FOG Front fog lights LO BEAM RH FRT WPR Front wiper Low beam (righthand) PRK LP LH Parking light (lefthand) PRK LP RH Parking light (righthand) PWM FAN Pulse width modulation fan BATT1 Instrument panel fuse box FUEL/VAC Fuel pump, vacuum pump BATT2 Instrument panel fuse box HDLP
Vehicle care After changing of defective fuses close the fuse box cover and press until it engages. If the fuse box cover is not closed correctly, malfunctions may occur. Instrument panel fuse box The fuse box is located on the lefthand side of the front passenger seat foot well, or, in right-hand drive vehicles, on the left-hand side of the driver's seat foot well. Release latch to open cover.
Vehicle care
Vehicle care 165 Fuse Circuit Fuse Circuit Fuse Circuit AMP Amplifier CIGAR Cigarette lighter Seat heating APO JACK (CONSOLE) Power outlet (centre console) CIM Communications Integration Module HTD SEAT PWR HVAC BLWR APO JACK (REAR CARGO) Power outlet (load compartment) CLSTR Instrument cluster Climate control, air conditioning fan DRL IPC Instrument panel cluster AWD/VENT All-wheel drive, ventilation Daytime running lights DR/LCK Driver door lock ISRVM/RCM BCM (CTSY) Courte
Vehicle care Fuse Circuit Fuse Circuit Vehicle tools RR FOG Heated rear window XBCM Export Body Control Module Tools RUN 2 Power battery key on run XM/HVAC/ DLC Vehicles with spare wheel RUN/CRNK Run crank XM satellite radio, climate control, data link connection SDM (BATT) Safety Diagnosis Module (Battery) SDM (IGN 1) Safety Diagnosis Module (Ignition) SPARE - S/ROOF Sunroof After changing of defective fuses close the fuse box cover and press until it engages.
Vehicle care 167 Remove wing bolt from the jack by rotating it anticlockwise and remove the jack and wheel wrench bag. Remove straps holding the bag containing the wheel wrench. Remove wheel wrench from the bag. Vehicles with tyre repair kit The jack and vehicle tools are in a storage compartment below the floor cover in the load compartment. To remove the jack and vehicle tools, open the tailgate. Push both levers on the floor cover towards the handle and pull up the floor cover by the handle.
Vehicle care the floor cover by the handle. Hang the hook to the upper part of the tailgate opening. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking.
Vehicle care 104 = Load index e.g. 91 is equivalent to 618 kg H = Speed code letter Speed code letter: Q = up to 160 km/h S = up to 180 km/h T = up to 190 km/h H = up to 210 km/h V = up to 240 km/h W = up to 270 km/h Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. This also applies to vehicles with tyre pressure monitoring system. Use the valve cap key to make unscrewing the valve caps easier.
Vehicle care pressures are detected. In some versions, the message is displayed in abbreviated form. For example, the following messages can be displayed: A graphic indicating the left rear tyre is shown together with the current tyre pressure; slight pressure deviation. Reduce speed. Check tyre pressure at next opportunity with an appropriate gauge and correct if necessary. On the Colour-Info-Display, this message will appear in yellow.
Vehicle care Changing tyre and wheel size The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI). Their position is indicated by markings on the sidewall. If there is more wear at the front than the rear, swap round front wheels and rear wheels. Ensure that the direction of rotation of the wheels is the same as before. Tyres age, even if they are not used. We recommend tyre replacement every 6 years.
Vehicle care Tyre chains Tyre chains are permitted only on tyres of size 215/70 R 16. We recommend you consult your service partner. The use of tyre chains is not permitted on the temporary spare wheel. If the use of tyre chains is required after suffering a flat front tyre, fit the temporary spare wheel on the rear axle and transfer one of the rear wheels to the front axle. Tyre repair kit Tyre chains are only permitted on the front wheels.
Vehicle care Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. 1. Release the sealant filler hose 1 and the power plug 2. 2. Unscrew valve cap from defective tyre. Screw the sealant filler hose onto the tyre valve. 173 3. Connect the power plug to the power outlet or cigarette lighter socket. Unplug all items from other power outlets. 4. Switch on ignition.
Vehicle care is obtained, switch off the compressor. If the prescribed tyre pressure is not obtained within 10 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation. Reattach the tyre repair kit and continue the filling procedure for 10 minutes. If the prescribed tyre pressure is still not obtained, the tyre is too badly damaged. Seek the assistance of a workshop. Drain excess tyre pressure with the button next to the pressure gauge.
Vehicle care 13. Turn the selector switch clockwise to the air only position. Switch on the compressor to inflate the tyre with air only. Note The driving characteristic of the repaired tyre is severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed. Pay attention to storage information on sealant canister.
Vehicle care ■ Do not raise the vehicle more than is necessary to change a wheel. ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the engine when it is raised on the jack. ■ Clean wheel nuts and thread before mounting the wheel. 1. Pull off the wheel cover. 2. Install the wheel wrench ensuring that it locates securely and loosen each wheel nut by one turn by turning anticlockwise.
Vehicle care 8. Screw on the wheel nuts and tighten slightly by hand by turning clockwise until wheel is held against the hub. 9. Rotate wrench anticlockwise and lower vehicle to the ground. Have the defective tyre renewed and replace temporary spare wheel with a full specification wheel without delay. Spare wheel Temporary spare wheel 5. Attach wheel wrench to eye of threaded rod and rotate wrench clockwise to raise vehicle.
Vehicle care The temporary spare wheel is located in the load compartment below the floor cover and is secured with a screw-in retainer. Push both levers on the floor cover towards the handle and pull up floor cover by the handle. Hang the hook to the upper part of the tailgate opening. Vehicle tools 3 166. Remove the retainer by rotating it anticlockwise and remove temporary spare wheel from the spare wheel well. Only mount one temporary spare wheel. Do not drive faster than 80 km/h.
Vehicle care Jump starting Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. 9 Warning Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. 9 Warning Avoid contact of the battery with eyes, skin, fabrics and painted surfaces.
Vehicle care 3. Connect the black lead to the negative terminal 3 of the booster battery. 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block 4 or an engine mounting bolt. Connect as far away from the discharged battery as possible, however at least 60 cm. Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump start. 2.
Vehicle care Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. Switch on the hazard warning lights on both vehicles. Turn key to ignition switch position ACC and release the electrical parking brake before towing the vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. When the engine is not running, considerably more force is needed to brake and steer.
Vehicle care Screw the rear towing eye attachment anticlockwise using a suitable screwdriver, until it is firmly in place and stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the rear towing eye. The towing eye must only be used for towing and not for recovering a vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. To prevent damage, do not take up slack in the tow rope too quickly.
Vehicle care Exterior lights Headlight and other light covers are made of plastic. Do not use any abrasive or caustic agents, do not use an ice scraper, and do not clean them dry. Polishing and waxing Wax the vehicle regularly (at the latest when water no longer beads). Otherwise, the paintwork will dry out. Polishing is necessary only if the paint has become dull or if solid deposits have become attached to it. Paintwork polish with silicone forms a protective film, making waxing unnecessary.
Vehicle care alternator and brake fluid reservoir with plastic sheets before washing the engine. When washing the engine with a steam-jet cleaner, do not direct the steam jet towards components of the antilock brake system, air conditioning system or the belt drive and its components. After an engine wash, have all engine compartment components preserved thoroughly by a workshop using protective wax. Do not use high-pressure jet cleaners.
Service and maintenance Service and maintenance General information ................... 185 Recommended fluids, lubricants and parts .................................... 186 General information Service information 185 Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, United Kingdom.
Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that have been tested and approved. Damage resulting from the use of nonapproved materials will not be covered by the warranty. 9 Warning Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers. Engine oil Engine oil is identified by its quality and its viscosity.
Service and maintenance Engine oil viscosity Use only engine oil viscosities SAE 0W-30, 0W-40, 5W-30 or 5W-40. The SAE viscosity grade gives information of the thickness of the oil. Multigrade oil is indicated by two figures. The first figure, followed by a W, indicates low temperature viscosity and the second figure the high temperature viscosity. Select the appropriate viscosity grade depending on the minimum ambient temperature.
Technical data Technical data Vehicle identification .................. 188 Vehicle data ............................... 190 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is also engraved on the top right-hand side of the bulkhead near the centre of the engine firewall. The Vehicle Identification Number is visible through the windscreen.
Technical data Identification plate The identification plate is attached to the top of the front panel support, visible when the bonnet is open.
Technical data Vehicle data Engine data Sales designation 2.4 3.0 V6 2.2 CDTI 2.
Technical data 191 Performance All-wheel drive Engine A 24 XE A 30 XH A 22 DM A 22 DMH Manual transmission 186 – 188 200 Automatic transmission 175 198 182 191 A 24 XE A 30 XH A 22 DM A 22 DMH Manual transmission 190 – 189 – Automatic transmission – – 184 – Maximum speed3) [km/h] Front-wheel drive Engine Maximum speed3) [km/h] 3) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
Technical data Fuel consumption - CO2-emissions All-wheel drive Manual transmission / Automatic transmission. Engine A 24 XE A 30 XH A 22 DM A 22 DMH urban [l/100 km] 12.2 / 12.8 - / 15.9 4) 4) extra-urban [l/100 km] 7.4 / 7.3 - / 7.9 4) 4) total [l/100 km] 9.1 / 9.3 - / 10.9 4) 4) CO2 [g/km] 213 / 219 - / 255 4) 4) Front-wheel drive Manual transmission / Automatic transmission. Engine A 24 XE A 30 XH A 22 DM A 22 DMH urban [l/100 km] 11.
Technical data Vehicle weight Kerb weight, basic model without any optional equipment Manual transmission / Automatic transmission.
Technical data Turning circle diameter, wall to wall [m] 12.78 Turning circle diameter, kerb to kerb [m] 11.87 Maximum wading depth [mm] (at 5 km/h) 450 Approach angle 20° Ramp angle 18° Departure angle 24° Capacities Engine oil Engine A 24 XE A 30 XH A 22 DM A 22 DMH including filter [l] 4.7 5.7 5.6 5.6 between MIN and MAX [l] 1.0 1.0 1.0 1.
Technical data 195 Tyre pressures Up to full load Engine Tyres All 5) Up to full load ECO Trailer towing front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 260/2.6 (38) 240/2.4 (35) 280/2.8 (41) T 155/90 R 16 420/4.2 (60) (Temporary spare) 420/4.2 (60) – – 420/4.2 (60) 420/4.
Technical data Towing hitch installation dimensions Dimension mm A 416 B 507 C 482 D 734 E 1039 F (fully laden) 353 G (at kerb weight) 44+
Technical data 197
Customer information Customer information Vehicle data recording and privacy ....................................... 198 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data. Some data may be stored during regular operation to facilitate repair of detected malfunctions, other data is stored only in a crash or near crash event by systems commonly called event data recorders (EDR).
Customer information 199
Index A Accessories and vehicle modifications .......................... 145 Accessory sockets........................ 75 Active head restraints................... 32 Adjustable air vents ................... 117 Airbag and belt tensioners ........... 81 Airbag deactivation ...................... 44 Airbag system .............................. 42 Air conditioning regular operation ................................ 118 Air conditioning system .............. 114 Air intake ...............................
Check control................................ 96 Child locks ................................... 21 Child restraint installation locations ................................... 48 Child restraint systems ................ 46 Cigarette lighter ........................... 76 Cleaning the vehicle................... 182 Climate control ............................. 14 Clock ............................................ 74 Clutch fluid.................................. 150 Coin storage...........................
H Halogen headlights .................... 153 Hand brake................................. 131 Hazard warning flashers ............ 104 Headlight flash ........................... 103 Headlight range adjustment ...... 103 Headlights.......................... 103, 152 Headlights when driving abroad 104 Headlight washer.......................... 71 Head restraint adjustment ............. 8 Head restraints ............................ 32 Heated .........................................
Performing work ........................ 146 Pollen filter ................................. 118 Power outlets ............................... 75 Power seat adjustment................. 35 Power steering.............................. 84 Power steering fluid.................... 149 Power windows ............................ 29 Preheating ................................... 85 R Radio reception ......................... 111 Radio remote control ................... 18 Rain sensor..........................
Tyre pressure monitoring system............................... 96, 169 Tyre pressures ........................... 195 Tyre repair kit ............................. 172 Tyres .......................................... 168 Tyres and wheel size, changing. 171 U Ultrasonic parking assist .............. 84 Underseat storage ....................... 54 Upholstery, cleaning................... 184 Upshift.......................................... 83 Using this manual ..........................
