Installation Manual

ManualsBrandsOptex ManualsBurglar AlarmsOutdoor 4 CH. Dual Beam w/ Relay Output

WARNING

Failure to follow the instructions provided with this indication and improper handling may cause death or

serious injury.

CAUTION

Failure to follow the instructions provided with this indication and improper handling may cause injury

and / or property damage.

WARNING

Do not use the product for purposes other than the detection of moving objects such as people and vehicles.

Do not use the product to activate a shutter, etc., which may cause an accident.

Do not touch the unit base or power terminals of the product with a wet hand (do not touch when the

product is wet with rain, etc.). It may cause electric shock.

Never attempt to disassemble or repair the product. It may cause ﬁ re or damage to the devices.

Do not exceed the voltage or current rating speciﬁ ed for any of the terminals during installation, doing so

may cause ﬁ re or damage to the devices.

CAUTION

Do not pour water over the product with a bucket, hose, etc. The water may enter, which may cause damage

to the devices.

Clean and check the product periodically for safe use. If any problem is found, do not attempt to use the

product as it is and have the product repaired by a professional engineer or electrician.

INSTALLATION MANUAL

・

Read this instruction manual carefully prior to installation.

・

After reading, store this manual carefully in an easily accessible place for reference.

・

This manual uses the following warning indications for correct use of the product and harm to you or other people and damage to

your assets, which are described below. Be sure to understand the description before reading the rest of this manual.

No. 59-1282-6 0808-20

PHOTOELECTRIC DETECTOR

AX-70TN, AX-130TN, AX-200TN

AX-100TF, AX-200TF

This symbol indicates prohibition. The speciﬁ c prohibited action is provided in and/or around the ﬁ guer.

This symbol requires an action or gives an instruction.

1. PRECAUTIONS

2. PARTS IDENTIFICATION

3. INSTALLATION

3-1 NOTE

3-2 INSTALLATION METHOD

4. WIRE CONNECTION

5. ALIGNMENT

5-1 OPTICAL ALIGNMENT

5-2 BEAM INTERRUPTION TIME

5-3 4 SELECTABLE BEAM FREQUENCIES * TF ONLY

6. WALK TEST

7. SPECIAL FUNCTION * TF ONLY

7-1 ENVIRONMENTAL DISQUALIFICATION

7-2 ALARM MEMORY

8. OPTIONAL ACCESSORIES

8-1 HEATING UNIT : HU-3

8-2 BACK COVER : BC-3

8-3 POLE SIDE COVER : PSC-3

9. TROUBLE SHOOTING

10. SPECIFICATIONS

CONTENTS

For Safe Use of the Product

< STANDARD >

< 4 SELECTABLE BEAM FREQUENCIES >

• 4 selectable beam frequencies

• LED indicator for ﬁ ne beam alignment level

• D.Q. circuit (Environmental disqualiﬁ cation)

• Alarm memory

< AX-100/200TF ONLY >

• High-performance waterproof structure

• Horizontal alignment dial for user-friendliness

• Adjustable beam interruption period

• Tamper function

• Optional Accessories : Heating unit (HU-3), Back cover (BC-3),

Pole side cover (PSC-3)

• UL Listed

< AX-70/130/200TN, AX-100/200TF >

Features

N219

Summary of content (8 pages)

PAGE 1
No. 59-1282-6 0808-20 INSTALLATION MANUAL PHOTOELECTRIC DETECTOR AX-70TN, AX-130TN, AX-200TN AX-100TF, AX-200TF < STANDARD > N219 < 4 SELECTABLE BEAM FREQUENCIES > Features < AX-70/130/200TN, AX-100/200TF > • High-performance waterproof structure < AX-100/200TF ONLY > • 4 selectable beam frequencies • Horizontal alignment dial for user-friendliness • LED indicator for fine beam alignment level • Adjustable beam interruption period • D.Q.
PAGE 2
1. PRECAUTIONS 2. Do not install the unit where objects moved by the wind such as plants and laundry, which may block the beam. 1. Mount unit only on a solid surface. 3. Prevent direct sunlight from entering into internal receiver. 3 4. A different type of beam should not reach the receiver. receiver 6. Do not install the unit on unsteady surfaces. 5. Avoid aerial wiring. 7. Mount the units more than 1m away from the wall or fence. transmitter 3.3 ft. (1m) transmitter (other model) 2.
PAGE 3
. Wiring Use wires in compliance with the following conditions: 1) Wire diameter: φ4 - 7mm 2) When using any other wires than the above, seal the wiring port with a waterproof agent (silicon, etc.) to prevent water from coming in through the gap. 3) Number of wires: 3 (max.) Cutting Knockout Wiring Hole 2 Wiring Hole 1 Knockout 3 wires can be accommodated in a unit. Lead-in wire should be as below. Figure 1 *Wiring hole 2 needs to be punched with a screw driver, etc.
PAGE 4
5. ALIGNMENT 5-1 OPTICAL ALIGNMENT The optical alignment is an important adjustment to increase reliability. In accordance with the procedure indicated in the items 1. and 2. in this chapter, make sure to align the monitor jack that monitor output nothing to attain the maximum level. 1. Rough alignment by viewfinder ・While looking through the viewfinder, turn the dial to make alignment in such a way that the other detector is at the center of the sights.
PAGE 5
《EXAMPLE》 1. Long distance protection 2. Double stacked long distance protection receiver receiver transmitter transmitterA receiverA receiverB Ch1 Ch1 transmitterB transmitterC Ch1 Ch1 receiverC Ch3 Ch3 Ch1 Ch1 Ch3 Ch3 Note 3. Perimeter protection Ch1 Ch1 receiver receiver transmitter receiver transmitter transmitter Ch2 Ch2 receiver transmitter transmitter Ch3 Ch3 Ch4 Ch4 More than double stacked apprication is not possible. 4.
PAGE 6
7-2 ALARM MEMORY * TF ONLY This function is used to indicate which detector was activated with alarm memory LED while several detectors are installed in one site. For first 5 minutes after the alarm output, the alarm memory indicator do not light up. Then the alarm memory indicator keep lighting up for 55 minutes. 5 minutes. Alarm memory record is cleared after alarm memory indicator is turned off.
PAGE 7
8-2 BACK COVER : BC-3 1. Cutout of the knockout 2. Installation of mounting plate 3. Installation of the unit base and the back cover Mounting plate lock screws (for main unit) Back cover lock screw (The same applies to the opposite side.) Unit Base Optional pole bracket (for BC-3) Back Cover Cut with cutter. Pole lock screws (for main unit) Knockout Knockout (The same applies to the opposite side.
PAGE 8
10. SPECIFICATIONS Name Heating unit Model AX-70TN AX-130TN AX-200TN AX-100TF AX-200TF Model HU-3 Range 70ft (20m) 130ft (40m) 200ft (60m) 100ft (30m) 200ft (60m) Power input 24VAC/DC Maximum arrival distance 700ft (200m) 1300ft (400m) 2000ft (600m) 1000ft (300m) 2000ft (600m) Current draw 420mA(max.) (Per 1 unit) Thermo switch 140°F (60℃) Operating temperature –31°F– +140°F (–35– +60℃) Weight 0.