User Manual
Table Of Contents
- Notice
- Document Part Number
- Trademarks
- Technical Services Contact Information
- Document Conventions
- EN6080 Area Control Gateway Overview
- 1.1 Introduction
- 1.2 Recommended System Requirements
- 1.3 EN6080 Area Control Gateway Initial Setup and Connection
- 1.3.1 Configure Network Settings (for Windows 7)
- 1.3.2 Disable Delayed ACK Mode on the Windows® 7 Operating System
- 1.3.3 Browse to the EN6080 Area Control Gateway Web Server Screens
- 1.3.4 License Key Setup
- Home
- 2.1 Home
- 2.1.1 System Connection Summary
- 2.1.2 Device Information
- 2.2 Site Information
- 2.2.1 ACG Information
- 2.2.2 Contact Information
- ACG Setup
- 3.1 User Administration
- 3.1.1 Update User or Admin Password
- 3.2 IP Administration
- 3.2.1 Configure a Static IP Address
- 3.2.2 Configure a DHCP IP Address
- 3.3 Date and Time Setup
- 3.3.1 Poll NTP Servers for Time and Date
- 3.3.2 Synchronize Time and Date with your PC
- Partitions
- 4.1 Partitions
- 4.2 Define a New Partition
- 4.3 Assign Devices to a Partition
- 4.4 Remove Devices from a Partition
- 4.5 Update a Partition
- 4.6 Delete a Partition
- Wireless Setup
- 5.1 Wireless Setup
- 5.1.1 Update the NID
- Device Setup
- 6.1 Manual Administration
- 6.1.1 Manually Register a Device
- 6.1.2 Unregister a Registered Device
- 6.2 Automatic Administration
- 6.2.1 Start Discovery
- 6.2.2 Edit and Register the Devices
- 6.2.3 Unregister a Registered Device
- 6.3 Upload Administration
- 6.3.1 Upload a Spreadsheet of Devices to Register
- Logs
- 7.1 Logs
- 7.2 Alarm Logs
- 7.2.1 Retrieve and Save Logs
- 7.3 System Logs
- 7.3.1 Retrieve and Save System Logs
- 7.4 Trouble Logs
- 7.4.1 Retrieve and Save Trouble Logs
- File Management
- 8.1 System and Configuration Files
- 8.1.1 Back Up Configuration Files
- 8.1.2 Restore Configuration Files
- 8.2 Firmware Update
- 8.2.1 Update Firmware
ACG Setup
7/28/17 06443H © 2017, Inovonics - www.inovonics.com 19
6. A dialog box will display, reading “This update will require a reboot of the
ACG. Once you make this change the browser will automatically update
to the new address. Are you sure you want to make this change?” Click
“OK.”
7. When the “Refresh” button displays, click it.
3.2.2 Configure a DHCP IP Address
Caution: Because the EN6080 area control gateway does not provide a unique host
name with the DHCP request, Inovonics strongly recommends a static IP
address. A static IP address will also prevent the possibility of the existence of
a rogue or malfunctioning DHCP server that may pose a security risk.
By default, the EN6080 is configured with a static IP of 192.168.60.80 and a
subnet mask of 255.255.255.0. You will also need to ensure that the target
network has a DHCP server on it.
1. Select the “DHCP” radio button.
2. Click “Update.”
3. A dialog box will display, reading “This update will require a reboot of the
ACG. Once you make this change the browser will automatically update
to the new address. Are you sure you want to make this change?” Click
“OK.”
The EN6080 area control gateway will request a new IP address from the
DHCP server and, if successful, display the IP update dialog box shown in
Figure 3-3. Write down the new IP address displayed in the IP update dialog
box.
Figure 3-3 IP update dialog box
4. Click “Accept New IP.”
5. The EN6080 area control gateway will reboot. When the “Refresh” button
displays, click it.