INSTALLATION GUIDE

ManualsBrandsOptex ManualsIndoor StationsiVision+ Connect Mobile Station

No.59-2723-5 1904-09

SETTINGS and INSTALLATION GUIDE

Door station

IVPC-DS

Mobile station

IVPC-MS

or a device (not included) running the OPTEX Vision App.

- 1 -

This guide covers the installation and setup of the basic IVPC Wireless Intercom System. The basic system

contains an IVPC-DS door station and an IVPC-MS mobile station or a device running the OPTEX Vision App.

By the end of the steps, you will be ready to try some of the operations covered in the user manual.

Thank you for choosing OPTEX!

Introduction

General Information

LED indications

HD camera

Light sensor

Speaker

Power on/off

(Short press to turn

power on/off)

Micro USB port

(For battery charging)

Doorbell

button

LED indicator

Microphone

Factory reset

(Press & hold for 5 seconds, until

white & blue LED starts blinking)

* Lift rubber plug for access.

Internal 5,000 mAh

rechargeable battery

AC/DC power Input

Internal/external

antenna switch

*Memory card slot

(Memory card is installed

as a factory default)

Screw pack

USB charging cable

Power cable

Bypass cable

< Accessories >

2. Open the front cover

1.Open the rubber bushing

INT/EXT

External antenna jack

IVPC-DS

Device ID

Back up QR code

(Do not remove)

Mounting plate

Back cover

Front view

Rear view

(Mounting plate/

back cover removed)

Bottom view

Power on

(Wired operation)

Power on

(Battery operation)

Wi-Fi pairing mode

Active Call/Live View

* Low battery warning: The device will cease to function within a week if not recharged

** Low battery error: The battery is completely drained. Please recharge immediately.

*** Device error: Please contact a service provider.

Solid light (White)

LED OFF

White & Blue alternating

Slow blinking (White)

Solid light (White)

** Low battery error

Battery power charging

Firmware update in progress

*** Device error

Slow blinking (Blue)

Fast blinking (Blue)

Slow blinking (White) off

Solid light (Blue)

Fast blinking (Blue & White)

Active Call/Live View

(2-way Audio Activated)

*Low battery Warning

Full charged

Cable connector

Summary of content (8 pages)

PAGE 1
No.59-2723-5 1904-09 SETTINGS and INSTALLATION GUIDE EN Door station IVPC-DS Mobile station IVPC-MS or a device (not included) running the OPTEX Vision App. Introduction This guide covers the installation and setup of the basic IVPC Wireless Intercom System. The basic system contains an IVPC-DS door station and an IVPC-MS mobile station or a device running the OPTEX Vision App. By the end of the steps, you will be ready to try some of the operations covered in the user manual.
PAGE 2
IVPC-MS Volume UP/DOWN (7 steps) Unused Micro USB port (for battery charge) Stand h nc 7-i < Accessories > AC/DC adapter (micro USB) Micro SD card slot Speaker Microphone Power ON/OFF What to expect 1 1 Collect information; to register (pair) the IVPC system to the Wi-Fi network. 2 Set up for pairing; prepare each device for the pairing processes. 3 Pair the IVPC-DS; pair the IVPC-DS to the IVPC-MS or a device running the OPTEX Vision App and test them.
PAGE 3
2 Set up for pairing IVPC-DS 1 Loosen the lock screw. 2 Remove the mounting plate. 3 Remove the front cover. 1 Slide the 1 main unit. Lift up. 2 Remove the rubber bushing. 2 Pull off the main unit. 4 Power on. Insert a flat driver bit to pry open. 5 Replace the front cover. 12 1 6 Push the front cover to secure. Push. Replace the rubber bushing. Push the power on/off button. Confirm LED is flashing blue & white. This is the pairing mode.
PAGE 4
3 Pair the IVPC-DS - Follow the guidance on the screen to register the IVPC-DS to the IVPC-MS. - Changes can be made using the device and app settings covered in the user manual. IVPC-MS Press the icon. Startup Start of the registration steps End of the registration steps << To use the system with a device running the OPTEX Vision App. (option) >> - Follow the guidance on the screen to register the IVPC-DS to a device running the OPTEX Vision App.
PAGE 5
Mount the IVPC-DS - Choose battery or wired operation. Battery operation 3 Tighten the lock screw. 2 Mount the main unit. 1 Fix the mounting plate. 1 Attach the main unit. 2 Slide down. << Battery charging >> - Charging not needed for wired operation. Micro USB port (For battery charging) - Use the included USB cable with any USB port power supply or charge station capable of delivering 5 V DC at 1A or greater. - Full charge time will be approximately 10 hours.
PAGE 6
<< Retrofit wiring >> - Existing cables and power source for a door chime can be used to power the IVPC-DS. - Existing door button and chime are not used for this installation. FRONT 1 2 Existing doorbell 3 FRONT TRANS IVPC-DS Existing chime TRANS Existing chime REAR (not used) REAR 4 5 Power source Power source 10 to 24 V AC/DC 10 to 24 V AC/DC 1 Turn off power. Disconnect all wires 2 Remove the existing doorbell. from the existing chime. 3 Mount the IVPC-DS instead.
PAGE 7
<< Specifications >> 32(1.26) Unit:mm (inches) 148 (5.83) 36(1.42) 190 (7.49) Model 16 (0.63) Audio direction n 7-i Wi-FI 126 (4.96) ch FCC Statement ° IVPC-DS H.264 720p HD/VGA MP4 H135°/ V75° Two ways (Full duplex) Wi-Fi 802.11 b/g/n 2.
PAGE 8
<< Troubleshooting >> Additional troubleshooting available online at URL; ivisionplusconnect.info/techtips. Status Check point The registration was not completed successfully. The IVPC-DS will change from blue/white blinking to no light or solid white. Solution Did something go wrong during the wizard? e.g. Wi-Fi password is incorrect. Press and hold the factory reset button on the IVPC-DS, to enter the Wi-Fi registration mode. Retry to set each item.