Manual

ManualsBrandsOptex ManualsElectronicsPoE IP Encoder for SIP, RLS & RBM Detectors

PoE IP Encoder

PIE-1

PoE IP Encoder

PIE-1

INSTALLATION INSTRUCTIONS

( for SIP series and RLS series )



▪ PIE-1 changes analog relay output signals (N.C.) to

original ASCII code.

▪ PIE-1 can supply power to detector using a PoE hub

or switch.

▪ Follow all cautions and instructions in this manual

before installation.

▪ Keep this manual after installation so that you can

read when necessary.

▪ Remember the meanings of “Warning” and

“Caution” below to use the product safely.

If you ignore a caution, the user or other

people may be injured or the product or

something around it may be damaged.

If you ignore a warning, the user or other

people may be injured or dead.

▪ Do not repair, dismantle or modify the product

yourself.

▪ Do not touch the product with a wet hand.

▪ Be careful not to damage other interior wiring when

installing or wiring the product.

▪ Power off the product immediately if smoke, odor or

strange sound emits from the product.

▪ Do not install the product in an extremely moist place

such as a bathroom or a place where the product

may be wet.

▪ Insert the connectors securely when wiring.

Caution

SAFETY PRECAUTION

FEATURES

PREPARATIONS

SETTINGS ON THE WEB

REDWALL EVENT CODE SPECIFICATIONS

REDWALL EVENT CODE LOGGER

Q&A

CONTENTS

WarningWarning

Warning: This is a class A product. In a domestic

environment this product may cause radio interference

in which case the user may be required to take

adequate measures. (EN55022)

CE Statement

Warning

Caution

PREPARATIONS

An example of IP address settings

IP Address

Subnet Mask

: 192.168.0.1

: 255.255.255.0

The default settings of PIE-1 are as follows.

IP Address: 192.168.0.126

Subnet Mask: 255.255.255.0

Default Gateway: 0.0.0.0

Before using PIE-1, set the IP addresses of PIE-1 and

the computer in the following procedure.

(1) Set the local area connection.

(6) After changing settings. Click “Save Config” button.

(2) Using Internet Explorer, access the site below.

(http://192.168.0.126/)

(3) Enter the user ID and the password below.

User ID: PIE-1

Password: OPTEX

(4) Change the IP

address if

necessary.

(5) Select the

detector you

have

connected.

No.5919560

2012.5.25

Detailed Version

- 1 -

Summary of content (6 pages)

PAGE 1
No.5919560 PoE IP Encoder PIE-1 FEATURES INSTALLATION INSTRUCTIONS ( for SIP series and RLS series ) Detailed Version CONTENTS ▪ PIE-1 changes analog relay output signals (N.C.) to original ASCII code. ▪ PIE-1 can supply power to detector using a PoE hub or switch. SAFETY PRECAUTION ▪ Follow all cautions and instructions in this manual before installation. ▪ Keep this manual after installation so that you can read when necessary.
PAGE 2
SETTINGS ON THE WEB You can confirm the information below by accessing PIE-1 with Internet Explorer 8 or 9. ▪ Confirming the status of input terminals of PIE-1 ▪ Confirming the transmitted data of REDWALL Event Code (R.E.C.) ▪ Confirming the software version ▪ Managing the network settings ▪ Managing the transmission settings of R.E.C. ▪ Managing the settings of alarm input ▪ Changing the user ID or password ▪ Restarting PIE-1 To access the Web screen of PIE-1, enter the URL below in the browser.
PAGE 3
█ █ Event Code Configuration: to change the transmission settings of R.E.C. ▪ Use an arbitrary number: to define how to set the ID of Detector. When this item is unchecked, the value of the ID of Detector is automatically set as the right-end part of the IP Address. ▪ ID of Detector: to change the number of R.E.C. You can specify the number ranging from 0 to 999. ▪ Transmission Mode: to change the transmission mode of R.E.C. [UDP] ▪ IP Address: to change the IP address to which an R.E.C.
PAGE 4
3 REDWALL EVENT CODE SPECIFICATIONS PIE-1 generates event codes which can be used by an NVR or VMS software to control PTZ cameras and other devices. REDWALL EVENT CODE can be sent to the assigned port using UDP or TCP protocol. The default port number is “1234”. When you connect PIE-1 to REDSCAN, REDWALL EVENT CODE is generated from REDSCAN. Please refer to the manual for REDSCAN when you use it.
PAGE 5
4 REDWALL EVENT CODE LOGGER Double-click the REDWALL Event Code Logger.exe. Logger is a program to display REDWALL Event Codes (R.E.C.) sent from a device on the network and to save the information as a text in a file. Using this program, you can check the reception of R.E.C. This program is working on a computer which is installed with .NET Framework 3.5 or higher. Before using this program, obtain .NET Framework 3.5 on the Microsoft website and install it on your computer.
PAGE 6
5 Q&A No. Problems (1) PIE-1 does not turn on. (The LED does not turn on.) Connection Detector Check Solution SIP, REDSCAN SIP, REDSCAN Is the LAN connector firmly plugged to PIE-1? Is the LAN connector plugged into the right port? Is your Hub or Switch compliant to PoE? Is PoE of your Hub or Switch powered on? Plug the LAN connector into the right port. Use a PoE-compliant Hub or Switch correctly.