User’s Manual LGZ 7225 Long Range Handheld CCD Scanner 25-ULGZMU01-01 Keyboard Wedge Interface USB Interface RS232 Interface 8 Olympic Drive Orangeburg, NY 10962 Tel 800.636.0090 Fax 845.365.1251 www.opticonUSA.
Contents General Information Unpacking Opticon Customer Service and Support Installation Default Settings Interface Selection Scanning Modes Beeper Settings Symbology Options Prefix/Suffix Strings Transmission Setting Parameter Settings List Programming Bar Codes 2 .
Getting Started General Information The LGZ 7225 CCD Scanner utilizes state-of-the art imaging technology similar to that found in digital cameras, fax machines and video camcorders. The captures an “image” of the bar code and converts it into digital signals that the host computer understands. The scanner automatically recognizes most common bar code symbologies. The scanner, which utilizes miniature, surface-mounted electronics, has no moving parts and will provide years of trouble-free operation.
LGZ7225 Long Range Handheld CCD Spec Cable - K/B Wedge Cable - universal type Connector type Case material Cushion material 160 g (cable not included) Straight 2.0 m Straight 2.3 m RJ-45 phone jack connector ABS plastic Rubber Electrical 5 VDC r 0.
Default Setting for each barcode shown as below: Code Type Read UPC-A UPC-E EAN-13 EAN-8 Code-39 Interleaved 2of5 Industrial 2of5 Matrix 2of5 Standard 2of5 China Post Codabar Code-128 Code-93 Code-11 MSI/Plessey UK/Plessey Telepen Italian Pharmaode.
Programming Programming method Manual (Reading special barcode) DOS command through RS-232, Windows configuration program Program upgrade Enabled by built-in flash memory Programmable Code type selection, check digit characteristics selection Decoding option Decoding option Transmitted character delay, Header selection, trailer selection, message suffix, good read beep tone and volume, scanner trigger selection Keyboard emulation type (intermessage delay, keyboard type and keyboard language) Serial i
Programming the LGZ7225 To program the LGZ7225 you must scan a series of programming barcode in the correct order. Fold out the back cover of this manual. You will see a table of alphanumeric barcodes, which are used to program the various options presented. To program each option, you must: 1. Scan the Program barcode on the parameter setting part. 2. Enter the option mode by scanning the Option Bar Code (also on the Parameter setting part). 3.
Program Barcode Program Option Bar Code Option Alphanumeric Entry Keyboard Wedge 00ഖ Interface RS-232 01 selection Wand emulation 02 USB 03 Keyboard/RS-232 04 Auto detection reserved 05 Exit Option Barcode Back Fold Out Exit Barcode Finish barcode 8
Interface Selection This decoder built-in scanner comes in one model and supports interfaces such as keyboard wedge, RS232 serial wedge, wand emulation, and the latest USB interface. In most of the cases, simply sutilizing the an appropriate cable with a device code will work for a specific interface. Interface selection: You can change factory interface default for other type interface. By plugging different cables, setting correct interface, then the scanner will be changed to another interface.
Keyboard wedge As a keyboard interface, the scanner supports most of the popular PCs and IBM terminals. The installation of the wedge is a fairly simple process without any changes of software or hardware. Keyboard Type: Select keyboard type connector of your host computer. Scanner must be selected to the appropriate host interface cable converter.
Keyboard wedge Keyboard Layout: The selecting of keyboard layout supports many country languages other than USA keyboard layout. First you need to confirm country language that you desire. In DOS, using command “keyb” to select the desirable keyboard layout or in WINDOWS entry “Control” then pops “Keyboard” to select country at “language” item. For details, please refer to your DOS or WINDOWS user’s manual. Keyboard Speed: By selecting, you can change output speed of scanner to match with host computer.
Keyboard layout Keyboard speed USA 00ഖ Belgium 01 Danish 02 France 03 Germany 04 Italian 05 Portuguese 06 Spanish 07 Swedish 08 Switzerland 09 UK 10 Latin American 11 0-8 00-08 0 : high clock rate 01ഖ 8 : low clock rate Disable 00 Enable 01ഖ Alphabetic key 00ഖ Numeric keypad 01 Function key Numeric key (Num lock state only) Alt+Keypad 02 Exit 12
Keyboard wedge Caps Lock: By selecting Caps Lock or No Caps Lock, scanner can get Caps Lock status. Power-on simulation: All of the PCs check the keyboard status during power-on selftest. It is recommended to Enable function if you are working without keyboard installation. It simulates keyboard timing and pass keyboard present status to the PC during power-on. Inter-character delay: This delay is inserted after each data characters transmitted.
Program Option Bar Code Option Alphanumeric Entry Caps lock”ON” 00 Caps lock”OFF” 01ഖ Disable 00ഖ Enable 01 00-99 msec 00-99 Caps lock Power-on simulation 02ഖ Inter-character delay 00-99 10 msec 00-99 10ഖ Block transmission delay Exit 14
RS-232 CTS: Clear To Send (Hardware Signal) RTS: Request To Send (Hardware Signal) Xon: Transmit On (ASCII Code 1116) Xoff: Transmit Off (ASCII Code1316) Flow control: None-The communication only uses TxD and RxD signals without regard for any hardware or software handshaking protocol. RTS/CTS-If the scanner wants to send the barcode data to host computer, it will issue the RTS signal first, wait for the CTS signal from the host computer, and then perform the normal data communication.
Program Option Bar Code Option Alphanumeric Entry Flow control None 00ഖ RTS/CTS 01 Xon/Xoff 02 ACK/NAK 03 00-99 (msec) 00-99 00ഖ Inter-character delay 00-99 (10 msec) 00-99 00ഖ Block transmission delay 00-99 (100 msec) 00-99 20ഖ Response delay Exit 16
Program Option Bar Code Option Alphanumeric Entry Baud rate Parity 300 BPS 00 600 BPS 01 1200 BPS 02 2400 BPS 03 4800 BPS 04 9600 BPS 05ഖ 19200 BPS 06 38400 BPS 07 None 00ഖ Odd 01 Even 02 8 bits 00ഖ 7 bits 01 One bit 00ഖ Two bits 01 Data bit Stop bit Exit 17
Wand Emulation Bar/space polarity: High/low- Black will be transmitted as a high voltage level (+5) and space as low level (0V). Low/high- Black will be transmitted as a low voltage level (0V) and space as high level (+5). Initial polarity: You must make sure what is Initial polarity of your wand decode device in stand-by (idle). So, initial signal state as a High voltage level (+5) or Low voltage level (0V).
Wand Emulation Output speed: This setting is same as serial transmission baud rate, and it must be approbated your wand decode resolution. The unit of speed is a width of minimum narrow bar. Margin delay: It is a timer of zone like space zone of barcode label margin. The width of margin time will be added before and after in each barcode data automatically when it is transmitted. Transmit delay: It is a delay time between barcode data output. It is the same as Block transmission delay of keyboard wedge.
00ഖ Reserved 00ഖ Reserved 00-99 (10 pixel) 00-99 15ഖ Margin delay 00-99 (10 msec) 00-99 30ഖ Transmit delay Exit 20
Scan Scanning mode: Good-read off-The trigger button must be pressed to activate scanning. The light source of scanner stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed. Momentary-The trigger button acts as a switch. Press button to activate scanning and release button to stop scanning. Alternate-The trigger button acts as a toggle switch. Press button to activate or stop scanning.
Program Option Bar Code Option Alphanumeric Entry Scanning mode Good-read off 00 Momentary 01ഖ Alternate 02 Timeout off 03 Continue 04 01-99 (second) 00-99 10ഖ Stand-by duration 01-99 (10 msec) 01-99 50ഖ Same barcode delay time Double confirm 00-99 00-09 (00: no double 00ഖ confirm) Exit 22
Scan Multi field scan: The scanner can be read many sets of barcode data on the same scanning line at the same time, even if they are different kinds of barcode symbology. Global min./max. code length: Global Minimum and Maximum length can be set to qualify data entry. The length is defined as the actual barcode data length to be sent. Label with length exceeds these limits will be rejected.
Disable 00ഖ Enable 01 00-63 00-63 Multi field scan 04ഖ Global min. code length 00-63 04-63 63ഖ Global max.
Indication Power on alert: After power-on the scanner it will generate an alert signal to indicate a successful self-test. LED indication: After each successful reading, the LED above the scanner will light up to indicate a good barcode reading. Buzzer indication: After each successful reading, the scanner will beep buzzer to indicate a good barcode reading, and its Beep loudness, Beep tone freq. and Beep tone duration are adjustable. Beep loudness/Beep tone freq.
Program Option Bar Code Option Alphanumeric Entry Disable 00 Enable 01ഖ Disable 00 Enable 01ഖ Disable 00 Enable 01ഖ 00-07 00-07 Power on alert LED indication Buzzer indication 07ഖ Beep loudness 00-99 (100Hz) 00-99 26ഖ Beep tone freq.
UPCA Read: Format Leading Data Digits Check Zero (11 Digits) Digit Check-sum transmission: By setting Enable, checks sum will be transmitted. Truncate leading/ending: The leading or ending digits of barcode data characters can be truncated when these values are set to non-zero. It will beep instead of reading anything when the truncate value is more than the barcode data digits or the value of Truncate Leading is overlapped with that of the Ending. The maximum value of truncate digits is 15.
Disable 00 Enable 01ഖ Disable 00 Enable 01ഖ 00-64 00-64 Check-sum verification Check-sum transmission 64ഖ Max.code length 00-64 00-64 01ഖ Min.
UPCA Supplement digits: The Supplement digits barcode is the supplemental 2 or 5 characters for WPC code. Format Leading Data Digits Check Zero (11 Digits) Supplement Digits Digit 2 or 5 or UCC / EAN 128 Truncate Leading zero: The leading “0” digits of UPCA data characters can be truncated when the function is enabled.
UPCE Read: Format Leading Data Digits (6 Check Zero Digits) Digits Check-sum verification: The checksum of EAN-13 is optional and made as the sum of the numerical value of the data digits. Check-sum transmission: By setting Enable, checks sum will be transmitted.
UPCE Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Supplement digits: Format Leading Zero Data Digits Check (6 Digits) Digit Supplement Digits 2 or 5 or UCC/EAN 128 Truncate Leading zero: Refer to Truncate Leading zero of UPCA. Expansion: The expansion function is used only for UPCE and EAN-8 code reading.
0-15 00-15 00ഖ Truncate ending 00-ffH ASCII 00-ffH code < E >ഖ 00-44 00-44 Code ID setting 00ഖ Insert group selection Supplement digits None 00ഖ 2 digits 01 5 digits 02 UCC/EAN 128 03 Auto detection 04 Disable 00ഖ Enable 01 Disable 00ഖ Enable 01 Truncate Leading zero Expansion Exit 32
EAN-13 Read: Format Data Digits (12 Digits) Check Digits Check-sum verification: The checksum of EAN-13 is optional and made as the sum of the numerical value of the data digits. Check-sum transmission: By setting Enable, checks sum will be transmitted. Max./Min. code length: Each symbology has own Max./Min. Code Length. They can be set to qualify data entry. If their Max./Min. Code Length is zero, the Global Min./Max. Code Length is in effect.
Disable 00 Enable 01ഖ Disable 00 Enable 01ഖ 00-64 00-64 Check-sum verification Check-sum transmission 64ഖ Max.code length 00-64 00-64 01ഖ Min.
EAN-13 Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Supplement digits: Format Data Digits Check (12 Digits) Digits Supplement Digits 2 or 5 or UCC / EAN 128 ISBN/ISSN: The ISBN (International Standard Book Number) and ISSN (International Standard Serial Number) are two kinds of barcode for book and magazines. The ISBN is 10 digits with leading “978” and the ISSN is 8 digits with leading “977” of the “EAN-13” symbobolgy.
Program Option Bar Code Option Alphanumeric Entry 00-ffH ASCII 00-ffH code < F >ഖ 00-44 00-44 Code ID setting 00ഖ Insert group selection Supplement digits None 00ഖ 2 digits 01 5 digits 02 UCC/EAN 128 03 Auto detection 04 Disable 00ഖ Enable 01 ISBN/ISSN conversion Exit 36
EAN-8 Read: Format Data Digits Check (7 Digits) Digits Check-sum verification: The checksum of EAN-8 is optional and made as the sum of the numerical value of the data digits. Check-sum transmission: By setting Enable, checks sum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of EAN-13. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA Insertion group selection: Refer to Insertion group selection of UPCA.
Disable 00 Enable 01ഖ 00-64 00-64 Check-sum transmission 64ഖ Max.code length 00-64 00-64 01ഖ Min.
EAN-8 Supplement digits: Format Data Digits Check (7 Digits) Digits Supplement Digits 2 or 5 or UCC/EAN 128 Truncate Leading zero: Refer to Truncate Leading zero of UPCE. Expansion: Refer to Expansion of UPCE.
Code 39 Read: Format Start Data Digits Checksum End “့” ( Variable) (Optional) “့” Check-sum verification: The checksum of Code-39 is optional and made as the sum module 43 of the numerical value of the data digits. Check-sum transmission: By setting Enable, checksum and will be transmitted.
Code 39 Max./Min. code length: Each symbology has own Max./Min. Code Length. They can be set to qualify data entry. If their Max./Min. Code Length is zero, the Global Min./Max. Code Length is in effect. The length is defined as to the actual barcode data length to be sent. Label with length exceeds these limits will be rejected. Make sure that the Minimum length setting is no greater than the Maximum length setting, or otherwise all the labels of the symboblogy will not be readable.
00-64 00-64 00ഖ Max. code length 00-64 00-64 00ഖ Min.
Code 39 Append: This function allows several symbols to be concatenates and be treat as one single data entry. The scanner will not transmit the embedded appending code (space for Code-39). If Enable and other symbols were read again with the appended code, then codes will be transmitted without Code ID, Preamble and Prefix. When a symbol was decoded without the appended code, the data will be transmitted without Code ID and Prefix, but the Postamble Suffix codes are appended.
Interleaved 2 of 5 Read: Format Data Digits Checksum (Variable) (Optional) Check-sum verification: The checksum is made as the sum module 10 of the numerical values of all data digits. Check-sum transmission: By setting Enable, checksum and will be transmitted.
Interleaved 2 of 5 Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option Bar Code Option Alphanumeric Entry 00-64 00-64 00ഖ Max. code leading 00-64 00-64 00ഖ Min.
00-ffH ASCII 00-ffH code < i >ഖ 00-44 00-44 Code ID setting 00ഖ Insert group selection Exit 46
Industrial 2 of 5 Read: Format Data Digits Checksum (Variable) (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option Bar Code Option Alphanumeric Entry Disable 00ഖ Enable 01 00-64 00-64 Read 00ഖ Max. code length 00-64 00-64 00ഖ Min.
0-15 00-15 00ഖ Truncate leading 0-15 00-15 00ഖ Truncate ending 00-ffH ASCII 00-ffH code < i >ഖ 00-44 00-44 Code ID setting 00ഖ Insert group selection Exit 48
Matrix 2 of 5 Eur Read: Format Data Digits Checksum (Variable) (Optional) Checksum Verification: The checksum is made as the sum module 10 of the numerical values of all data digits. Checksum Transmission: By setting Enable, checksum and will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA.
Disable 00ഖ Enable 01 Checksum Transmission 00-64 00-64 00ഖ Max. code length 00-64 00-64 00ഖ Min.
Codabar Read: Format Start Data Digits (Variable) Checksum (Optional) End Checksum Verification: The checksum is made as the sum module 16 of the numerical values of all data digits. Checksum Transmission: By setting Enable, checksum and will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA.
Disable 00ഖ Enable 01 00-64 00-64 Checksum Transmission 00ഖ Max. code length 00-64 00-64 00ഖ Min.
Codabar Insertion group selection: Refer to Insertion group selection of UPCA. Start/End type: The Codabar has four pairs of Start/End pattern; you may select one pair to match your application. Start/End Transmission: Refer to Start/End Transmission of Code 39.
Code-128 Read: Format Data Digits Checksum (Variable) (Optional) Checksum Verification: The checksum is made as the sum module 103 of all data digits. Checksum Transmission: By setting Enable, checksum and will be transmitted.
Code-128 Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Format: The Code-128 can be translated to UCC/EAN-128 format if it starts with FNC1 character. The first FNC1 will be translated to “]C1”,and next to be a field separator code as (1D16).
0-15 00-15 00ഖ Truncate leading 0-15 00-15 00ഖ Truncate ending 00-ffH ASCII 00-ffH code < # >ഖ 00-44 00-44 Code ID setting 00ഖ Insert group selection Standard 00ഖ UCC/EAN-128 01 Disable 00ഖ Enable 01 00-ffH ASCII 00-ffH code < # >ഖ 00-ffH ASCII 00-ffH code 1DHഖ Format Append UCC/EAN-128 ID setting Field separator code Exit 56
Code-93 Read: Format Data Digits Checksum1 Checksum2 (Variable) (Optional) (Optional) Checksum Verification: The checksum is made as the sum module 47 of the numerical values of all data digits. Checksum Transmission: By setting Enable, checksum and will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA.
Disable 00ഖ Enable 01 00-64 00-64 Checksum Transmission 00ഖ Max. code length 00-64 00-64 00ഖ Min.
Code-11 Read: Format Data Digits Checksum1 Checksum2 (Variable) (Optional) (Optional) Checksum Verification: The checksum is presented as the sum module 11 of all data digits. Checksum Transmission: By setting Enable, checksum1 and checksum2 will be transmitted upon your selected checksum verification method. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA.
Disable 00ഖ Enable 01 00-64 00-64 Checksum Transmission 00ഖ Max. code length 00-64 00-64 00ഖ Min.
MSI/plessey Read: Format Data Digits Checksum1 Checksum2 (Variable) (Optional) (Optional) Checksum Verification: The MSI/Plessey has one or two optional checksum digits. The checksum is presented 3 kinds of method Mod10, Mod10/10 and Mod 11/10. The checksum1 and checksum2 will be calculated as the sum module 10 or 11 of the data digits. Checksum Transmission: By setting Enable, checksum1 and checksum2 will be transmitted upon your selected checksum verification method. Max./Min.
Disable 00ഖ Enable 01 00-64 00-64 Checksum Transmission 00ഖ Max. code length 00-64 00-64 00ഖ Min.
UK/plessey Read: Format Data Digits Checksum1+2 (Variable) (Optional) Checksum Verification: The UK/Plessey has one or two optional checksum digits. The checksum1 and checksum2 will be calculated as the sum module 10 or 11 of the data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA.
Disable 00ഖ Enable 01 00-64 00-64 Checksum Transmission 00ഖ Max. code length 00-64 00-64 00ഖ Min.
Telepen Read: IATA (International Air Transport Association). Checksum Verification: The checksum is presented as the sum module 10 or 11 of the data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA.
00-64 00-64 00ഖ Max. code length 00-64 00-64 00ഖ Min.
Standard 2 of 5 Read: Format Data Digits Checksum1 (Variable) (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option Bar Code Option Alphanumeric Entry Disable 00ഖ Enable 01 00-64 00-64 Read 00ഖ Max. code length 00-64 00-64 00ഖ Min.
0-15 00-15 00ഖ Truncate leading 0-15 00-15 00ഖ Truncate ending 00-ffH ASCII 00-ffH code < i >ഖ 00-44 00-44 Code ID setting 00ഖ Insert group selection Exit 68
China Post Read: Format Data Digits Checksum1 (Variable) (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option Bar Code Option Alphanumeric Entry Disable 00ഖ Enable 01 00-64 00-64 Read 11ഖ Max. code length 00-64 00-64 11ഖ Min.
0-15 00-15 00ഖ Truncate leading 0-15 00-15 00ഖ Truncate ending 00-ffH ASCII 00-ffH code < t >ഖ 00-44 01-44 Code ID setting 00ഖ Insert group selection Exit 70
Italian Pharmacode Read: Format Data Digits Checksum1 (Variable) (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Leading “A”: If this function is enabled, each prefix of data shall be A.
00-64 00-64 09ഖ Min.
String setting Prefix characters: Up to 22 ASCII characters may be sent before data digits. Prefix Data Digits Suffix Suffix characters: Up to 22 ASCII characters may be sent after data digits. Preamble/ Postamble characters: They are appended to the data automatically when each barcode is decoded. Example: Add a prefix/suffix or preamble/postamble for all symbologies. In this example, you are sending a $ symbol as a prefix for all symbologies.
None 00ഖ 1-22 characters 00-ffH ASCII code Preamble characters setting None 00ഖ 1-22 characters 00-ffH ASCII code Postamble characters setting None 00ഖ 1-22 characters 00-ffH ASCII code Insert G1 characters setting None 00ഖ 1-22 characters 00-ffH ASCII code Insert G2 characters setting None 00ഖ 1-22 characters 00-ffH ASCII code Insert G3 characters setting None 00ഖ 1-22 characters 00-ffH ASCII code Insert G4 characters setting Exit 74
String setting Insert G1/G2/G3/G4 character setting: The scanner offer 4 positions and 4 characters to insert among the symbol. Example: Barcode “1 2 3 4 5 6”. Output- Barcode “1 2 A B 3 4 C D 5 6”. Steps: 1) Scan Programming and Insert G1 characters setting barcode. 2) Use the ASCII code table to find the value of Aඎ41,Bඎ 42. 3) Scan 4, 1 and 4, 2 from the barcode on the fold out back page. 4) Scan Finish from the barcode on the fold out page. 5) Repeat the same procedure in Insert G2 characters setting.
None 00ഖ 1-22 characters 00-ffH ASCII code Insert G3 characters setting None 00ഖ 1-22 characters 00-ffH ASCII code Insert G4 characters setting Exit 76
Transmission Preamble transmission: By setting Enable, Preamble will be appended before the data transmitted. Postamble transmission: By setting Enable, Postamble will be appended after the data is transmitted. Insert data group 1-4 position: The scanner offers 4 positions to insert among the symbol. The position default value is “00” to indicate no character insertion. Beside, make sure insertion positions are not greater than the symbols; otherwise the insertion data is not effective.
00-64 00-64 (00: no insertion) 00ഖ 00-64 00-64 (00: no insertion) 00ഖ 00-64 00-64 (00: no insertion) 00ഖ 00-64 00-64 (00: no insertion) 00ഖ Before code data 00ഖ After code data 01 Insert data group 1 position Insert data group 2 position Insert data group 3 position Insert data group 4 position Code ID position Exit 78
Transmission Code ID transmission: If your application is needed to transmit Code ID, you must set this to Proprietary ID or AIM ID. Code length transmission: A number of data digits can be transmitted before the code data when Enable is selected. The total length of the barcode is the number of barcode data except Truncate Leading/Ending Digits. And the length is a number with two digits.
Disable 00ഖ Enable 01 Disable 00ഖ Enable 01 Disable 00ഖ Upper case 01 Lower case 02 Code length transmission Code name transmission Case conversion *For barcode data only Exit Format of barcode data transmission: Prefix Name Preamble ID Code Barcode Length data Insert groups 80 ID Postamble Suffix
7HVW &KDUW CODABAR-PARA CODE-11 PARA CODE-128 PARA CODE-39 PARA CODE-93 PARA EAN-13 PARA 81
PDF-417 STANDRAD-25 PARA CODE-16K EAN-8 PARA INDUSTRIAL-25 PARA UPCE PARA 82
INTERLEAVED-25 PARA MATRIX 25 PARA MSI/PLESSEY PARA UPCA PARA UK/PLESSEY PARA 83
ASCII Code Table 1RWH )RU NH\ERDUG ZHGJH RQO\ / + 1XOO 18/ '/( 8S ) 62+ '& 'RZQ ) 67; '& /HIW ) (7; '& 5LJKW ) (27 '& 3J8S ) (14 1$. 3J'Q ) $&.
Parameter Setting List Program Barcode standard parameter setting list If you wish to display the current configuration of your LGZ7225, scanner over the host terminal/computer scan the Barcode standard parameter setting list bar code.
Firmware version list If you wish to display the firmware version, scan the Firmware version list. WARNING: Default value initialization If you wish to return theLGZ 7225 to all the factory default settings, scan the Default value initialization bar code.
0 A 1 B 2 C 3 D 4 E 5 F 6 7 8 Finish 9 97 87
