MINI SPEED DOME CAMERA 10X Mini Speed Dome Camera Instruction Manual Rev 1.01 dated on Dec.
CONTENTS Warning & Caution 3 What’s in the Box? 3 General Features Names of Each Part 4 5 Installation A. Connection Methods B. Ceiling Mount Type 6 7 C. Embedded Mount Type Quick Operating Keys Diagnostic 8 9 OSD Menu Setting A. OSD Menu Table 10 B. DOME SET 11 C. CAMERA SET 16 D. PRESET 18 E. AUTO SCAN 19 F. TOUR SET 20 G. PRIVACY SET 21 H. PATTERN SET 22 I. ALARM SET 23 J. SECTOR SET 24 DIP Switch Setting A. ID Setting (DIP SW1) B.
WARNING & CAUTION If you fail to read this information and handle the product incorrectly, death or serious injury may occur. The unit should be installed by the trained Personnel. Always stop using when the product emits smoke or abnormal heat. Never install the product in area exposed to water, oil or gas.
GENERAL FEATURES 100X Zoom Mini Speed Dome Quick Operation Keys 10X Optical Zoom with 10X digital zoom This camera provides quick functional keys in other to be easily controlled by any other controller or DVR. ±0.02° dome system accuracy with 1/4 micro step Various Surveillance Functions With 0.
NAMES OF EACH PAR T 1. Surface Mount Adaptor 2. Cap Screw ( PT3/4 , 2EA ) 3. Dip Switch 4. Terminal Block 5.
INSTALLATION A. CONNECTION MATHOD A-1 1. 2. 3. 4. 5. 6. Loose the screws on the domes cover and remove it from the base. (Screws won’t be removed) Loose the screws which connect mount cover and Main base and separate dome cover from the main base. (Screws won’t be removed) Connect power (DC12V 1.5 A) to Power and GND. Connect video to Video and GND. Connect communication cable to RS-485 connectors. Connect alarm cable to GND like 1 and GND, 2 and GND, 3 and GND, 4 and GND. (You can use both N.O / N.
INSTALLATION B. CEILING MOUNT TYPE 1. Fix the surface mount adaptor with 4pcs of screws on the place where you want to install. (FIG.4) 2. When you use pipe, please note the standard size of pipe. (FIG.5) 3. You can re-assemble the domes.
QUICK OPERATING KEYS This dome provides three protocols mainly as Pelco D, Pelco P. These protocols are able to use with other DVR or Controller if the equipment has the above protocols. Default setting of this dome is Pelco D / P (auto detection) with 2400 bps (baud rate). As the merit of this product, it has lots of function keys to support the following functions. 1-64 + preset and 100~200 + preset are used for preset and 65-99 + preset used for functions.
QUICK OPERATING KEYS DIAGNOSTIC When Power on, DIAGONOSTIC is operated. The following messages are displayed on the monitor. CAMERA ID : 001 BAUD RATE : 2400 BPS WAITING……… A. PAN ORIGIN TEST OK TILT ORIGIN TEST OK TX CONNECTION TEST OK CAMERA COMM TEST OK Pan Origin Test Zero point of Pan is founded after Panning test. B. Tilt Origin Test Zero point of Tilt is founded after Tilting test. C.
EXIT SECTOR ALARM PATTERN PRAVACY TOUR AUTO SCAN CAMERA SET DOME SETUP MAIN MENU WB MODE PIC FLIP BLC : OFF : FAST : DISABLE AUTO FLIP ZOOM SPEED ALARM EXIT SAVE AND EXIT EXIT : 01 : 01 : 10 : 200°/S TOUR STEP PRESET NO DWELL TIME SPEED EXIT [PRIVACY CLEAR] UPGRADED DATE: 06.28,06 COORDINATE:ON/OFF [PREVIOUS PAGE] [PREVIOUS PAGE] [SECTOR CLEAR] FIRMWARE VER.:2.
OSD MENU SETTING To enter OSD Menu, press the button 95 + PRESET. MAIN MENU DOME SETUP CAMERA SET AUTO SCAN TOUR PRAVACY PATTERN ALARM SECTOR EXIT * Use the joystick “up down” to move the position and “left right” to make selection B. Dome Setup In order to enter Dome setup, the joystick move to right direction when cursor on dome setup.
OS D MENU S ETTING B-2. DOME SET - RECOVER This feature allows the dome to work from the last setting before you use the dome manually (Auto scan, group tour, preset, pattern or sectors), after the set time, even power shut down and it turns on again. Recover time can be programmed from 15 second to 99 seconds. The default setting is OFF. B-3. DOME SET - MANUAL SPEED Manual Speed of Pan/Tilt is selectable from 100°/sec up to 150°/sec. The default setting is 100°/sec B-4.
OSD MENU SETTING B-8-2. DOME SET – [NEXT PAGE] – [PASSWORD] To enter this page to set a password, move joystick to the right direction. The password must be set by preset number from 001 to 255 (Default 99) A. OSD MAIN MENU TABLE (PAGE 14) default setting is BLANK. ENTER PASSWORD BY ENTERING PRESET CODE PASSWORD *** CONFIRM *** Press any number from 001~255 with preset button on password blank and again it on confirm blank.
OSD MENU SETTING OSD DISPLAY CAMERA ID : PRESET ID : SECTOR ID : COORDINATE : [PREVIOUS PAGE] OFF OFF OFF ON DEFAULT SETTING B-8-4. DOME SET – [NEXT PAGE] – [SYSTEM STATUS] This page shows the information of this camera. SYSTEM STATUS PROTOCOL : BAUD RATE : FIRMWARE VER. : UPGRADED DATE : CAMERA MODULE : [PREVIOUS PAGE] PELCO D, P 2400 BPS 1.05 06.12.
OSD MENU SETTING - To clear memorize any data, move joystick to the right direction when cursor is on each item. TOUR CLEAR TOUR CLEAR ARE YOU SURE? YES NO Press FOCUS NEAR button when the cursor is at YES in order to clear memorized data. Then flickered each item such as tour, preset, sector and so on is displayed on the monitor about 2~3 seconds. After this process, the menu is returned to the previous page. * [PRESET CLEAR], [SECTOR CLEAR], [PRIVACY CLEAR], [PATTERN CLEAR] are same as [TOUR CLEAR].
OSD MENU SETTING C. CAMERA SET CAMERA SET FLICKER MIRROR APERTURE D ZOOM WB MODE PIC FLIP BLC D/N MODE DSS MODE EXIT : : : : : : : : : CAMERA SET OFF OFF 10 OFF AWB MODE OFF OFF AUTO OFF FLICKER BLC EXIT <10X > : OFF : OFF < 3X > C-1. CAMERA SET - FLICKERLESS Flickerless feature is selected between 50Hz and 60Hz. PAL: 50Hz). The default setting is OFF (NTSC: 60Hz / Set flicker mode ON when power source is in discord with frequency. The default setting is OFF C-2.
OSD MENU SETTING C-6. CAMERA SET – PIC FLIP Picture flip feature provides the top and down exchanged picture image horizontally. Move joystick to the right or left direction to select OFF/ON. The default setting is OFF. C-7. CAMERA SET – BLC (Back Light Compensation) The default setting is OFF and BLC modes can be OFF/ON. OFF – Backlight compensation is not activated. ON – Back light compensation is activated. This function can be recalled by pushing 93 + preset button. C-8.
OSD MENU SETTING D. PRESET SET To enter PRESET SET, move joystick to the right direction. PRESET SET PRESET NO :001 PRESET ID :PRESET001------PAN :XXX.XX TILT : XXX.XX SAVE EXIT D-1. DEFAULT SETTING PRESET – PRESET NO. Up to 165 numbers of preset positions are available. Move joystick to the right or left direction to select preset no. D-2. PRESET – PRESET ID To set preset ID, select up to 16 characters using Joystick to the left or right.
OSD MENU SETTING E. AUTO SCAN SET * 66 + preset button is working as AUTO SCAN after setting. AUTO SCAN SET START ANGLE END ANGLE DIRECTION ENDLES SPEED DWELL TIME SAVE AND EXIT EXIT : : : : : : XXX.X.XX.X XXX.X.XX.X CW OFF 10°/S 03 DEFAULT SETTING E-1. AUTO SCAN – START ANGLE To set start angle, press FOCUS FAR button then move joystick to the starting angle which is needed memorized. To press FOCUS FAR button again is to escape. E-2.
OSD MENU SETTING F. TOUR SET 8 Programmable tours can be set and each tour is available to set up to 64 preset steps. After setting the data to the each tour group, 71~78 + preset buttons are working as group tour # 1~8 TOUR SET TOUR NO TOUR TITLE TOUR STEP PRESET NO. DWELL TIME SPEED SAVE EXIT : : : : : : 01 TOUR01□□□□□□□□□□ 01 01 03 200°/S DEFAULT SETTING F-1. TOUR SET – TOUR NO. Max. 8 group tour no. set by the joystick are available. F-2.
OSD MENU SETTING G. PRIVACY SET 4 Privacy masking zones are available to block out areas of security. PRIVACY SET PRIVACY NO DISPLAY ACTION SAVE EXIT : 01 : OFF : MOVE DEFAULT SETTING G-1. PRIVACY SET – PRIVACY NO. It provides up to 4 privacy masking zones G-2. PRIVACY SET – DISPLAY. Move joystick to the right or left direction to set ON in order to show the selectable block in the center of the monitor. This block appears as a translucent square with blue color after set ON.
8 programmable patterns are available with 16 characters of title. After setting the data to each pattern # 1~8, 81~88+ preset buttons are working as Pattern # 1~8. PATTERN SET PATT NO : 01 PATT TITLE: PATTERN01□□□□□□□ DATA FILL : 0% SAVE EXIT DEFAULT SETTING H-1. PATTERN SET –PATT NO. Up to 8 programmable user-defined patterns set by the joystick are available. H-2. PATTERN SET –PATT TITLE To set PATTERN TITLE, select up to 16 characters using Joystick to the left or right.
4 Alarm inputs are available and each alarm is activating to presets, group tours or patterns. ALARM SET ALARM NO : 01 ALARM INPUT: OFF ALARM ACT : 001 SAVE EXIT DEFAULT SETTING I-1. ALARM SET – ALARM NO. Up to 4 alarms are selectable by using joystick to the right direction when cursor is on ALARM NO. I-2. ALARM SET – ALARM INPUT Input alarm ways provide two different ways as NC (Normal Close) or NO (Normal Open) The default setting is OFF I-3.
OSD MENU SETTING J. SECTOR SET Up to 8 programmable sectors are available with 16 characters. This feature is useful to memory the certain location such as parking zone or so on. When camera goes through this area, it shows the letter you memorized. SECTOR SET SECTOR SECTOR SECTOR SECTOR SAVE EXIT Start Position NO : 01 ID: SECTOR01□□□□□□□□ START: XXX.X.XX.X END : XXX.X.XX.X End Position DEFAULT SETTING J-1. SECTOR SET – SECTOR NO. Up to 8 programmable sectors set by the joystick are available. J-2.
DIP SWITCH SETTING A-1. DIP SW SETTING st th Mini Speed Dome camera provides up to 63 cameras ID and it’s an adjustable ID with 1 ~6 of Dip switch. Open the camera case to set ID using DIP SW1. * Factory default: Camera ID = 1, PELCO-D Baud Rate: 2400bps Termination Baud rate Protocol ID Set A-2.
DIP SWITCH SETTING A-3. PROTOCOL th th 7 ~8 dip switches are used for Protocol Setting. Factory Default: Pelco-D or Pelco-P (Auto detection) DIP SW1- 7 DIP SW1- 8 OFF OFF Pelco-D or Pelco-P A-4. BAUD RATE SETTING th The 9 Dip Switch is used for BAUD RATE setting. DIP SW can be changeable to 2400bps, 9600bps. Factory Default: 2400bps. DIP SW1 9th BAUD RATE OFF 2400 ON 9600 . A-5. 485 TERMINATIONS th 10 Dip Switch is used for 100Ω termination.
TROUBLESHOOTING If you have trouble in operating in your camera, refer to the following. PROBLEM SOLUTION No operating Check if the power supply is DC12V. Check if RS-485 communication cable is connected correctly. Check camera ID setting. Check the termination. No picture Check if all the cables are connected correctly. Check if the monitor is adjusted correctly. Check if video signal line is cut. Dark screen Adjust the monitor status.
SPECIFICATIONS MODEL PAN /TILT 10X A/F CAMERA MODULE Pan Rotation Angle Manual Pan Speed Preset Tilt Rotation Angle Manual Tilt Speed Preset System Accuracy Presets Group Tour FUNCTIONS POWER OTHERS Auto scan Pattern Privacy Zone Sector Password Protection Alarm Input Alarm Actions Auto Flip OSD Menu Communication Protocol Consumption (12V DC) Consumption (24V AC) Power Supply(12V DC) Power Supply(24V AC) Construction Dimensions Weight Motor Type Micro Steps Storage Temperature Operating Temperature
DIMENSIONS 29
General Information Limited Warranty At Discount Security Cameras (DSC) we take pride in offering only the highest quality reliable products. In the rare event that a defect does occur we offer the following warranty: All products are warranted by Discount Security Cameras for 1 year from date of purchase, except for Clearance items, which are warranted for 30 days. If a product is defective we will repair or replace it. The customer is responsible for the shipping to send the product to us.
Return Policy Merchandise may be returned for a refund or exchange for 15 days from day of receipt as long as the equipment is still in "as new" condition. A 15% restocking fee may apply. Shipping costs are not refundable (unless the product is defective - see warrantee below). "As New" means that all items must be undamaged and in their original cartons and packaging along with all accessories, documentation, and parts. No wires or pigtails can be cut. The product exterior must be intact and unmarked.
