Specifications

ManualsBrandsOptoma ManualsProjector MountsBM-3300ST

Read these instructions carefully before installing your equipment.

Install the mount in a suitable location using fixings which are appropriate for the wall material and

structure. Consult a qualified builder if you are in any doubt as to the structural integrity of the wall.

Use all available fixing points.

Do not attempt to alter or modify any part of the wall mount or it's attachments.

Do not use if any parts are broken or appear to be damaged.

Tighten all bolts and fixings securely. Only use fixings provided with this bracket.

Do not mount your projector near to sources of heat or moisture.

Always have a minimum of two persons to install the projector and the mount.

MOUNTING INSTRUCTIONS FOR

SHORT THROW PROJECTOR MOUNT

MODEL No. BM-3300ST

FN. OPTBM3300ST

Max Weight Loading 33Ibs

Projector Mount Assembly Kit

D - M6 x 12mm

A - M8 / M6 washer

C - M8 x 16mm

B - M8 nut

x8/x3

Ÿ Assemble projector mounting plate to the 16" stud adapter plate using x4

M8 washers (A) & x4 M8 nuts (B)

Ÿ For ease of installation mount bracket on wall using position 1 and mark

other positions using a spirit level. Remove fixing from position 1, remove

bracket and drill other positions

Ÿ Use Fixings suitable for your type of wall construction.

Ÿ Use All available fixing points.

Ÿ If in any doubt of the suitability of the wall, it's construction or what type of

fixings to use, consult a qualified builder or installer.

Assemble wall plate & attach assemble to wall.

Secure Boom Arm To Wall Plate

Tether Point

CAUTION NOTE!

This mount is designed to take projectors up to a weight

of 33Ibs. For safety reasons the mount has been tested

with a dead weight loading of 165Ibs. It is recommended

that if the installation is at risk of being subjected to

greater loads then you should additionally tether the

mount to the ceiling using the tether point (highlighted

below). The tether point uses an M6 thread which can

accept any M6 fixing such as an eye bolt or hook.

Summary of content (4 pages)

PAGE 1
Projector Mount Assembly Kit Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ MOUNTING INSTRUCTIONS FOR SHORT THROW PROJECTOR MOUNT MODEL No. BM-3300ST FN. OPTBM3300ST Max Weight Loading 33Ibs 1 Read these instructions carefully before installing your equipment. Install the mount in a suitable location using fixings which are appropriate for the wall material and structure. Consult a qualified builder if you are in any doubt as to the structural integrity of the wall. Use all available fixing points.
PAGE 2
3 Adjust Length Of Mount First remove Transit screw Re-insert after adjustment C x2 B x3 4 Attaching Optoma 212/305/306/605/610ST Projectors a Optoma 212ST, 305ST, 306ST Series Fixing Kit Optoma 212ST D - M3 x 20mm Optoma 305ST, 306ST D - M4 x 20mm x3 E - Mounting Bobbin x3 F - 2.
PAGE 3
4 b 5 Fine Adjust Position Gx2 c 4 c The following adjustments (labelled below) can be made to fine tune position to correct any discrepancy in the installation or mounted surface; a To fine tune the length and tilt of the mount, loosen bolts, slide mount to required position and re-tighten bolts. b To fine tune the level of the projector use the four adjustment thumb wheels on the spring loaded cradle. Do not fully unwind the thumb wheels.
PAGE 4
Specifications; - 535mm to 1350mm (Approx dependent on fixing positions) Adjustment - 100mm Fine length adjustment +/- 5° Tilt Adjustment with integral level 4-point vernier adjustment tilt and yaw 100mm Height Adjustment at wall Compatibility - Optoma ZX212ST, ZW212ST, X305ST, W305ST, X306ST & W306ST 214.