BX-AL133 Anamorphic Lens User’s Manual
User’s Manual BX-AL133 Safety 1. Read and understand instructions and heed warnings before beginning installation. 2. Mount rail securely. The lens is heavy, and requires a secure and stable surface. Fasteners in sheetrock alone are not safe. Reciprocal lens motion can and will work them loose. Use a board, plate, or projector mount fixed to ceiling joists or studs. 3. Anticipate unexpected lens motion. A malfunction can cause the lens to move unexpectedly.
User’s Manual BX-AL133 Introduction Thank you for purchasing the Optoma BX-AL133 anamorphic lens. The lens and motorized sled is outfitted with a custom mechanism designed exclusively for use in a home theater environment. No oil or liquid based lubricants are used to assure the maximum cleanliness of optical components. Both lens and drive will provide years of maintenance free service. The Optoma system is built and tested in the USA with the strictest quality standards and certifications.
User’s Manual BX-AL133 Getting to Know Your System Motorized Sled Status LED Infrared Remote Sensor Reversable Logo Plate Mounting Plate Rail Drive Belt Rail Bearing (X4) Lens Adaptor Plate Pulley Housing Cover Motor Housing Cover Remote IR Sensor Rear Panel View +9V DC In +12V Trigger Out +12V Trigger In 8-Button Remote Control OFF ON LENS OUT LENS IN PANEL OFF PANEL ON SLOW FAST Remote IR Sensor In 16.5V DC Power Supply For more information, please visit our website at: http://www.
User’s Manual BX-AL133 Plan Your Installation The lens assembly may be mounted in one of two ways: 1. To the ceiling or projector mount above the projector 2. To a shelf or table below the projector When attaching the motor assembly to the ceiling, use a board, plate or lens-enabled projector mount that is attached to ceiling joists or studs. Sheetrock embedded fasteners can and will become loose with repeated lens movement, causing the mechanism to fall, resulting in possible severe injury.
User’s Manual BX-AL133 Mounting Sled to Shelf or Ceiling When installing the motorized sled, make sure that you first mark screw locations using only the sled−without the lens and/or the lens bracket in place. Do not rely on fasteners embedded in sheetrock alone. Reciprocal lens movement can and will work them loose and cause the mechanism to fall. Mount the sled on a plate, board, or lens-enabled projector mount affixed to ceiling joists for safety.
User’s Manual BX-AL133 2. Securing the mounting plate Because the mechanism and lens are heavy, make sure the mounting fasteners and surface are extremely secure. Remember that the sled motor will be starting and stopping a heavy weight thousands of times through normal use. Ceiling mounted lenses require a secure surface. Sheetrock anchors alone are insufficient. Secure the mounting bar to a plate, painted board, or lens-enabled projector mount that is securely affixed to the studs or ceiling joists.
User’s Manual BX-AL133 Setup 1. Power up the sled and set LENS IN position Slide the lens into the middle of the sled before powering up. Plug the power adaptor into an AC outlet, then into the back of the unit as illustrated. Using the remote, press the “lens in” button. The lens sled will slowly position itself into the factory default LENS IN position. The edge of the adaptor plate will land about a half-inch from the motor housing side of the sled.
User’s Manual BX-AL133 3. Attaching the lens to the bracket Attach the Optoma BX-AL133 anamorphic lens to the bracket using the plastic knobs supplied with the lens. Adjust the anamorphic lens vertically for correct alignment. When the image is correct, tighten the knobs against the bracket. Using the remote, test run LENS IN and LENS OUT commands. Tighten Knobs 4. Configuring the lens speed The lens has two operating speed modes – FAST and SLOW. Slow is the default from the factory.
User’s Manual BX-AL133 Remote Control and Motor Operation The LED indicator on the sled will glow when the unit is ON, and flash when any button is pressed. It will also flash when the lens is in motion. The LED will be off in standby mode. Buttons: 8-Button Remote Control OFF – Puts the sled in standby mode. ON –Turns the sled from standby to ON. LENS OUT – Commands the lens to move into the LENS OUT position.
User’s Manual BX-AL133 Rear Panel − Triggers and Sensors To use the automatic lens trigger, your projector or scalar must be equipped with a lens trigger and a standard double-ended 3.5 mm (1/8 inch) male mono or stereo jack cable. Simply plug the cable into the projector’s lens trigger jack and into the sled +12V TriggerIn jack. Follow the projector or scalar instructions to configure the lens trigger.
User’s Manual BX-AL133 Cleaning and Maintenance The Optoma BX-AL133 anamorphic lens system is maintenance-free. It will deliver many years of trouble-free service as delivered from the factory. To clean: Lightly blow off any surface debris from the lens. If needed, clean the lens using standard cleaning supplies while the projector is on (be careful not to look directly into the light beam of the projector. Clean the metal components with a damp cloth, make sure not to drip any water into the enclosure.
User’s Manual BX-AL133 Specifications Electrical Characteristics Model Optoma BX-AL133 Motorized Sled Power Supply 110/120v, 50-60 Cycles Power Supply Output 9V DC, 0.5A Operating Voltage 9-18V DC, 0.5-1.5A Operating Current Draw Typical 650mA, max 1.2A Standby Current Draw 60mA Trigger Jack 3.5 mm Mono or Stereo Jack, 12V, Tip Positive Remote IR Jack 2.
User’s Manual BX-AL133 Dimensions 19.675” 4.511” Ø.25” Score Mark (Motor Side) Score Mark (Pulley Side) 2.5” 3.0” 7.705” 5.375” 7.25” 10.842” 8.333” 13.738” 1.079” .25” 3.579” 3.402” 1.52” 5.094” 4.97” 6.921” 5.973” 5.519” For more information, please visit our website at: http://www.OptomaUSA.
User’s Manual BX-AL133 Warranty Optoma Technology Inc. warrants this product to be free of defects in original workmanship and material for a period of twenty-four (24) months from the date of purchased. During this period, a defective unit may be repaired or replaced, at the discretion of Optoma Technology Inc., by returning it in its original packaging with a copy of your receipt.
User’s Manual BX-AL133 Addendum: Adapter Plate This attachment plate is designed to be installed onto a ceiling mounted projector. The location or orientation of the ceiling mount does not need to change.
User’s Manual BX-AL133 4. INSTALL CHAINS. Hold the chain to the ceiling so that one end of the chain hangs just above one of the installed plate hooks. Mark the ceiling location and repeat for the other chain hook. Procure and install the ceiling hooks at those locations small enough to accept a chain end, and strong enough when installed to support approximately 40 pounds (or more). The type of hook and method of installation may depend on the type of ceiling you have.
User’s Manual BX-AL133 Addendum: The Finished Product For more information, please visit our website at: http://www.OptomaUSA.
#ANADA +ENNEDY 2OAD -ISSISSAUGA /. , : ! #ANADA TEL &AX WWW.Optoma.com USA 715 Sycamore Drive Milpitas, CA 95035, USA Tel: 408-383-3700 &AX WWW.OptomaUSA.com Optoma Technology, Inc. 715 Sycamore Drive, Milpitas CA 95035 TEL s &AX &OR MORE INFORMATION PLEASE VISIT WWW.Optoma.com. Specifications subject to change without notice. Copyright 2007 Optoma Technology, Inc.
