Digital Signage Monitor Sign Show 7POP Operation Manual Thank you for your purchase Before using this device, please make sure the instructions has been read and understood especially the “Safety” chapter. Please keep this manual in a good condition for future reference. Device number is very important for quality management. Please check the device number when you buy this device.
Preface Getting start Set-up Install Adjustment Getting Help Preface Table of contents Preface…………………………..2 Table of contents...........................2 Caution for Safety........... ..............4 Caution for correct usage ...........12 Terminology.................................14 The process of using the device.16 Getting start……………………17 Step 1: Accessories and tools ....17 Step 2: Insert the SD memory car ......................................... ...18 Step 3: Connect device with AC adapter...
Outlook of the operational manual Outlook of symbols in the manual. Caution: watch out for the operation. Memo: limits of function and usage are written as reference. About the contents of this manual. z This is a copyrighted material. Any use of this copy without proper permission is forbidden. z The devices from other companies mentioned in the manual are trademark or logo of other companies. The marks such as TM, ®, © are omitted in the manual.
Preface Getting start Set-up Install Adjustment Getting Help Caution for Safety There are many signs written in the manual or shown in the device. These signs are for the safety of customers, surrounding people and properties. Please pay careful attention to these signs before you read this manual. Warning: This signs means: should this sign be ignored or mistaken, the possible death or injury may take place.
Warning When abnormality takes place If the following situations occur, please do not use the device because fire or electric shock may take place. • When smoke or strange smell occurs. • When videos or the sounds can’t be played. • When water or objects are get inside the device. • When the cabinet is dropped and damaged. • When the power cord is damaged, such as cord line exposure or disconnection. As the above situations take place, please immediately turn off the power and unplug the plug.
Preface Getting start Set-up Install Adjustment Getting Help Caution for Safety (continued) Warning About handling Do not remove the rear cover or remodel the device If the supply voltage inside is high, fire or electric shock may break out. Please return the device to stores for inner part examination and repair. Do not place this device on an unstable place Please do not place this device on an unstable or inclined place because the device may fall on the ground and become damaged.
About power cord Do not use the power cord with devices other than Sign Show 7POP Do not use the power cord with devices other than Sign Show 7POP, because it may cause fire or electric shock. Do not damage the electric cord Do not damage the power cord, because it may cause fire or electric shock. • Do not modify the power cord. • Do not twist, distort or pull the power cord. • Do not put the device or heavy objects over the power cord. • Do not put the power cord close to thermal objects.
Preface Getting start Set-up Install Adjustment Getting Help Caution for Safety (continued) Caution! About power cord, power plug and AC adapter Please use the exclusive AC adapter, or fire or electric shock may break out. Please disconnect all links with machines and then connect the power plug, or fire or electric shock may break out. Moreover, please connect AC adapter to the device with DC plug, and then plug into outlet of wall.
About handling Do not put the device in the following places because it may cause fire or electric shock. • The place with dust or wetness • The place with smoke or heated air , such as close to humidifying or cooking place. • The place close to heat appliances • Window-closed automobiles or places with direct sunray. • The place close to windows, which may easily have water drop.
Preface Getting start Set-up Install Adjustment Getting Help Caution for Safety (continued) Caution! About moving Do not move this device when there are objects onto it. If the objects fall down, people may get hurt. When moving the device, please unplug the power or connecting cord. If moving the device without unplug, fire or electric shock may take place.
About falling-proofing In order to prevent falling, please take the following measures People may get hurt because of falling caused by earthquake. Please make use of the stand hole at back side and fix the device to the wall or pillar firmly. Make sure to choose the firm place. * Please make good use of marketing devices, such as wire or screws.
Preface Getting start Set-up Install Adjustment Getting Help Caution for correct usage Places for safekeeping or use of device Please do not put the device at the following places Because it may cause malfunction • Place beyond the permission operating temperature (0℃~40℃) • Place beyond the permission operating humidity (10%~80%) • Place with high magnetic force such as transformer or motor • Place close to transceiver or cell phones with high electromagnetic wave.
About handling Do not excessively use the device The reciprocal heat or sounds can cause malfunction or damages, which can lead to fire. Do not put any containers with water, such as vase or cup because it may cause fire or electric shock Do not insert any object inside because it may cause fire or electric shock. Please use the devices at place with proper light in order to protect the eyes. If looking at the screen for a long time in a place with improper light, it may cause eye tiredness.
Preface Getting start Set-up Install Adjustment Getting Help Terminology 3 4 2 1 5 6 7 8 9 10 11 12 13 14 Remove the base cover for access.
Attention light To light up the rear piece of the device. The battery cover Remove battery cover at the following situation: To alter the set-up by button To change the batteries UButton To set up the menu, it is used moving the cursor up ( to see page 25) To show the picture again, it is used to make it brighter. ( to see page 60) VButton To set up the menu, it is used for moving the cursor below ( to see page 25) To show the picture again, it is used to make it darker.
Preface Getting start Set-up Install Adjustment Getting Help The process of using the device Step 1 Please prepare the accessories and tools you need --------------------------------------------------- page 17 T Preparing Step 2 Please insert the SD memory card into the device ----------------------------------------------------- page 18 T Step 3 Please connect the AC adapter with the device - page 19 T Step 4 Please format the SD memory card----------------- page 20 T Step 5 Please plac
Getting start Step 1: Accessories and tools Accessories included with the device Necessaries for Must read it Quick Start Guide Quick Start Guide * 1 AC Adapter and power cord * 1 Necessaries for installing sticker of “replay from start” Simple stand*1 screws packaged with stand(M3)*2 Things to prepare Content files SD memory card CD-R ( UM, Layout editor ) sticker of “replay from start”*1 Tool USB memory with content files Screwdriver Memo: • USB memory has to save the contents which are
Preface Set-up Getting start Install Adjustment Getting Help Step 2: Insert the SD memory card • Please insert the SD memory card into the device • Please make sure to unplug the power before insert the SD memory ( 56 page) 1. Take off the rear cover: remove the screws by using the screwdriver Screwdriver Screws attached on Memo: • When taking out the SD memory card, please make sure to unplug the power and push the memory card to the depth.
Step 3: Connect device with AC adapter • When connecting device with AC adapter, the power will be on • When plugging the DC plug into the DC terminals, please turn the DC plug sideways as the following picture.
Preface Getting start Set-up Install Adjustment Getting Help Step 4: Format the SD memory card Before using your SD card for the first time, a format may be required. Notice: • Formatting an used SD memory card will erase all the saved files. • The SD memory card will be unusable by computers if formatting is done on this device. 1. To show the menu screen Turn on the power, and then press the right button and left button simultaneously for 2 seconds.
Format the SD memory card (continued) 3. To display the capacity of 5. To practice the formatting memory Select “memory capacity” by up or down button, and then press the set button. Select the “yes” by up or down button, and then press the set button. ⇒ Start to format the SD memory card. T 4. To display the formatting screen Select the “initialization” by up or down button, and then press the set button.
Preface Set-up Getting start Install Adjustment 6. Return to the menu screen Please select “ return” after completing formatting and then press the set button. ⇒ In the screen of memory card capacity, the capacity of formatted SD memory card will display. Getting Help Memo: • When taking out the SD memory card, please make sure to turn off the power and then push the SD memory card to the depth.
Step 5: To update the configure file and content files To transmit the content file that is saved in USB memory to SD memory card. Content files Transmitted time 10 MB About 10 seconds 50 MB About 50 seconds 100 MB About 1 minute and 40 seconds 250 MB About 4 minutes and 10 seconds 500 MB About 8 minutes and 20 seconds * This is the speculation for transmitting time. The time depends on the type of USB memory and SB memory card.
Preface Getting start Set-up Install Adjustment 1. To turn on the power Please make sure that the power light is green or orange color. Power light 2. To insert the USB memory into the USB terminal Please take off the base cover of terminal, and insert the USB memory into USB terminal. * Please leave the OSD menu first.
The message will show “A CONFIGURATION FILE IS FOUND!” Use the same steps as you would in updating content files to update the configuration files. ⇒ The message will be shown as the following picture. replayed, the content files can still be replaced. • If the replaying time has been set beforehand for the transmitted contents , please replay it following the instruction of replaying time setting. Memo: • The message shown as the picture below means the failure of transmission.
Preface Getting start Set-up Install Adjustment Getting Help Before the set-up Set-up Buttons used for set-up The outlook of selecting item Please use the 4 buttons inside the cover of rear operation button. To select the menu The selected item displays in the word of white color.
To make sure the setting content of all content files Make sure the setting content of replaying day or time of content files and then write the contents in the following table.
Preface Getting start Setting screen of OSD System Day/time setting ( to see page 38) Set-up Install Adjustment Getting Help Setting contents Assure the The model, operation time, firmware version system can be assured * setting can't be practiced Memory Make sure the space of SD memory card, capacity capacity, range, or to initialize the SD card Renew *Practice only by service man firmware Back to the Back to the original setting original setting Day Set the present day, year, month, day) Settin
Setting contents and items Mode Schedule setting ( to see page 42) Loop replay Schedule replay Replaying Replay selection Don't replay Replay Volume time Repetition setting of setting all content files (select the name of content files The replayable content ( to be set loop replay, [replay] at replaying selection)can schedule replay be repeatedly replayed at the setting time of [timer setting] The replayable content ( to be set [replay] at replaying selection) can be replayed at the setting time.
Preface Getting start Set-up Install Adjustment Setting screen Setting contents Schedule setting Starting time Finishing time Starting day Finishing day Replaying due day Setting the replay time of content files( to select the name of content files) Getting Help Setting the replay time Setting the finishing time Set up when the repetition setting year: 2007~2032 is on month: 01~12 day: 01~31 To set [repetition setting] as “Weekly”: Repetition occurs at the setting day with “on” (* symbol) To se
Constitution of setting screen System setting screen Date/time setting screen of d t /ti Network setting screen Menu screen Auto download screen (Network Mode: Active) Web page setting screen (Network Mode: Passive) Timer setting screen Schedule setting screen LED On/Off setting screen Others setting screen Exit 31
Preface Getting start Set-up Install Adjustment Getting Help Step 6: Set up the network and online access • Set up the network • Set up the web page • Set up the auto download Buttons used in network settings 1. To display the menu screen Please press the left and right button simultaneously for 2 seconds. Up button Down button Right button Left button Set button < Menu screen> 2.
3. To set the network mode Select “Network Mode” and press the set button. ⇒ The selected item turns from white to blue. Press the left or right button to toggle “Active” or “Passive”. • Selecting “Active” will allow you to use the “Auto Download” function and upload contents to your device. • Selecting “Passive” will allow you to use the “Web page” function and have access to the device via a web page. 5.
Preface Getting start Set-up Install Adjustment Getting Help 6. To set the web page Web page settings become available if “Passive” Network Mode is selected in Network settings. Select “Web page” using the up or down button and press the set button. ⇒ The following screen displays. 7. To set the auto download Auto download settings become available if “Active” Network Mode is selected in the Network settings OSD menu. Select “Auto download” using the up or down button and press the set button.
Set up the network and online access (continued) To access the device via a web page Connect your PC and networks to your device to use this function. and transfer the file to the device using a USB drive. File will be found after you restart the device. 1. To display the menu screen on the web Web access becomes available if “Passive” Network Mode is selected in Network settings. Open a web browser on your PC and enter the IP address. IP address information can be viewed from the Web page settings screen.
Preface Getting start Set-up Install Adjustment Getting Help 3. To set up the play menu 4. To set the other menu Play menu allows you to view your schedule edit, take snap shot of your contents, and upload files to the device. Other menu allows you to enable or disable time setting, LED, return switch, and login authentication. Select the “Play” tab on top to open the drop down menu. ⇒ The following screen displays. Select the “Other” tab on top to view the other menu.
5. To set up the network menu 6. To view the system log Network menu allows you to set up your network settings. System log allows you to view information on OSD, Play, System, and Other. Select the “Network” tab on top to view the network menu. ⇒ The following screen displays. Select the “Log” tab on top to view the system log. ⇒ The following screen displays.
Preface Getting start Set-up Install Adjustment Getting Help Set up the network and online access (continued) To upload contents using auto download Connect your PC and networks to your device to use this function. An ftp site must be set up first before using this function. Auto download settings become available if “Active” Network Mode is selected in Network settings. To upload contents to your device from ftp, use a content packer to create a zip file, such as “content.
Step 7: Set the present time and date • Set the present time and day • Must set the present time and day before setting replaying time • Button for setting Button for setting 1. To display the menu screen Please press the left and right button simultaneously for 2 seconds. Up button Down button Right button Left button Set button < Menu screen> 2.
Preface Getting start Set-up Install Adjustment Getting Help 3. To set the date (year/month/ day) 4. To set the time ( hour: minute: Select the item by using the left or right button, and then press the set button. ⇒ Setting items display in the word of blue color. second) Select the item by left or right button and then press the set button. ⇒ Setting items display in the word of blue color. T Change the setting value by using up or down button and then press the set button.
Step 8: Select the replaying contents (set to replay contents) To replay or not to replay the saved contents in SD memory card Memo: • At original setting, it is set up as “replay.
Preface Getting start Set-up Install Adjustment Getting Help 1. To display the menu Please press the left and right button simultaneously for 2 seconds. T Select the “ don’t replay” by using up or down button, and then press set button. ⇒ Replaying selection displays in the word of white color.
Step9: Set the replay time To replay the contents at the same time (timer setting) To replay the contents which are set to replay at “contents replaying setting”.
Preface Getting start Set-up Install Adjustment Getting Help 1. To display the menu screen 3. To set timer setting “on” Please press the left and right button simultaneously for 2 seconds. Make sure the selected setting values of [timer setting] and then press the set button. ⇒ To display in the word of blue color. Shown in the word of blue color < Menu screen> 2. To display the timer setting screen Select the [timer setting] by up or down button and then press the set button.
Set the replay time (continued) To replay the contents at the same time (Timer setting) (continued) 4. To set the starting time( hour: 5. To set finishing time ( hour: minute: second) Make sure that the setting value of [timer setting] displays in the word of white color and then press down button. ⇒ Starting time displays in the word of white color. T Select the setting item (hour: minute: second) by using left or right button, and then press set button.
Preface Getting start Set-up Install Adjustment Getting Help 6. To set “ Saturday” as stopping 7. To set “ loop replay” [mode] day Make sure that the finishing time displays in the word of white color and then press down button. ⇒ The setting value of [stopping day] displays in the word of white color. T Please press the set button. ⇒ The setting value displays in the word of blue color. Select [schedule setting] and then press the set button. ⇒ Schedule setting screen displays.
Set the replay time (continued) To replay on the due day of every week Set up the replaying day and time of content files. Example Replay the Program 1 from 11:30AM~1:00PM every Monday and Friday.
Preface Getting start Set-up Install Adjustment Getting Help 1. To display the menu screen 4. To display the content replay Please press the left and right button simultaneously for 2 seconds. setting screen Select to content file (Program 1) which is set to replay by using down button and then press the set button. ⇒ Content replay setting screen displays and the setting values of [volume] display in the word of white color. < Menu screen> 2.
Set the replay time (continued) To replay on the due day of every week 6. To set [repetition setting] as “ every week” Make sure that the setting value of [volume] displays in the word of white color and then press down button. ⇒ Select [repetition setting] and then the setting value displays in the word of white color. T Press the set button and the setting value can be changed. ⇒ Setting value displays in the word of blue color.
Preface Getting start Set-up Install Adjustment Getting Help 9. To set up [replay due day] 10. To complete the content replay Make sure that the finishing time displays in the word of white color and the press the set button. ⇒ The “( ) Monday” of [replay due day] displays in the word of white color. T Select the day of week by using left or right button, and then press set button. ⇒ The selected day displays in the word of blue color.
Set the replay time (continued) To replay on the due day of every month Example Replay the Program 5 from 10:00AM~5:30PM on 5th and 25th of every month.
Preface Getting start Set-up Install Adjustment Getting Help 1. To display the menu screen 4. To display the content replay Please press the left and right button simultaneously for 2 seconds. setting screen Select to replay content file (Program 5) by down button and then press the set button. ⇒ Content replay setting screen displays and the setting values of [volume] display in the word of white color. < Menu screen> 2.
Set the replay time (continued) To replay on the due day of every month (continued) 6. To set [repetition setting] as 7. To set “Starting time” ( hour: “ every month” Make sure that the setting value of [volume] displays in the word of white color and then press down button. ⇒ Select [repetition setting] and then the setting value displays in the word of white color. T Press the set button and the setting value can be changed. ⇒ Setting value displays in the word of blue color.
Preface Getting start Set-up Install Adjustment 8. To set finishing time ( hour: minute: second) Make sure that the starting time displays in the word of white color and then press down button. ⇒ Finishing time (hour) displays in the word of white color. T Select the setting item ( hour: minute: second) by using left or right button, and then press set button. ⇒ Setting value of selecting items displays in the word of blue color.
Set the replay time (continued) To replay on the due period To replay the content at the same due period. Example Replay the Program 1 Program 2 Program 3 Program 4 by order from 10:00AM~8:30PM during 2008/3/1~2008/3/14.
Preface Getting start Set-up Install Adjustment Getting Help 1. To display the menu screen 4. To display the content replay Please press the left and right button simultaneously for 2 seconds. setting screen for Program 1 Select content file (Program 1) which has been set replayed by down button and then press the set button. ⇒ Content display setting screen displays and the setting values of [volume] display in the word of white color. < Menu screen> 2.
Set the replay time (continued) To replay on the predetermined period 6. To set [Repeat setting] as “ off” Make sure that the setting value of [volume] displays in the word of white color and then press down button. ⇒ Select [Repeat setting] and then the setting value displays in the word of white color. T Press the set button and the setting value can be changed. ⇒ Setting value displays in the word of blue color. T Select “off” by using up or down button and then press the set button.
Preface Getting start Set-up Install Adjustment 9. To set up [Starting day](year/month/day) Make sure that the finishing time displays in the word of white color and the press the set button. ⇒ [Starting day] (year)displays in the word of blue color. T Select the setting item (year/month/day) by using left or right button, and then press set button. ⇒ Setting value of selecting item displays in the word of blue color. T Change the setting value by using the up or down button and then press set button.
Step 10: To install the device onto the site Install To install the device Please install the device on the flat site by using the simple stand and foot packaged together with the device. Installing hole 1. To install the simple stand Screw M3 screws (accessory) into the installing hole of the device as following picture. Memo: • There are 3 stages in the installing hole of the stand. Please adjust the position of holes. 2.
Preface Getting start Set-up Install Adjustment Getting Help To paste the sticker of “ replay from start” to the device Please paste the sticker of “replay from start” to the device as the following picture. sticker of “replay from start” button Memo: • When pressing the button of “replay from start” during contents replaying, the content files will be replayed from start. Please use it as occasion demands.
To adjust the brightness and volume To adjust the brightness and volume, please use the 4 buttons inside the rear battery cell cover. Adjustment The button for adjustment of brightness and volume Up button Down button darken brighten Right button Left button To adjust the brightness To adjust the brightness by up or down button during the content replaying. Brighten the screen Press the up button to brighten the screen.
Preface Getting start Set-up Install Adjustment To adjust the volume About adjusting the volume, please go to the section of schedule setting ( page 40). However, the volume can be changed during contents replaying by using left or right button. To louder the volume Press the left button and the volume louder. To lower the volume Press the right button and the volume lower. lower louder Memo: • The volume which is set in the schedule setting displays as “01.
To use the button of “replay from start” Once pressing the button of “replay from start” during contents replaying, the content files will be replayed from start. Please paste the sticker of “replay from start” for button to the device. ( page 60) “replay from start” button Memo: • Please set [replaying from start button] “on” if the button of “replay from start” malfunctions.
Preface Getting start Set-up Install Adjustment Getting Help To turn on/ off the power by manual The power can be turn on/ off by manual without setting replay time. It can be used to replay the contents without timer setting or to turn off the power by force during replaying.
To edit the content files • With the accessory’s CD-R (General Layout Editor), the animation or static state of contents can be edited and the captions can also be set up. • With this CD-R, the setting of replay schedule can be simply operated. ( page 38) Memo: • Please take a look on the instruction of CD-R for the use of CD-R • To produce the content file, please authorize the photo-shop to make it.
Preface Getting start Set-up Install Adjustment Getting Help To change batteries for clock button For changing the batteries of buttons ( call “button” for the following mention) as clock delays. Please change the new batteries. Memo: • Please use type-CR2032 batteries. • Please adjust the date/ time again after changing the batteries. * Timer setting can be kept when changing batteries and keeping the power on. Battery protecting sheet Talon Battery for button Standard screwdriver 1.
Packaging When carrying the device, please pack it as the following picture.
Preface Getting start Set-up Install Adjustment Getting Help Getting Help Troubleshooting Before getting maintenance from professionals, take a look at the following points. Condition reason corresponding measure There is no power The power plug has Make sure to plug the power or the screen is been slacked black. and been removed.
About warranty and after sales service About warranty Please contact your local regional sales office for warranty information as each region may offer local or other warranty’s. Your can take your device for maintenance to selling stores or the supporting units which are written on the inner sheet. We do not support the maintenance which is beyond the warranty. About maintenance after warranty period About maintenance after warranty period, please ask providing stores.
Preface Getting start Set-up Install Adjustment Getting Help Specifaction Network port LCD LCD panel Valid range Screen constitution Contrast: View angle: The brightness of white surface Back light: type-7 TFT color LCD 154.08*86.58 800*RGB*400 pixel 500:1 left/right 65 degree, up 40 degree, down 65 degree 280cd/m ( panel center, 25℃) LED Output Sound Stereo speaker Volume adjustment 1.0 W+ 1.
Battery The battery for timer (CR2032) is attached with device * The specification and outlook may be changed without announcement.