CONTENTS Usage Notice .....................................................................................2 Safety Instructions ................................................................................................................. 2 Introduction .......................................................................................5 Projector Features ................................................................................................................. 5 Package Contents ............
Usage Notice Safety Instructions Read all of these instructions before you operate your projector and save for future reference. 1. Read instructions All the safety and operating instructions should be read before the appliance is operated. 2. Notes and warnings All notes and warnings in the operating instructions should be adhered to. 3. Cleaning Unplug the projector from the wall socket before cleaning. Use a damp cloth for cleaning the projector housing. Do not use liquid or aerosol cleaners. 4.
8. Replacement parts When replacement parts are required, be sure that the replacement parts are specified by the manufacture. Unauthorized substitutions may result in fire, electric shock or other hazards. 9. Moisture Condensation Never operate this projector immediately after moving it from a cold location to a warm one. When the projector is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts.
Notes on the AC Power Cord AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug.
Introduction Projector Features The projector integrates high-performance optical engine projection and a user - friendly design to deliver high reliability and ease of use. The projector offers the following features: Single chip 0.
Package Contents When you unpack the projector, make sure you have all these components: Projector AC Power Cord Remote Control (IR) & batteries (AAA *2 PCS) VGA Cable (D-SUB to DSUB) Carry Bag (optional for certain models) Remote Control (IR) & batteries (AAA *2 PCS) for certain regions Documentation: 5User's Manual 5Warranty Card 5Quick Start Card 5WEEE Card (for EMEA only) Note For European warrant information please visit www.optomaeurope.
Projector Overview Front View 1 2 3 4 5 Front IR remote control sensor Elevator foot Projection lens Speaker Ventilation holes 9 8 1 2 7 6 4 3 6 7 8 9 5 Control panel Zoom ring Focus ring Lamp cover EN-7
Rear View 1 1 2 3 2 2 3 AC power socket Connection ports (HDMI is only on certain models) Kensington lock Bottom View 3 1 2 1 2 3 Security bar Ceiling mount holes Ventilation holes Note This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package. Contact your dealer for information to mount the projector on a ceiling.
Using the Product Control Panel 1 2 3 4 5 6 7 8 4 1 2 3 4 5 6 7 8 Power Turn the projector on or off. SOURCE Switch between input signals. MENU/EXIT Display or exit the on-screen display menus. Keystone ( / ) Manually correct distorted images resulting from an angled projection. Four directional buttons Use four directional buttons to select items or make adjustments to your selection. Re-SYNC Automatically synchronize the projector to the input source.
Connection Ports 1 10 1 2 3 4 5 6 7 8 9 10 2 3 4 5 9 8 7 6 AUDIO IN Connect an audio output from video equipment or computer to this jack. HDMI (HDMI is only on certain models) Connect HDMI output from video equipment to this jack. S-VIDEO Connect S-Video output from video equipment to this jack. VGA1-IN/YPbPr Connect image input signal (analog RGB or component) to this jack. RS-232 When operating the projector via a computer, connect this to the controlling computer's RS-232C port.
Remote Control 1 2 3 4 5 6 7 8 9 Switch Switch to mouse mode when the on-screen menus are close. Source Switch between input signals. Four directional buttons Use four directional buttons to select items or make adjustments to your selection. Left mouse Perform the left button of the mouse when mouse mode is activated. Keystone ( / ) Manually correct distorted images resulting from an angled projection. Brightness Display the setting bar for adjustment of brightness.
14 15 16 17 18 19 20 21 22 Enter Confirmed selections. Right mouse Perform the right button of the mouse when mouse mode is activated. Volume ( / ) Adjust the volume level. Menu Display on-screen display menus. ZOOM Magnifies or reduces the projected picture size. AV mute Cut off the AV Mute temporarily. Only pressing AV Mute again can output sound and image. If any other buttons are pressed, the projection image will become abnormal and no sound will be output. Video Display video signal.
Installing the Batteries 1. Open the battery cover in the direction shown. 2. Install batteries as indicated by the diagram inside the compartment. 3. Close the battery cover into position. Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Make sure the plus and minus terminals are correctly aligned when loading a battery. Note Keep the batteries out of the reach of children.
Remote Control Operation Point the remote control at the infrared remote sensor and press a button. Operating the projector from the front 15 15 5m 8m 7m Note The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor. Operate the remote control from a position where the remote sensor is visible. Do not drop the remote control or jolt it.
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. 1 1 1. 2. 3. 4. 5. 6. 7. 8. 2 1 3 4 6 7 6 8 5 ............................................................................................ *Audio cable ............................................................................................ *HDMI cable .....................
Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them to both IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to a notebook or desktop computer: 1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. 2.
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: HDMI Component Video S-Video Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
Connecting an HDMI source device Examine your Video source device to determine if it has a set of unused HDMI output jacks available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an HDMI source device: 1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI source device. 2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device. 2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. Take a Video cable and connect one end to the composite Video output socket of the Video source device. 2.
Operation Powering On/Off the Projector Powering On the Projector: 1. Complete the AC power cord and peripheral signal cable(s) connections. 2. Press to turn on the projector. The projector takes a minute or so to warm up. 3. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
Adjusting the Projector Height Elevator foot The projector is equipped with an elevator foot to adjust the image height. To raise or lower the image, turn the elevator foot to fine-tune the height. Note To avoid damaging the projector, make sure that the elevator foot is fully retracted before placing the projector in its carrying case. Adjusting the Projector Zoom and Focus Zoom ring Focus ring 1. Focus the image by rotating the focus ring. A still image is recommended for focusing. 2.
Adjusting Projection Image Size Refer to the graphic and table below to determine the screen size and projection distance. Maximum zoom Minimum zoom Screen Center of lens Vertical offset Projection distance 4 : 3 Screen Projection distance [inch (m)] Screen size Diagonal [inch (cm)] (min. zoom) 30 (76) 60 (152) 80 (203) 100 (254) 150 (381) 200 (508) 250 (635) 300 (762) 45.3 (1.2) 92.2 (2.3) 123.5 (3.1) 154.8 (3.9) 233.0 (5.9) 311.2 (7.9) 389.4 (9.9) 467.6 (11.9) (max.
Menu Operation The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. How to operate 1. Press MENU on the projector or Menu on the remote control to open the OSD menu. 2. When OSD is displayed, use / to select any feature in the main menu. 3. After selecting the desired main menu item, press to enter sub-menu for feature setting. 4. Use / to select the desired item and adjust the settings with / . 5.
Presentation, Bright, Movie, sRGB, User, Classroom, Black Board, 3D EN-25
Image Brightness Brighten or darken the image. Contrast Set the difference between light and dark areas. Color Settings Adjust the color temperature. At higher temperature the screen looks colder; at lower temperature, the screen looks warmer. If you select “User”, then you can change the intensity of each of 3 color (Red, Green, Blue) to customize user color temperature. Keystone Manually correct distorted images resulting from an angled projection. Zoom Zoom in and out the images.
There are many factory presets optimized for various types of images. Presentation: For computer or notebook. Bright: For bright environment. Movie: For home theater. sRGB: For PC standard color. User: Memorize user’s settings. Classroom: For projection in the classroom. Black Board: For black projection screen type. 3D: For viewing 3D videos. Brilliant Color Adjusts the Brilliant Color value to extend the exposure range and sharpens detail for grain free images.
Signal Frequency Adjust the timing of the projector relative to the computer. Tracking Adjust the phase of the projector relative to the computer. H Position (Horizontal Position) Adjust the image left or right within the projection area. V Position (Vertical Position) Adjust the image up or down within the projection area.
Video Image Color Adjust a video image from black and white to fully saturated color. Sharpness Sharpen or soften the image. Tint Shift colors toward red or green. Sound Volume Adjust the volume level. Mute Cut off the sound temporarily.
Setting Menu Position Choose the menu location on the display screen. Projection Adjust the picture to match the orientation of the projector: upright or upsidedown, in front of or behind the screen. Invert or reverse the image accordingly. Color Space Select an appropriate color matrix type from RGB,YCbCr/YPbPr. Lamp Time Display the lamp’s elapsed operating time (in hours). Lamp Time Reset Reset the lamp Hour to 0 hours. Password Set or change the password.
Source Lock On: The projector will search specified connection port. Off: The projector will search for other signals if the current input signal is lost. Bright Mode ECO: Choose “ECO” to dim the projector lamp which will lower power consumption and extend the lamp life by up to 120%. Bright: Choose “Bright” to increase the brightness. High Altitude Use this function to allow the fans operates at full speed continuously to achieve proper high altitude cooling of the projector.
Language Select the language used by the on-screen menu. Factory Default Restore settings to factory default .
Appendix Replacing the Lamp As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage. We recommend replacing the lamp if a warning message is displayed. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement. Note The lamp is extremely hot right after turning off the projector. If you touch the lamp, you may scald your finger.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Turn off the projector. If the projector is installed in a ceiling mount, remove it Unplug the power cord. Remove the screw in the side of the lamp cover. 1 Remove the cover. 2 Loosen the screws from the lamp module. 3 Raise the handle, and lift out the module. 4 Insert the new lamp module into the projector and tighten the screws. Replace the lamp cover and tighten the screw. Turn on the projector.
Ceiling mount installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: Screw type: M4*3 Maximum screw length: 8mm Minimum screw length: 6mm 278.32 139.00 54.00 73.00 231.50 120.00 38.50 29.70 57.94 61.70 210.70 12.
Compatibility Modes Computer: Mode VGA Resolution 640 x 350 640 x 350 720 x 350 640 x 400 640 x 400 720 x 400 720 x 400 720 x 576 720 x 576 640 x 480 SVGA 800 x 600 XGA 832 x 624 832 x 624 1024 x 576 1024 x 576 1024 x 768 1152 x 864 HD720 HD720 HD720 HD720 WXGA EN-36 1152 x 870 1280 x 720 1280 x 720 1280 x 720 1280 x 720 1280 x 768 H-Sync [KHz] 31.5 37.9 31.5 31.5 37.9 31.5 37.9 31.5 37.9 37.5 43.3 35.2 37.9 46.9 48.1 53.7 48.4 56.5 57.7 60 68.7 47.4 - V-Sync [Hz] 70 85 70 70 85.
WXGA-800 SXGA SXGA+ UXGA HDTV SDTV Macbook/Macbook Pro (Intel) Macbook Pro (Intel) Power Mac G4/G5 Power Mac G4 Power Mac G4 Power Mac G5 1280 x 800 1280 x 1024 1366 x 768 1440 x 900 1400 x 1050 1600 x 1200 1920 x 1080 1920 x 1080 1920 x 1080i 1920 x 1080i 1920 x 1080p 1920 x 1080p 1920 x 1080p 1920 x 1080p 1920 x 1080p 1280 x 720 1280 x 720p 1280 x 720p 720 x 576 720 x 576i 720 x 576p 720 x 480 720 x 480i 720 x 480p 800 x 600 1024 x 768 1280 x 720 1280 x 768 1680 x 1050 1280 x 800 1280 x 1024 800 x
Video: NTSC PAL SECAM SDTV HDTV EN-38 NTSC M/J, 3.58MHz, 4.43MHz PAL B/D/G/H/I/M/N, 4.43MHz SECAM B/D/G/K/K1/L, 4.25/4.
RS232 Commands and Protocol Function List RS232 Pin Assignments D-Sub 9 pin 1 2 3 4 5 6 7 8 9 1 CD RXD TXD DTR GND DSR RTS CTS RI Wire List C1 1 2 3 4 5 6 7 8 9 SHELL COLOR Black Brown Red Orange Yellow Green Blue Purple White DW C2 1 2 3 4 5 6 7 8 9 SHELL EN-39
RS232 Protocol Function List XX=01-99, projector's ID, XX=00 is for all projectors Baud Rate : 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F Note There is a after all ASCII commands. 0D is the HEX code for in ASCII code.
~XX45 n 7E 30 30 34 34 20 a 0D Color (Saturation) n = 0 (a=30) ~ 100 (a=31 30 30) ~XX44 n 7E 30 30 34 35 20 a 0D Tint n = 0 (a=30) ~ 100 (a=31 30 30) ~XX60 1 7E 30 30 36 30 20 31 0D Format ~XX60 2 7E 30 30 36 30 20 32 0D ~XX60 3 7E 30 30 36 30 20 33 0D ~XX62 n 7E 30 30 36 32 20 a 0D Zoom n = -5 (a=2D 35) ~ 5 (a=35) ~XX66 n 7E 30 30 36 36 20 a 0D V Keystone n = -30 (a=2D 33 30) ~ 30 (a=33 30) ~XX230 1 7E 30 30 32 33 30 20 31 0D 3D Mode DLP-Link ~XX230 0 7E 30 30 32 33 30 20 30 0D
~XX140 10 7E 30 30 31 34 30 20 31 30 0D ~XX140 11 7E 30 30 31 34 30 20 31 31 0D Up/Page + Left/Source ~XX140 12 7E 30 30 31 34 30 20 31 32 0D Enter (for projection MENU) ~XX140 13 7E 30 30 31 34 30 20 31 33 0D Right/Re-SYNC ~XX140 14 7E 30 30 31 34 30 20 31 34 0D Down/Page - ~XX140 15 7E 30 30 31 34 30 20 31 35 0D Keystone + ~XX140 16 7E 30 30 31 34 30 20 31 36 0D Keystone - ~XX140 17 7E 30 30 31 34 30 20 31 37 0D Volume - ~XX140 18 7E 30 30 31 34 30 20 31 38 0D Volume + ~XX140 19
Troubleshooting Refer to the symptoms and measures listed below before sending the projector for repairs. If the problem persists, contact your local reseller or service center. Please refer to "LED Indicator Messages" as well. Start-up problems If no lights turn on: Be sure that the power cord is securely connected to the projector and the other end is plugged into an outlet with power. Press the power button again.
LED Indicator Messages Projector Status Standby mode Normal running mode Normal cooling Lamp ignition failed Lamp life end Temp error Fan error Color wheel or DMD error EN-44 POWER Blue solid Flashing 30 seconds after powering on and then become solid blue Blue solid Blue solid Blue solid Blue solid Blue solid Blue flashing TEMP LAMP Off Off Off Off Blue solid Off Off Blue flashing Blue solid Blue flashing Red solid Red flashing Red solid Off Off Red flashing
Optoma Global Offices For service or support please contact your local office. USA 3178 Laurelview Ct. Fremont, CA 94538, USA 888-289-6786 www.optomausa.com services@optoma.com Canada 5630 Kennedy Road, Mississauga, ON, L4Z 2A9, Canada www.optoma.ca 905-361-2582 905-361-2581 services@optoma.com Europe 42 Caxton Way, The Watford Business Park Watford, Hertfordshire, WD18 8QZ, UK www.optoma.eu Service Tel : +44 (0)1923 691865 +44 (0) 1923 691 800 +44 (0) 1923 691 888 service@tsc-europe.
Lerpeveien 25 3040 Drammen Norway PO.BOX 9515 3038 Drammen Norway Latin America 3178 Laurelview Ct. Fremont, CA 94538, USA www.optoma.com.br Korea WOOMI TECH.CO.,LTD. 4F,Minu Bldg.33-14, Kangnam-Ku, seoul,135-815, KOREA +47 32 98 89 90 +47 32 98 89 99 info@optoma.no 888-289-6786 www.optoma.com.mx +82+2+34430004 +82+2+34430005 Japan 東京都足立区綾瀬 3-25-18 株式会社オーエスエム サポートセンター :0120-46-5040 info@osscreen.com www.os-worldwide.com Taiwan 5F., No. 108, Minchiuan Rd. Shindian City, Taipei Taiwan 231, R.O.C. www.
Changning District Shanghai, 200052, China +86-21-62947375 www.optoma.com.
Regulation & Safety Notices This appendix lists the general notices of your projector. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation.
Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003.
Remote Control Power Turn the projector on or off. L Button Perform the left button of the mouse. R Button Perform the right button of the mouse. Page + Perform page up function. Page Perform page down function. Enter/ /Help? Confirm your item selection. ? Open the Help Menu. Source Switch between input signals. Re-SYNC Automatically synchronize the projector to the input source. Four directional buttons Use four directional buttons to select items or make adjustments to your selection.
Freeze Freeze the projected image. AV mute Cut off the AV Mute temporarily. Only pressing AV Mute again can output sound and image. If any other buttons are pressed, the projection image will become abnormal and no sound will be output. S-Video Display S-Video signal. VGA Switch input source to VGA1 or VGA2 by sequence. Video Display video signal.
