CONTENTS Usage Notice ....................................................................... 2 Safety Instructions .......................................................................................... 2 Introduction ......................................................................... 5 Projector Features .......................................................................................... 5 Package Contents ....................................................................................
Usage Notice Safety Instructions Read all of these instructions before you operate your projector and save for future reference. 1. Read instructions All the safety and operating instructions should be read before the appliance is operated. 2. Notes and warnings All notes and warnings in the operating instructions should be adhered to. 3. Cleaning Unplug the projector from the wall socket before cleaning. Use a damp cloth for cleaning the projector housing. Do not use liquid or aerosol cleaners. 4.
8. Replacement parts When replacement parts are required, be sure that the replacement parts are specified by the manufacture. Unauthorized substitutions may result in fire, electric shock or other hazards. 9. Moisture Condensation Never operate this projector immediately after moving it from a cold location to a warm one. When the projector is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts.
Notes on the AC Power Cord AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug.
Introduction Projector Features The projector integrates high-performance optical engine projection and a user - friendly design to deliver high reliability and ease of use. The projector offers the following features: Single chip 0.55" Texas Instruments DLP® technology (SVGA/XGA model) Single chip 0.
Package Contents When you unpack the projector, make sure you have all these components: Projector AC Power Cord *VGA Cable (D-SUB to D-SUB) Remote Control (IR) & batteries (AAA *2 PCS) 5User's Manual 5Warranty Card 5Quick Start Card 5WEEE Card (for EMEA only) Documentation *Carry Bag *Dust filter Note For European warranty information please visit www.optomaeurope.com Due to the difference in applications for each country, some regions may have different accessories.
Projector Overview Front View 9 7 8 Airflow Out Airflow In 1 2 3 1 2 3 4 5 Front IR remote control sensor Elevator foot Projection lens Focus ring Speaker 4 6 7 8 9 5 6 Ventilation holes Zoom ring Control panel Lamp cover EN-7
Bottom View 1 2 1 2 2 Security bar Ceiling mount holes Note This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package. Contact your dealer for information to mount the projector on a ceiling.
Using the Product Control Panel 1 2 7 3 4 5 8 9 10 6 11 1 1 2 3 4 5 6 7 8 9 10 11 Keystone ( / ) Manually correct distorted images resulting from an angled projection. TEMP (Temp LED indicator) Refer to “LED Indicator Messages” on page 62. SOURCE Switch between input signals. POWER (Power LED indicator) Refer to “LED Indicator Messages” on page 62. Power Turn the projector on or off. HELP Display Help menu. LAMP (Lamp LED indicator) Refer to “LED Indicator Messages” on page 62.
Connection Ports SVGA/XGA 1 AUDIO-IN 2 3 4 VGA1 / YPbPr VGA-OUT 5 6 S-VIDEO 7 MOUSE 8 USB Power Out(5V 1A) 1 (VGA1/2) 2 (S-VIDEO VIDEO) AUDIO OUT RS-232C SERVICE HDMI VGA2 / YPbPr VIDEO 12 11 10 9 WXGA AUDIO-IN S-VIDEO MOUSE USB Power Out(5V 1A) 1 (VGA1/2) VGA1 / YPbPr 2 (S-VIDEO VIDEO) AUDIO OUT 1 2 3 4 5 6 RS-232C VGA-OUT SERVICE HDMI VGA2 / YPbPr VIDEO AUDIO-IN 1 Connect an audio output from a computer to this jack connector.
7 8 Service/Mouse This connector supports firmware update, remote mouse and page up/ down. Power Out (5V DC 1A) Power charging (5V DC 1A). Do not connect devices that require or draw more power than 5v 1A. Over drawing can cause damage and create safety concerns. 9 10 11 12 VGA2-IN/YPbPr Connect image input signal (analog RGB or component) to this jack. VIDEO Connect composite video output from video equipment to this jack. AUDIO-OUT Connect to an external speaker system.
Remote Control 13 1 14 2 3 15 4 17 16 18 19 20 21 22 23 24 25 26 5 6 7 8 9 10 11 12 27 1 2 3 4 5 6 Power Turn the projector on or off. Blank & Audio mute Momentarily blanks video and mutes audio. Left mouse Perform the left button of the mouse when mouse mode is activated. Four directional buttons Use four directional buttons to select items or make adjustments to your selection. "UP" key: When menu is off, up key for emulation of USB mouse.
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Format Selects the display aspect ratio. VGA Switch input source to VGA1 or VGA2 by sequence. HDMI Display HDMI signal. User1 User1 definable key for customized function. Source Switch between input signals. User2 User2 definable key for customized function. Switch Activate/de-activate remote mouse function. Freeze Freeze the projected image. Mute Momentarily turns off/on the audio.
27 Numbered keypad Press 0 to 9 to enter a password when required. Note Remote Control (IR) or Remote Control with Laser Pointer (depending on region). See Appendix for the Remote with Laser Pointer. Using the remote mouse control The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. 1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse.
Installing the Batteries 1. Open the battery cover in the direction shown. 2. Install batteries as indicated by the diagram inside the compartment. 3. Close the battery cover into position. Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Make sure the plus and minus terminals are correctly aligned when loading a battery. Note Keep the batteries out of the reach of children.
Remote Control Operation Point the remote control at the infrared remote sensor and press a button. Operating the projector from the front 15 15 5m 8m 7m Note The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor. Operate the remote control from a position where the remote sensor is visible. Do not drop the remote control or jolt it.
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. 6 1 1 1 2 3 4 7 6 8 5 9 AUDIO-IN S-VIDEO MOUSE USB Power Out(5V 1A) 1 (VGA1/2) VGA1 / YPbPr 2 (S-VIDEO VIDEO) AUDIO OUT 1. 2. 3. 4. 5. 6. 7. 8. 9. RS-232C VGA-OUT SERVICE HDMI VGA2 / YPbPr VIDEO ......................................................................
Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them to both IBM® compatible and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to a notebook or desktop computer: 1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. 2.
Connecting a monitor If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the VGA-OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below: To connect the projector to a monitor: 1. Connect the projector to a computer as described in “Connecting a computer” on page 18. 2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor.
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: HDMI Component Video S-Video Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
Connecting an HDMI source device Examine your Video source device to determine if it has a set of unused HDMI output jacks available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an HDMI source device: 1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI source device. 2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device. 2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
Operation Powering On/Off the Projector Powering On the Projector: 1. Connect the AC power cord and relevant peripheral signal cable(s) to the projector. 2. Press to turn on the projector. The projector takes a minute or so to warm up. 3. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
Adjusting the Projector Height Tilt-adjustment foot Elevator foot The projector is equipped with an elevator foot to adjust the image height. 1. To raise or lower the image, turn the elevator foot. 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height. Note To avoid damaging the projector, make sure that the elevator foot and tilt- adjustment foot are fully retracted before placing the projector in its carrying case.
Adjusting Projection Image Size Refer to the graphic and table below to determine the screen size and projection distance. Maximum zoom Minimum zoom Screen Center of lens Vertical offset Projection distance SVGA/XGA model Screen size Diagonal [inch (cm)] 30 (76) 40 (102) 60 (152) 80 (203) 100 (254) 120 (305) 150 (381) 200 (508) 250 (635) 300 (762) 4 : 3 Screen Projection distance [feet (m)] Image height Vertical offset [inch (cm)] [inch (cm)] (min. zoom) (max. zoom) 3.83 (1.17) 4.33 (1.32) 18 (46) 2.
WXGA model Screen size Diagonal [inch (cm)] 30 (76) 40 (102) 60 (152) 80 (203) 100 (254) 120 (305) 150 (381) 200 (508) 250 (635) 300 (762) 16:10 Screen Projection distance [feet (m)] Image height Vertical offset [inch (cm)] [inch (cm)] (min. zoom) (max. zoom) 3.08 (0.94) 3.92 (1.19) 16 (40) 2.4 (6) 4.12 (1.27) 5.17 (1.57) 21 (54) 3.2 (8) 6.33 (1.93) 7.83 (2.39) 32 (81) 4.8 (12) 8.42 (2.57) 10.5 (3.20 42 (108) 6.4 (16) 10.58 (3.23) 13.08 (3.99) 53 (135) 7.9 (20) 12.75 (3.89) 15.75 (4.80) 64 (162) 9.
Menu Operation The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. How to operate 1. To open the OSD menu, press “Menu” on the Remote Control or Projector Keypad. 2. When OSD is displayed, use / key to select to select any item in the main menu. While making a selection on a particular page, press or “Enter key to enter sub menu. 3. Use / key to select the desired item and press / /”Enter” key to enter the Single-Item-Menu. 4.
Menu tree Main Menu Single-Item Menu SVGA / XGA: Presentation / Bright / Movie / sRGB / Blackboard / User / 3D WXGA: Presentation / Bright / Movie / sRGB / Blackboard / Game / ISF Day / ISF Night / User / 3D Sub-Menu Display Mode Brightness Contrast Sharpness Color Tint IMAGE Film / Video / Graphics / Standard Gamma BrilliantColor™ Color Temp.
Yellow Color Settings White Hue / Saturation / Gain Red / Green / Blue Reset Exit Color Space IMAGE Advanced Signal Automatic Phase (VGA) Frequency (VGA) H. Position (VGA) V.
Language Projection Menu Location 16: 10/16:9 (WXGA) On / Off Month / Day / Hour Screen Type Security SETUP Security Timer Security Change Password Exit Projector ID Audio Settings Mute Volume Audio Input Logo Advanced EN-30 Closed Captioning Exit On / Off Audio Default / Audio 1 / Audio 2 Default / Neutral Off / CC1 / CC2
Input Source Source Lock High Altitude Information Hide Keypad Lock Test Pattern IR Function Background Color User 1 Remote Settings User 2 OPTIONS User 3 Advanced Lamp Settings Direct Power On Auto Power Off (min.) Sleep Timer (min.
OPTIONS Optional Filter Settings Reset EN-32 Optional Filter Installed Filter Usage Hours Filter Reminder Filter Reset Exit Yes / No On / Off Yes / No Yes / No
IMAGE Display Mode There are many factory presets optimized for various types of images. Presentation: Good color and brightness from PC input. Bright: Maximum brightness from PC input. Moive: For home theater. sRGB: Standardised accurate color. Blackboard: This mode should be selected to achieve optimum color settings when projecting onto a blackboard (green). User: User’s settings. 3D: Recommended setting for 3D mode.
Contrast Set the difference between light and dark areas. Sharpness Sharpen or soften the image. Color Adjust a video image from black and white to fully saturated color. Tint Shift colors toward red or green. Note “Color” and “Tint” functions are only supported under Video mode. Advanced Gamma This allows you to choose a degamma table that has been fine-tuned to bring out the best image quality for the input. Film: for home theater. Video: for video or TV source. Graphics: for image source.
enhanced image, adjust toward the maximum setting. For a smoother, more natural image, adjust toward the minimum setting. Color Temp. If set to cold temperature, the image looks more blue. (cold image) If set to medium temperature, the image maintains normal colorings for white. If set to warm temperature, the image looks more red. (warm image) Color Settings Press / /“Enter” key to enter the next menu as below and then use / key to select color. Press “Enter” to finalize the selection.
Return the display parameters on IMAGE menu to the factory default settings.
DISPLAY Format Use this function to choose your desired aspect ratio. For SVGA/XGA models: Source 4:3 16:9 Native 480i/p 576i/p 1080i/p 720p 1024x768 center 1024x576 center Displays the original image without any scaling. If source is 4:3, auto resize to 1024 x 768 If source is 16:9 auto resize to 1024 x 576 Auto (Default) If source is 15:9 auto resize to 1024 x 614 If source is 16:10 auto resize to 1024 x 640 PC For WXGA models: 16:9 or 16:10 depend on “Screen Type” setting.
Input source will be fit into 1280x800 display area and be kept its original aspect ratio. If source is 4:3, auto resize to 1066 x 800 Auto (Default) If source is 16:9 auto resize to 1280 x 720 If source is 15:9 auto resize to 1280 x 768 If source is 16:10 auto resize to 1280 x 800 16:9 Screen 16 : 9 screen 480i/p 576i/p 1080i/p 720p PC 4:3 960x720 center 16:9 1280x720 center LBX 1280x960 center, then get the central 1280x720 image to display.
Off: Select “Off” to turn off 3D mode. DLP Link: Select “DLP Link” to use optimized settings for DLP Link 3D glasses. 3D--->2D 3D: Select 3D format. L: Select left eye data. R: Select right eye data. 3D Format SBS: Use this mode for “Side-by-side” format 3D content. Top and Bottom: Use this mode for “Top and Bottom” format 3D content. Frame Sequential: Use this mode for “Frame Sequential” format 3D content. 3D Sync. Invert Press the “On” to invert left and right frame contents.
SETUP Language Select the language used by the on-screen menu. Press / /“Enter” key to enter the sub menu and then use the / / / key to select your preferred language. Press “Enter” to finalize the selection. Projection Adjust the picture to match the orientation of the projector: upright or upsidedown, in front of or behind the screen. Invert or reverse the image accordingly. Menu Location Choose the menu location on the display screen.
Security Timer Use this function to set the how long (Month/Day/Hour) the projector can be used. Once this time has elapsed you will be requested to enter your password again. Change Password First time: 1. Press “Enter” to set the password. 2. The password has to be 4 digits. 3. Use number button on the remote to enter your new password and then press “Enter” key to confirm your password. Change Password: 1. Press “Enter” to input old password. 2.
Audio Input Select audio input sources. Advanced Logo Use this function to set the desired startup screen. If changes are made they will take effect the next time the projector is powered on. Default: The default startup screen. Neutral: Neutral startup screen. Closed Captioning Use this function to set the desired startup screen. If changes are made they will take effect the next time the projector is powered on. Off: select “Off” to turn off the closed captioning feature.
OPTIONS Input Source Use this option to enable / disable input sources. Press / /“Enter” key to enter the sub menu and select which sources you require. Press “Enter” to finalize the selection. The projector will not search for inputs that are not selected. Source Lock On: The projector will only search current input connection. Off: The projector will search for other signals if the current input signal is lost. High Altitude When “On” is selected, the fans will spin faster.
Keypad Lock When the keypad lock function is “On”, the control panel will be locked however, the projector can be operated by the remote control. By selecting “Off”, you will be able to reuse the control panel. Note To turn off the keypad lock, press and hold “Enter” key on top of the projector for 5 seconds. Test Pattern Display a test pattern. There are Grid, White pattern and None. IR Function Choose “On” to turn on the IR receiver. Choose “Off” to turn off the IR receiver.
Power Mode (Standby) Set whether the VGA-OUT function works when the projector is in standby (powered off but connected to AC power). Eco: The VGA-OUT function will not work when the projector is in standby. Active: The VGA-OUT and AUDIO-OUT functions will work when the projector is in standby. Note When Power mode (Standby) is set to Eco (<0.5W), the VGA output, Audio pass- through will be deactivated when the projector is in standby. Lamp Settings Lamp Hours Display the projection time.
Filter Reminder Sets a filter reminder if timer is up. Filter Reset Reset the dust filter hour counter after replacing the dust filter. Reset Choose “Yes” to return the display parameters on all menus to the factory default settings.
Appendix Installing the Dust Filter (Optional accessory) Be sure to follow the steps to install the dust filter. 1. Align the filter with these two hook positions (#1 & #2), then press it close to the projector from the left side to the right one. 2. Press the last hook position (#3) until it clicks. dust filter 1 2 3 3. Turn on the projector, then press “Menu”, go to OPTIONS > Optional Filter > Optional Filter Installed and select “Yes”. 4. Clean the dust filter periodically.
Replacing the Lamp Over time, the brightness on the lamp is expected to decrease gradually. It is recommended to replace the lamp when the warning message pops up on the projected image. If somehow the lamp has shattered, it is recommended to get the lamp replaced by a qualified service personal. Note The lamp is extremely hot right after turning off the projector. If you touch the lamp, you may scald your finger.
1. 2. 3. 4. 5. 6. 7. 8. 9. Turn off the projector. Unplug the power cord. Remove the screw in the side of the lamp cover. 1 Lift the cover. 2 Loosen the screws from the lamp module. 3 Raise the handle and pull out the lamp module slowly and carefully. 4 Insert the new lamp module into the projector and tighten the screws. Replace the lamp cover and tighten the screw. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp. 10. Reset the lamp hour.
Ceiling mount installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: Screw type: M4*3 Maximum screw length: 8mm Minimum screw length: 6mm Lens 114.4 82.3 27.6 55.0 103.5 Unit: mm 110.0 108.1 68.5 73.1 Note Please note that damage resulting from incorrect installation will void the warranty. Warning 1.
Compatibility Modes Computer Compatibility Signal VGA SVGA Resolution 640 X 480 800 X 600 XGA 1024 X768 HDTV(720P) 1280 X 720 1280 X768 1280 X800 1366 x 768 1280 X1024 1400 X1050 1600 X 1200 1920 X1080 1920 X1200(*1) WXGA SXGA SXGA+ UXGA HDTV(1080p) WUXGA Refresh Rate(Hz) Notes for Mac 60/67/72/85 Mac 60/72/85 60(*2)/72/85/120(*2) Mac 60/72/85 60(*2)/70/75/85/ Mac 60/70/75/85 120(*2) 50/60(*2)/120(*2) Mac 60 60/75/85 Mac 60/75/85 60 Mac 60 60 Mac 60 60 Mac 60/75 60 60 60 Mac 60 60 Mac 60 (*1)1920 x
Input Signal for HDMI Signal VGA SVGA Resolution 640 X 480 800 X 600 XGA 1024 X 768 SDTV(480I) SDTV(480P) SDTV(576I) SDTV(576P) WSVGA(1024X600) HDTV(720p) 640 X 480 640 X 480 720 X 576 720 X 576 1024 X 600 1280 X 720 1280 X768 1280 X800 1366 x 768 1440 x 900 1280 X1024 1400 X1050 1600 X 1200 1920 X1080 1920 X1080 1920 X1200(*1) WXGA WXGA+ SXGA SXGA+ UXGA HDTV(1080I) HDTV(1080p) WUXGA Refresh Rate(Hz) Notes for Mac 60 Mac 60/72/85 60(*2)/72/85/120(*2) Mac 60/72/85 60(*2)/70/75/85/ Mac 60/70/75/85 120(
True 3D Video Compatibility table HDMI 1.4a 3D Input Input Resolutions HDMI 1.
IR Code Customer code: 32CD Key code Printing-key definition 81 Power on/off 3E Switch 8A 8B Freeze 92 CB L CC R C6 Up arrow C8 Left arrow C9 Right arrow C7 Down arrow EN-54
C5 CA 95 C1 C2 85 84 8C 8F 98 88 93 86 9G 9H 9I 9J 9K C3 96 C4 Enter Enter Mode Page+ PageKeystone+ KeystoneVolume + Volume Menu/2 3D/3 HDMI/4 VGA/5 Video/6 User 1/7 User 2/8 User 3/9 Source /0 Re-Sync The IR codes below are for user-defined remote only.
RS232 Commands and Protocol Function List RS232 Pin Assignments D-Sub 9 pin (from the projector side) 1 2 3 4 5 6 7 8 9 Wire List (from the cable side) 1 CD RXD TXD DTR GND DSR RTS CTS RI C1 1 2 3 4 5 6 7 8 9 SHELL COLOR Black Brown Red Orange Yellow Green Blue Purple White DW RS232 Protocol Function List Baud Rate : 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F XX=01-99, projector's ID, XX=00 is for all p
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to projector ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code Function Description ---------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX61 n 7E 30 30 36 31 20 a 0D Edge mask n = 0 (a=30) ~ 10 (a=31 30) ~XX62 n 7E 30 30 36 32 20 a 0D Zoom n = -5 (a=2D 35) ~ 25 (a=32 35) ~XX63 n 7E 30 30 36 33 20 a 0D H Image Shift n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30) ~XX64 n 7E 30 30 36 34 20 a 0D V Image Shift n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30) ~XX66 n 7E 30 30 36 3
~XX82 1 7E 30 30 38 32 20 31 0D Logo Default ~XX82 3 7E 30 30 38 32 20 33 0D Neutral ~XX88 0 7E 30 30 38 38 20 30 0D Closed Captioning Off ~XX88 1 7E 30 30 38 38 20 31 0D cc1 ~XX88 2 7E 30 30 38 38 20 32 0D cc2 ~XX89 0 7E 30 30 38 39 20 30 0D Audio Input Default ~XX89 1 7E 30 30 38 39 20 31 0D Audio1 ~XX89 3 7E 30 30 38 39 20 33 0D Audio2 ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND from projector automatically ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code Function Projector Return Description ------------------------------------------------------------
Troubleshooting Refer to the symptoms and measures listed below before sending the projector for repairs. If the problem persists, contact your local reseller or service center. Please refer to "LED Indicator Messages" as well. Start-up If no lights turn on: Be sure that the power cord is securely connected to the projector and the other end is plugged into an outlet with power. Press the power button again.
LED Indicator Messages Message Power LED (Red) Standby State (Input power cord) Steady light Power LED (Green) Power on (Warming) Flashing 0.5 sec off 0.5 sec light Power on & Lamp lighting Steady light Quick Resume (100 secs) EN-62 Lamp LED (Red) Flashing 0.5 sec off 0.5 sec light Back to Red steady light when cooling fan turns off Flashing 0.25 sec off 0.
Optoma Global Offices For service or support please contact your local office. USA 3178 Laurelview Ct. Fremont, CA 94538, USA 888-289-6786 www.optomausa.com services@optoma.com Canada 3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.com 888-289-6786 services@optoma.com Europe 42 Caxton Way, The Watford Business Park Watford, Hertfordshire, WD18 8QZ, UK www.optoma.eu Service Tel : +44 (0)1923 691865 +44 (0) 1923 691 800 +44 (0) 1923 691 888 service@tsc-europe.
Scandinavia Lerpeveien 25 3040 Drammen Norway PO.BOX 9515 3038 Drammen Norway Latin America 3178 Laurelview Ct. Fremont, CA 94538, USA www.optoma.com.br Korea WOOMI TECH.CO.,LTD. 4F,Minu Bldg.33-14, Kangnam-Ku, seoul,135-815, KOREA +47 32 98 89 90 +47 32 98 89 99 info@optoma.no 888-289-6786 www.optoma.com.mx +82+2+34430004 +82+2+34430005 Japan 東京都足立区綾瀬 3-25-18 株式会社オーエス コンタクトセンター：0120-380-495 info@os-worldwide.com www.os-worldwide.com Taiwan 12F., No.213, Sec. 3, Beixin Rd., Xindian Dist.
中国 上海市长宁区 凯旋路 1205 号 5 楼 琉璃奥图码 +86-21-62947376 +86-21-62947375 www.optoma.com.
Regulation & Safety Notices This appendix lists the general notices of your projector. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation.
Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003.
